![]() |
3ch T-Hawk advice needed
Hi guys,
I have a Hanger 9 p41 pts that I don't feel like destroying just yet. So I picked up an electric 3 channel rtf T-Hawk to do my initial crash and burns. Comes with extra parts, I like that. Figured it would be a good plane to get some experince with. I have another electric 4channel I plan on going to next. Don't have many instructor options so this is going to be a self taught flying school for me. Any suggestions would be greatly appreciated. Anyone who's flown the T-Hawk that could give me some advice would be cool! Thanks, Steve |
RE: 3ch T-Hawk advice needed
Hi Steve, well I haven't flown the T-Hawk but I have flown quite a few like it, the plane should be pretty good about self righting itself so that will help, the biggest thing is don't try to fly in wind over 5 mph, for a while anyway, on most of these planes they will lift on there own with elevator set level but just a tad up is OK, just give it full throttle and a nice straight toss and it should climb out nicely
let it get to at least 100 ft before trying any turns, once there you can adj trims for level flight and just start with gentle turns making big circles, the Hawk should fly good at 1/2 to 3/4 throttle so I would try that once you get it up, this will slow down reaction time and make learning easier, also don't give full left ot right movment on the stick as that can cause it to spiral out of control, try to remember if you get into trouble let go of all the sticks and drop the throttle and it should self level itself, unless of course you have it in a bad spiral dive then it's 50 50 as to it catching itself. these planes are a lot of fun and fairly easy to fly. There are some mods you can do to strengthen the wing and secure the motor and tail boom, I don't know about the T-Hawk but the Fire Bird and AeroBird have issues with the motors pulling throught the fuse on nose crashes and the props eating the rear of the wing as well, Packing tape on the leading and trailing edge is a good idea for strength and protection from prop, If you are interested in other mods there is a whole thread on it called bullet broof that bird, you can use the search and pull it up and read through it, then decide for yourself what you think is needed Good Luck, I think you'll like the plane |
RE: 3ch T-Hawk advice needed
Thanks AJ1202! Kind of advice I was looking for.
|
RE: 3ch T-Hawk advice needed
Steve - I taught myself to fly with the T-Hawk. A very durable plane. It flys quite fast, so you need quite a bit of space for flying. When landing it likes to float forever - so plan on a long approach. With the stock battery and motor you can expect to fly for about 6-8 minutes. Like AJ said, if you get into trouble and you're high enough, back off the throttle and let the right stick center itself, the plane will right itself.
Happy Flying! Larry |
RE: 3ch T-Hawk advice needed
Great first plane! I recommend it often.
T-Hawk Discussion Thread http://www.rcgroups.com/forums/showt...ighlight=THawk Videos http://www.readytoflyfun.com/thawkvideos.html As for self training advice, I will follow with several posts. |
RE: 3ch T-Hawk advice needed
SIX KEYS TO SUCCESS
by Ed Anderson aeajr on the forums Whether you have a coach or you are trying to learn to fly on your own, you will need to be mindful of these six areas if you are going to become a successful RC pilot. After two years of working with new flyers at our club, and coaching flyers on the forums, there are a few things I have seen as the key areas to stress for new pilots. Some get it right away and some have to work at it. They are in no particular order because they all have to be learned to be successful. WIND Orientation Speed Altitude Over Control Preflight Check 1) Wind - The single biggest cause of crashes that I have observed has been the insistence upon flying in too much wind. If you are under an instructor's control or on a buddy box, then follow their advice, but if you are starting out and tying to learn on your own, regardless of the model, I recommend dead calm to 3 MPH for the slow stick and tiger moth type planes. Under 5 MPH for all others. That includes gusts. An experienced pilot can handle more. It is the pilot, more than the plane, that determines how much wind can be handled. The wind was around 10 mph steady with gusts to 12. That was strong enough that some of the experienced pilots flying three and four channel small electric planes chose not to launch their electrics. This new flyer insisted that he wanted to try his two and three channel parkflyers. Crash, Crash, Crash - Three planes in pieces. He just would not listen. Sometimes you just have to let them crash. There is no other way to get them to understand. Many parkflyers can be flown in higher winds by AN EXPERIENCED PILOT. I have flown my Aerobird in 18 mph wind (clocked speed) but it is quite exciting trying to land it. Always keep the plane up wind from you. There is no reason for a new flyer to have the plane downwind EVER! 2) Orientation - Knowing the orientation of your plane is a real challenge, even for experienced pilots. You just have to work at it and some adults have a real problem with left and right regardless of which way the plane is going. Licensed pilots have a lot of trouble with this one as they are accustomed to being in the plane. Here are two suggestions on how to work on orientation when you are not flying. Use a flight simulator on