EME 35/ EME 60 released
1 Attachment(s)
Hello all,
EME 35/ EME 60 are available now. The engines are sending to dealers worldwide and come to market soon. EME 35 relative pics are as follows. |
RE: EME 35/ EME 60 released
1 Attachment(s)
EME60 relative pics are as follows. |
RE: EME 35/ EME 60 released
1 Attachment(s)
<div id="post_message_1767743">There aretest scratches and videos.
Kinds of engines and mufflers are tested, including the tuned pipe for 50~60cc. All of them are made by EME. For EME 60, Drive 23*10 Xoar Prop @ 6450 with stock muffler, still rich set Drive 24*8 Xoar Prop more than 6600 RPM. For EME 35, Drive 19*8 Xoar Prop @ 7550~7600 with stock muffler, still rich set Drive 20*8 Xoar Prop more than 7100 RPM. Videos http://www.youtube.com/watch?v=vgetx...ature=youtu.be http://www.youtube.com/watch?v=E_DsDu3TMts Moreover, dealers are still wanted. Pls contact [email protected] </div><! / message ><! attachments > |
RE: EME 35/ EME 60 released
1 Attachment(s)
Moreover, some design details are as follows,
|
RE: EME 35/ EME 60 released
Send pic,s of that tune pipe stuck in wall behind 35,thanks
|
RE: EME 35/ EME 60 released
ORIGINAL: emengines Moreover, some design details are as follows, |
RE: EME 35/ EME 60 released
HOW SOON, HOW MUCH, HOW POWERFULL, HOW RELIABLE, HOW HEAVY, & WHO IS SELLING THEM...There, all we need to know!
|
RE: EME 35/ EME 60 released
ORIGINAL: tande ORIGINAL: emengines Moreover, some design details are as follows, |
RE: EME 35/ EME 60 released
1 Attachment(s)
ORIGINAL: skip1320 Send pic,s of that tune pipe stuck in wall behind 35,thanks It is for 50~60cc single or 100~120 twin. A monster. |
RE: EME 35/ EME 60 released
1 Attachment(s)
ORIGINAL: tande ORIGINAL: emengines Moreover, some design details are as follows, |
RE: EME 35/ EME 60 released
1 Attachment(s)
Hi Jeame,
on the 35cc what is the distance from the back of the solid mount to the low mixture screw? I'm asking as I was curious to see if it's possible to mount the engine without stand offs to the firewall and still have acess to the mixture screws. Naurally a big hole in the firewall would be needed for the carb. Also what is the distance from the back of the solid mount to the front of the prop hub? |
RE: EME 35/ EME 60 released
Hello,3136
It is possible to adjust the needle without stands if the firewall is less than 10mm Pls check the dimention of EME 35 as link below, http://www.emehobby.com/download_en.asp Best Regards |
RE: EME 35/ EME 60 released
I have been watching EME for about two years now and have been impressed with the improvements. I just ordered a 120 to try this year from the distributor here in Canada, Thunderbolt RC.
|
RE: EME 35/ EME 60 released
Is anyone in the US selling and carry parts for the EME engine? I bought mine from Taildragger and they do not carry them anymore. Thanks
|
RE: EME 35/ EME 60 released
If you cannot find any Thunderbolt RC in Canada does.
|
RE: EME 35/ EME 60 released
ORIGINAL: TunnelBill Is anyone in the US selling and carry parts for the EME engine? I bought mine from Taildragger and they do not carry them anymore. Thanks DaleD <br type="_moz" /> |
All times are GMT -8. The time now is 10:37 PM. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.