3 Rates for 10C?
#1
3 Rates for 10C?
You did'nt like the way I worded this before so I will try it a little differently.
The Futaba 9C has the ability to have their 2-position rate switches (airlon, elevator, and rudder) changed out for 3-position switches. Does the 10C share this configuration; is it's circuitry similar to the 9C in this respect?
The Futaba 9C has the ability to have their 2-position rate switches (airlon, elevator, and rudder) changed out for 3-position switches. Does the 10C share this configuration; is it's circuitry similar to the 9C in this respect?
#2
Join Date: Jan 2003
Location: Champaign, IL
Posts: 3,796
Likes: 0
Received 0 Likes
on
0 Posts
RE: 3 Rates for 10C?
If you would like to send your 10C into our service center, we will change out your 2 position switches for you to the 3-position switches.
Sincerely,
Krysta
Product Development & Support Specialist
Futaba Service Center USA
[email protected]
Sincerely,
Krysta
Product Development & Support Specialist
Futaba Service Center USA
[email protected]
ORIGINAL: hilleyja
You did'nt like the way I worded this before so I will try it a little differently.
The Futaba 9C has the ability to have their 2-position rate switches (airlon, elevator, and rudder) changed out for 3-position switches. Does the 10C share this configuration; is it's circuitry similar to the 9C in this respect?
You did'nt like the way I worded this before so I will try it a little differently.
The Futaba 9C has the ability to have their 2-position rate switches (airlon, elevator, and rudder) changed out for 3-position switches. Does the 10C share this configuration; is it's circuitry similar to the 9C in this respect?
#3
My Feedback: (2)
Join Date: May 2008
Location: Norfolk,
MA
Posts: 289
Likes: 0
Received 0 Likes
on
0 Posts
RE: 3 Rates for 10C?
This is an interesting question, and while we are on this subject, I have a follow-up... If one was to send it in and have switches changed to 3-position, would the software side of the 10C recognize the change. My curiosity is in respect to the 3-pos switch we currently have on the 10C, the software automatically recognizes that you have (ex. moved flaps to a 3-pos. switch) changed the assignment of the switch to a 3-pos. from, say, a knob. Will this change in replacing other 2-pos. switches do the same w/ respect to the assignment automatically recognized as a 3-pos. selection/feature/capability?
Thank you in advance.
- Don
Thank you in advance.
- Don
#4
Join Date: Jan 2003
Location: Champaign, IL
Posts: 3,796
Likes: 0
Received 0 Likes
on
0 Posts
RE: 3 Rates for 10C?
Hi Don,
Yes, we have the capability here in the Service center of formatting the software to recognize the changes in the switch. This is why a customer must send this into us to have this done.
Sincerely,
Krysta
Product Development & Support Specialist
Futaba Service Center USA
[email protected]
Yes, we have the capability here in the Service center of formatting the software to recognize the changes in the switch. This is why a customer must send this into us to have this done.
Sincerely,
Krysta
Product Development & Support Specialist
Futaba Service Center USA
[email protected]
ORIGINAL: fishingships
This is an interesting question, and while we are on this subject, I have a follow-up... If one was to send it in and have switches changed to 3-position, would the software side of the 10C recognize the change. My curiosity is in respect to the 3-pos switch we currently have on the 10C, the software automatically recognizes that you have (ex. moved flaps to a 3-pos. switch) changed the assignment of the switch to a 3-pos. from, say, a knob. Will this change in replacing other 2-pos. switches do the same w/ respect to the assignment automatically recognized as a 3-pos. selection/feature/capability?
Thank you in advance.
- Don
This is an interesting question, and while we are on this subject, I have a follow-up... If one was to send it in and have switches changed to 3-position, would the software side of the 10C recognize the change. My curiosity is in respect to the 3-pos switch we currently have on the 10C, the software automatically recognizes that you have (ex. moved flaps to a 3-pos. switch) changed the assignment of the switch to a 3-pos. from, say, a knob. Will this change in replacing other 2-pos. switches do the same w/ respect to the assignment automatically recognized as a 3-pos. selection/feature/capability?
Thank you in advance.
- Don
#5
My Feedback: (2)
Join Date: May 2008
Location: Norfolk,
MA
Posts: 289
Likes: 0
Received 0 Likes
on
0 Posts
RE: 3 Rates for 10C?
Krysta,
Thank you very much for your timely and excellent response! That is awesome that it can be done to the s/w as well as h/w and I will probably be doing the same as hilleyja (i.e. sending in to Futaba Service for the change/upgrade. I would hope Futaba's marketing group is onto this as well, since it nay be a feature in which your competition can not meet !!!
Again, thank you so much for your help... and I LOVE my 10C !
Fond Regards,
- Don
Thank you very much for your timely and excellent response! That is awesome that it can be done to the s/w as well as h/w and I will probably be doing the same as hilleyja (i.e. sending in to Futaba Service for the change/upgrade. I would hope Futaba's marketing group is onto this as well, since it nay be a feature in which your competition can not meet !!!
Again, thank you so much for your help... and I LOVE my 10C !
Fond Regards,
- Don