your PC. Pick a slow flying model and fly it a lot. Forget the jets and fast planes. Pick a slow one. Focus on left and right coming at you. Keep the plane in front of you. Don't let it fly over your head. FMS is a free flight simulator. It is not the best flight sim, but the price is right and it works. There are also other free and commercial simulators. FMS Flight simulator Home Page Free download http://n.ethz.ch/student/mmoeller/fms/index_e.html Parkflyers for FMS http://gunnerson.homestead.com/files/fms_models.htm The links below take you to sites that provide cables that work with FMS. If your radio has a trainer port, these cables allow you to use the trainer port on your radio to "fly" the simulator. This is an excellent training approach. http://www.allthingsrc.com/webshop/ http://www.simblaster.com/ http://www.customelectronics.co.uk/ An alternative is to try an RC car that has proportional steering. You don't have to worry about lift, stall and wind. Get something with left and right steering and speed control. Set up an easy course that goes toward and away from you with lots of turns. Do it very slowly at first until you can make the turns easily. Then build speed over time. You'll get it! If it has sticks rather than a steering wheel even better, but not required. Oh, and little cars are fun too. 3) Too much speed - Speed it the enemy of the new pilot but if you fly too slowly the wings can't generate enough lift, so there is a compromise here. The key message is that you don't have to fly at full throttle all the time. Most small electrics fly very nicely at 2/3 throttle and some do quite well at 1/2. That is a much better training speed than full power. Launch at full power and climb to a good height, say 100 feet as a minimum, so you have time to recover from a mistake. At 100 feet, about double the height of the trees where I live, go to half throttle and see how the plane handles. If it holds altitude on a straight line, this is a good speed. Now work on slow and easy turns, work on left and right, flying toward you and maintaining altitude. Add a little throttle if the plane can't hold altitude. 4) Not enough altitude - New flyers are often afraid of altitude. They feel safer close to the ground. Nothing could be more wrong. Altitude is your friend. Altitude is your safety margin. It gives you a chance to fix a mistake. If you are flying low and you make a mistake .... CRUNCH! As stated above I consider 100 feet, about double tree height where I live, as a good flying height and I usually fly much higher than this. I advise my new flyers that fifty feet, is minimum flying height. Below that you better be lining up for landing. 5) Over control - Most of the time the plane does not need input from you. Once you get to height, a properly trimmed plane flying in calm air will maintain its height and direction with no help from you. In fact anything you do will interfere with the plane. When teaching new pilots I often do a demo flight of their plane. I get the plane to 100 feet, then bring the throttle back to a nice cursing speed. I get it going straight, with plenty of space in front of it, then take my hand off the sticks and hold the radio out to the left with my arms spread wide to emphasize that I am doing nothing. I let the plane go wherever it wants to go, as long as it is holding altitude, staying upwind and has enough room. If you are flying a high wing trainer and you can't do this, your plane is out of trim. Even in a mild breeze with some gusts, once you reach flying height, you should be able to take your hand off the stick. Oh the plane will move around and the breeze might push it into a turn, but it should continue to fly with no help from you. Along this same line of thinking, don't hold your turns for more than a couple of seconds after the plane starts to turn. Understand that the plane turns by banking or tilting its wings. If you hold a turn too long you will force the plane to deepen this bank and it will eventually lose lift and go into a spiral dive and crash. Give your inputs slowly and gently and watch the plane. Start your turn then let off then turn some more and let off. Start your turns long before you need to and you won't need to make sharp turns. I just watch these guys hold the turn, hold the turn, hold the turn, crash. Of course they are flying in 10 mph wind, near the ground, coming toward themselves at full throttle. 6) Preflight check - Before every flight it is the pilot's responsibility to confirm that the plane, the controls and the conditions are correct and acceptable for flight. Plane - Batteries at proper power Surfaces properly aligned No damage or breakage on the plane Everything secure Radio - Frequency control has been met before you turn on the radio A full range check before the first flight of the day All trims and switches in the proper position for this plane Battery condition is good Antenna fully extended For computer radios - proper model is displayed All surfaces move in the proper direction Conditions - No one on the field or in any way at risk from your fight You are launching into the wind Wind strength is acceptable ( see wind above ) Sunglasses and a hat to protect your eyes All other area conditions are acceptable. Then and only then can you consider yourself, your plane, radio and the conditions right for flight. Based on your plane, your radio and local conditions you may need to add or change something here, but this is the bare minimum. It only takes a couple of minutes at the beginning of the flying day and only a few seconds to perform before each flight. If this all seems like too much to remember, do what professional pilots do, take along a preflight check list. Before every flight they go down the check list, perform the tests, in sequence, and confirm that all is right. If you want your flying experience to be a positive one, you should do the same. After a short time, it all becomes automatic and just a natural part of a fun and rewarding day. I hope some of this is useful in learning to fly your plane. |
