Go Back  RCU Forums > Electric Aircraft Universe > Electric Pattern Aircraft
Reload this Page >

Jeti Mezon/Himax 6330 Pro ESC settings

Notices
Electric Pattern Aircraft Discuss epowered pattern aircraft in this forum

Jeti Mezon/Himax 6330 Pro ESC settings

Old 05-24-2021, 04:21 PM
  #1  
luckymacy
Thread Starter
 
Join Date: Oct 2002
Location: Oklahoma City
Posts: 525
Received 1 Like on 1 Post
Default Jeti Mezon/Himax 6330 Pro ESC settings

It's been a few years since I used this motor and never with this ESC. Hopefully someone here can share their settings. If I recall, this is a 20 pole motor and I think I used to run this at PWM Rate 12kHz. What are all the Mezon brake and ramp related settings you like?
Old 05-24-2021, 07:04 PM
  #2  
flyboy91
My Feedback: (1)
 
Join Date: Feb 2002
Location: monroe, MI
Posts: 698
Likes: 0
Received 5 Likes on 5 Posts
Default

Originally Posted by luckymacy View Post
It's been a few years since I used this motor and never with this ESC. Hopefully someone here can share their settings. If I recall, this is a 20 pole motor and I think I used to run this at PWM Rate 12kHz. What are all the Mezon brake and ramp related settings you like?
Here should be some settings to get you close

Timing 24 degrees
Pole count 20
PWM 8Hz
Breakmanual
40% start power
brake delay 0.0
end power 60%
brake speed .1
Auto Cut off
3.0v per cell
Initial end point Auto
High end point 1.9
BEC voltage 8.0

Andrew
The following users liked this post:
luckymacy (05-25-2021)
Old 05-25-2021, 01:08 PM
  #3  
mallen2
 
Join Date: Jun 2006
Location: Norwich, UNITED KINGDOM
Posts: 1
Likes: 0
Received 0 Likes on 0 Posts
Default

Andrew, I'm curious with the selection of 0.1 brake speed does this mean you don't need any transition time between the 40% start and 60% end brake? Have I understood these settings correctly.

Mark
Old 05-25-2021, 02:10 PM
  #4  
flyboy91
My Feedback: (1)
 
Join Date: Feb 2002
Location: monroe, MI
Posts: 698
Likes: 0
Received 5 Likes on 5 Posts
Default

The .1 is the time it takes to go from 40% to 60% throttle. I have found that the .1 gives the right speed for the airplane to not build any speed on the downline.
Old 05-27-2021, 05:48 AM
  #5  
luckymacy
Thread Starter
 
Join Date: Oct 2002
Location: Oklahoma City
Posts: 525
Received 1 Like on 1 Post
Default

Originally Posted by flyboy91 View Post
Here should be some settings to get you close

Timing 24 degrees
Pole count 20
PWM 8Hz
Breakmanual
40% start power
brake delay 0.0
end power 60%
brake speed .1
Auto Cut off
3.0v per cell
Initial end point Auto
High end point 1.9
BEC voltage 8.0

Andrew
Did you experiment with a PWM value of 16? I think I used to use 16 with this motor.

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.