AJT

Just ordered one of these bad boys for my new DIETRICK 50cc EXTRA 260. I will be running a MTW 75 can and DA header, VESS 23A. for break in...

Thanks Larry I''ll keep you posted.
AL

mistydee0

My Feedback: (103)

AJT,
Your engine is going out in the morning.

Larry LS PRO ENGINES

AJT

Gotta love that service!!

bigbuster

My Feedback: (12)

Got mine today, which was a surprise. Thanks Mistydee



I need to et her mounted on my bipe now.




Thanks
Jeff

bigbuster

My Feedback: (12)

Is their an instruction manual online someplace? If not what are the 2 nipples on the carb for?


Jeff

soarrich

My Feedback: (98)

You got the girly one!


One''s for fuel the other is for the pressure pulse from the crankcase.

bigbuster

My Feedback: (12)

The girly one put a huge smile on my face. Good sense of humor soarrich.



Jeff

3DNutZ

Are there any reports on this engine??

pianori

My Feedback: (2)

Thre are some numbers, facts and videos at this site. Take a look at it.
[link]http://www.rcuniverse.com/forum/m_7279596/anchors_7457552/mpage_5/key_/anchor/tm.htm#7457552[/link]

GMoneyPit

My Feedback: (5)

AJT,

Any word on your Dietrick/MT57 combo? I'm interested in the same combo and would really like to hear how yours is doing.

Gary

closetguy

My Feedback: (13)

this is what i got out of mine,with a MTW pipe, 11" header.pennzoil 32-1 and 1.5 gallons through it.
Vess 23-A 7200
Mejzlik 23-8 6900
Bolly 23-8 6900
Beila 24-8 6400

orlandito33

is a problem with the mt57.after every fl check the engine gasquet

Hughes500E

My Feedback: (16)

HUH?

karmann34

My Feedback: (5)

Edited:
I accidently Posted in wrong thread. doh!

Mr_Grump

The MT-57 is my first engine that requires drilled props. Any suggestions on a drill guide? How about offering one Larry?

Thanks

Lane

Super08

My Feedback: (2)

It uses a ZDZ drill pattern. PSP makes a drill guide that works well.

skip1320

It is same as DL/DA 100

Super08

My Feedback: (2)

True, but with 4mm holes not 5mm holes. That is why I got the ZDZ drill jig.

skip1320

Good point i forgot,thanks

Mr_Grump

Thanks a lot guys. I've got one on order...

Lane

MartyH

My Feedback: (16)

Any long term reports from someone flying the MT57 for the past year or so? We keep referencing the old prop tests. How is it holding up and who all supports this engine these days. I'm between this engine and the DLE-55.

Hughes500E

My Feedback: (16)

I'm at the end of the second season with mine. It starts on the third flip each time and positive comments are still heard when I'm flying. I recommend the MT75K canister as it was equal to a tuned pipe for numbers. I have experienced zero problems with my engine, I would like to buy an MT-80

I have never had to funk with my needles and I always receive consistent power! I hope my DA85 runs as reliable as my MT57.

Mine has been a great purchase.

mtenginesusa

MT are upgrade MT57 to the new level . it's MT70CC twin . about $ ?79

Hughes500E

My Feedback: (16)

I'll bite, at just over 3Lbs for a 70 twin, are you saying we are going to have a 30 as well?

Impressive!

MetallicaJunkie

pretty close to the dl50 based on some peoples numbers....i got about 6700 on a 23x8 xoar