RE: 3ch T-Hawk advice needed
PREFLIGHT AND FIRST FLIGHT PROCEDURES FOR PARKFLYERS
by Ed Anderson aeajr on the forums Here are some quick tips and a "check sheet" for preparing your parkflyer for launch. If you are a new pilot, you really need to heed the wind caution. If you are experienced, use your own judgment. Here is how you prepare for your first flights. Skip a step and you open yourself to problems. Respect the wind - For new pilots, dead calm to 3 MPH is perfect. No more than 5 MPH for early/training flights or you will be fighting the wind, not flying the plane. 1) Make sure no one is on your channel BEFORE you turn on your radio. If someone is flying on your channel and you turn on your radio, they will crash! Check first! 2) Do a range check before the first launch of the day 3) Make sure that battery is fully charged just before the launch. Not 3 days ago. Not last week. Last night or today! 4) Make sure all your surfaces are properly aligned and move properly before you launch. Check the manual if the surfaces do not appear to be properly aligned. Also make sure your wing is straight! 5) CHECK THE TRIMS! Check the trim slides on the side and below the stick(s). Be sure you have not bumped one out of position. A bumped trim can cause the plane to crash. Make sure the surfaces are properly alligned on the tail and the wings. 6) Always launch and land into the wind - ALWAYS 7) If you are hand launching, - good firm level throw or only very slightly up. Never throw the plane upward - Always use full throttle! 8) Let it fly out and gain speed. I would say a minimum of 50 feet, and 100 would be better. From a hand throw, it will drop a bit, that is OK. It should start to climb all on its own. If you use the elevator, only use a small amount. The plane must get up to speed before applying strong elevator. Apply the elevator too soon and you will "stall" the wing, the nose will drop and you will crash. IF THIS IS YOUR FIRST FLIGHT AND YOU ARE LEARNING ON YOUR OWN If your field will allow it, launch, fly out 100 feet or so then come back to about 1/4 throttle and let the plane drift down for a landing straight ahead. Just before the plane touches the ground, cut the motor. Use the rudder to keep it straight. Avoid turns. Do this a few times till you understand how the plane launches and lands. Then you can go for climbs and turns. I fly electrics and gliders. With my gliders, I ALWAYS do a test glide, with a hand throw, straight out then glide to the ground before launching off the hi-start or the winch. This confirms that the plane is balanced and everything works right. Good idea for electrics as well using that straight out launch, under power, then land. Saves much damage and embarrassment. If the plane is properly trimmed, it should climb on its own at full throttle or require only a small amount of up elevator. Use the elevator carefully! Unless you are going for a loop, use small elevator inputs. Too much up elevator with the plane flying too slowly will cause the nose to rise, the wing to stall and the nose to drop. Do this near the ground and you crash. Flight tips Keep your control movement smooth and don't over do it. Turn before you need to so you can give the plane time to react. This is called thinking ahead of the plane. Plan you moves. For three channel parkflyers that use rudder/elevator or two channels that only have rudder, don't hold rudder commands for more than a couple of seconds. On these planes, rudder commands will cause the plane to bank, or tip over in the direction of the turn. That is good because that is how they turn. However, if you hold the rudder too long, the bank will continue to steepen to the point where the wing will lose lift and you will go into a dive or spiral in for a crash. Of course you read the whole manual several times and watched any videos that might have come with the plane before you fly. Clear Skies and Safe Flying! |
RE: 3ch T-Hawk advice needed
I have read many posts about people who don't want to join a club for one
