RCU Forums

RCU Forums (https://www.rcuniverse.com/forum/)
-   Electric Indoor & Micro RC Flight (https://www.rcuniverse.com/forum/electric-indoor-micro-rc-flight-182/)
-   -   Storm Launcher! (https://www.rcuniverse.com/forum/electric-indoor-micro-rc-flight-182/4433291-storm-launcher.html)

Dave ESPI 12-08-2007 02:26 PM

RE: *!STORM LAUNCHER!*
 
The case and charger is so damn clean looking and handy though ! Just need to retro fit the jacks to it in a plane I think and I'll be good to go......

frednjess 12-08-2007 03:34 PM

RE: *!STORM LAUNCHER!*
 
The cases and assorted jacks add weight. Weight still = bad. But, I guess if you want to keep the cases you could jam a couple of banana clips in the input holes. Simplest way I can think of to make the case work.

ahaacobbler 12-10-2007 01:55 PM

RE: *!STORM LAUNCHER!*
 


ORIGINAL: Dave ESPI
Just wish the lipos from the SL's were compatable with other units.. I have 3 bats and 2 chargers now listed int eh RCU buyers section with some spare guts from a SL
I couldn't find the stuff you are selling. Could you please post a link? I don't suppose you are selling any motors or R/X boards?

My SL #3 is on its way from Spinmaster. I sure wish I had bought the SL with the TRU warrantee. The first and second stopped flying straight pretty quickly. Then I combined the 2 good motors from the first 2 in one fusalage and now one of those motors is weak too. I am told that the spinmaster is discontinuing the SL. I have to agree with their decision. The SL a lot of fun, but its hard to get much use out of one before it dies.

Cobbler.

trinogt 12-10-2007 09:21 PM

RE: *!STORM LAUNCHER!*
 
Mine lasted a good while. However, a few months of use followed by inevitable failure of the motors is not a good thing, at least when there are no replacement motors easily available.
In the rc hobby, the true hobbyists will fix and keep flying/driving, but when parts are not available, it gets impossible to do this.

Dave ESPI 12-11-2007 09:31 AM

RE: *!STORM LAUNCHER!*
 
http://www.rcuniverse.com/market/item.cfm?itemID=347848

I completely agree. If Spinmaster had made a press release as to where to get the motors ( or if they sold them) they could have saved themselves a lot of money, and also made a lot more offset repair cost.

cobalt jones 07-02-2009 09:44 PM

RE: *!STORM LAUNCHER!*
 
Hey, I'm new to RCU and haven't yet figured out how to start a forum thread. So I'll just jump in here incongruously and ask my question. I'm building a biplane of balsa and foam purely from my imagination and I don't see any good reason to have two elevator halves instead of just one long elevator. I don't like for example, on my Mini Funtana, how the one without the horn doesn't quite follow the other to the same degree. You can imagine the outcome of this inadvertant aileron in flight. So, why can't I just cut one piece of foam to look like two elevators, but actually be only one piece? In fact, I don't understand why it isn't done frequently on small electrics, to avoid the rear aileron syndrome aforementioned. Any comments or suggestions are invited. Particularly, suggestions on how to link a servo to an elevator of such span. I'm guessing I should simply treat it as I would an aileron, but I don't want the horn to fall left or right of center.

Dave ESPI 07-04-2009 01:39 PM

RE: *!STORM LAUNCHER!*
 
Cobalt, good luck ! not sure of your ability level, but there is a few other areas on this forum such as SCRATCHBUILDERS in foamies which will be better suited for your post.

CLICK " NEW THREAD" in one of the sections and then fillinthe blanks and hit OK.

HTH.
D/

cobalt jones 07-04-2009 04:16 PM

RE: *!STORM LAUNCHER!*
 
ok thanks


All times are GMT -8. The time now is 07:11 AM.


Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.