reason or another. I have found this especially common among new electric pilots because, for the most part, it is easier to go it alone with the electrics than with the fuel planes and sailplanes. You need less space, you need less equipment, the planes are typically small and quiet so you can go off by yourself and fly and in many cases no one will bother you. Net net, it is the people as much as the planes that have made this a wonderful experience for me. I have made many new friends, and perhaps an enemy or two. Yes, the club has restricted me in a few areas but they have expended my experience so much in others that, well, I can live with it. There are safety reasons, insurance reasons, instruction reasons and all sorts of other excellent reasons to join a club, but the main one is fun. The club has made a very enjoyable experience more fun than I could ever have imagined. If you had a bad club expereience, try a different club! If you are new to the hobby, I strongly suggest you seek out the clubs in your area. If you would like to see if there are clubs in your area, visit this link. Remember that the address shown for the club is usually NOT the flying field, but a member's house. In the case of our club, they are probably 20 mile apart. http://www.modelaircraft.org/templat...5E31DE4FA6F552 For other countries, use this link: http://www.fai.org/fai_members/addresses.asp Stop in and chat with the members. There is probably a club in your area that is made up of people who share your interests and who would richen your flying experience. Want to have more fun? Join a club! Clear skies and safe flying! |
RE: 3ch T-Hawk advice needed
During my pilot development I learned how hard it can
be to find a plane that has landed in the woods, tall grass and other places where you can't see it. Fortunately there are aids for this kind of situation. I lost my Aerobird when a huge gust of wind carried it over deep woods and I was too inexperienced to deal with it. Even though I was certain I knew where it went down I could not find it. I bought another Aerobird and fly it often. When I moved on to gliders I started flying a Great Planes Spirit 2 Meter. I got into trouble and it went down into heavy woods and brush. I went into the woods to find it. Fifty feet into the woods, trying to decide how to proceed since the area the plane went down could not be seen from a trail, I heard Beep Beep Beep. The plane was about 150 feet away in heavy tree growth. I had the plane located and out in 10 minutes. Believe me, where it had landed I likely would not have found it. The difference was a little device you put in the plane that gets attached to the receiver. If you turn off the transmitter, the thing starts beeping loudly and you can hear it from quite a distance. This is what I use in my Spirit Sailplane and several of my other planes. http://www.californiasailplanes.com/...l%20alarm.html It hooks to any channel or it can share a channel with one of your servos. It has the connector to pass through to the servo. This will work in any plane with a 72 MHZ receiver. This is the one I recommend to everyone. Low Voltage Watch In addition to helping me find the planes, the Digi Alarm also monitors my battery pack voltage and sounds an alarm if the pack voltage gets below a safe level. This is especially valuable on my glider. If I catch a good thermal, I could be in the air for over an hour, so a pack that tested good on the ground could run low during the flight. Channel Conflict Test! As a test to make sure no one is flying on your channel, turn on the receiver only. If the device does not go into lost plane mode then someone else is on your frequency. Here are five I have not tried, but look interesting. lost Model Locator - $10 Does one job, but does it well, I hope. http://www.allthingsrc.com/webshop/p...products_id/39 It is called the Be Found from GWS. - $15 http://www.gws.com.tw/english/produc...it/befound.htm SkyKing RC Lost Model Locator - $20 http://www.skykingrcproducts.com/acc...del_alarm.html Review http://www.slopeflyer.com/artman/pub...el_alarm.shtml RC Reporter - $24 A bunch of features http://www.rcreporter.com/products.html For 27mHZ planes like the Aerobird, Firebirds, etc My Aerobird does not have a conventional receiver that I can connect to. The electronics and servos are one integrated circuit board. No place to connect one of the above locators. On the Aerobird I use a key ringer. www.keyringer.com One of these on the plane and one stays in my pocket. If I am looking for the plane, I click the one in my hand and the one on the plane answers: Every plane I ever own will have some kind of locator and battery monitor from now on. Of course you only need one. You can move it from plane to plane, but at $15-30 they are cheap enough you can put one in every plane and forget it! For really long range finds, measured in miles, there is the Walston system. The plane unit is about $150 while the tracking unit is hundreds of dollars. This is good for clubs, especially sailplane clubs. If your sailplane costs $2000, a $150 transmitter is worth the cost. http://www.texastimers.com/helpful_h.../wal_cover.htm Here is a more complete article on the subject Lost Model Locators http://www.rcezine.com/cms/article.php?cat=&id=67 Many pilots don't know about these devices. Now you do! |
RE: 3ch T-Hawk advice needed
Thanks for all the replys guys. The winds appear to be very light to none today. If I can find the time I'm going to take the t-hawk out to my field and give her a try. It's on a big hill so the winds can be different from my house to the field so we'll have to see. About a hundred acres flat on the top that slopes off all directions on the edges. Kind of an ideal spot. Thinking I can be gaining altitude faster launching towards one of the slopes. I'll keep you posted on how it goes if indeed it does.
|
RE: 3ch T-Hawk advice needed
AEAJR, YOU ARE THE MAN! Thanks so much for all you do for us beginners, It is appreciated!
|
RE: 3ch T-Hawk advice needed
ORIGINAL: quando AEAJR, YOU ARE THE MAN! Thanks so much for all you do for us beginners, It is appreciated! |
| All times are GMT -8. The time now is 03:21 PM. |
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.