RE: Extreme Flight 88" Yak - Build and Fly
 

I figured some folks might use the Klett 3/16" axles which have a very small axle base, so the hole in the gear is small.

RE: Extreme Flight 88" Yak - Build and Fly
 

Does the hardware pack include axles ?

RE: Extreme Flight 88" Yak - Build and Fly
 

The hardware pack has everything BUT axles, wheels and collars.

RE: Extreme Flight 88" Yak - Build and Fly
 

Ok..Ill have to pick some up...

RE: Extreme Flight 88" Yak - Build and Fly
 

Where can you get the Klett axles at??

RE: Extreme Flight 88" Yak - Build and Fly
 

Not sure Boss, probably from Goldberg/Lanier. They are marketing a lot of the old Klett hardware.

RE: Extreme Flight 88" Yak - Build and Fly
 

Here's some:

http://www.acornmodels.co.nz/product.php?prod=2880

RE: Extreme Flight 88" Yak - Build and Fly
 

O.K., dropped the template on the firewall and drilled for the Brilleli 60...

The cowl SWALLOWS this engine! (Like we expected) :)

It's hard to tell fromthe pics... but there is a full 1" between the velocity stack and the cowl side... and about 3/4" below the spark plug...

SO there MAY or MAY NOT be a need for a slot to be a slot made for the spark plug boot... The DA50 stock muffler I'm using will only need a hole for the stack cut... nothing for the can itself...

I'm starting to think the fake louvers aren;t such a bad idea... :)

RE: Extreme Flight 88" Yak - Build and Fly
 

Dave, Is a fuel tank and stopper included with the hardware kit?

RE: Extreme Flight 88" Yak - Build and Fly
 

Yep tank and gas compatible stopper... but I already made up a 16 oz DUBro...

RE: Extreme Flight 88" Yak - Build and Fly
 

Have you heard any input from Scott E. or Aerobob about fuel burn with the 366GT? Will 16oz be enough for a 14-15min flight or should I use a 20oz tank?

RE: Extreme Flight 88" Yak - Build and Fly
 

It's official... I will no longer be applying G-Glue to the hingepoints.. just in the hole (I used to do both).

Two reasons...

1) Less foam comes out near the knuckle (almost none actually) because the hinge pushes the glue into the hole, the hole doesn't scrape glue off the hinge

2) 5 different tests doing it that way either busted the hingepoint at the knuckle trying to pull it out... or I simply didn't have enough strength to pull it out myself.

(the loose end of the hingpoint in a vise... and me pulling the wood away from the hinge)

Awsome...

So now the steps will be:

Swap the holes of the trailing edge and the surface with a wet q-tip

Start with the trailing edge of a surface and apply a couple drops to each hole with a bamboo skewer poking and twirling it so it's fully coated the hole
Insert hingepoint that has had the knuckle dipped in melted vaseline

Then glue up the surface holes and slide it onto the hinges...

Tape the suface in place...

Occasionally wiping any foaming away and flexing the surface to make sure the hinges remain free...

RE: Extreme Flight 88" Yak - Build and Fly
 

Tank and stopper are included, just not in David's. Hadn't arrived when I shipped yours David, sorry[:o]

RE: Extreme Flight 88" Yak - Build and Fly
 

I just spoke with Scott at Brillelli... eh said he thought maybe a 20 oz tank would be better... he will test it at 3/4 throttle...

My DA50's run 20 mins+ for sure... but 10cc's more...

RE: Extreme Flight 88" Yak - Build and Fly
 

That's it... I want a refund!!!!!! :)

NP... I almost ALWAYS use a 16 oz DUBro anyway...

RE: Extreme Flight 88" Yak - Build and Fly
 

Eagle Pilot... see my edited repsonse above... Scott says maybe a 20 oz tank would be better... he's gonna test...

He also said that pnce the spark plug boot is on there should still be 1/4" clearnace... meaning we mioght not have to cut for the sprak plus boot after all! :)

RE: Extreme Flight 88" Yak - Build and Fly
 

I know with my DA 50's I could fly about 13 min on a 16oz tank with about 1/4 left in reserve...Do we get a 20 or a 24oz tank ?

RE: Extreme Flight 88" Yak - Build and Fly
 

I would test it right away, but I have no 60's built right now. I sent the last 3 out to future EF Yak owners :) I do not think the 60 will use much more fuel than the DA 50 so I am betting it will be fine with a 16oz tank. I just would like to test it to be sure. Too many tasks, too little time !

RE: Extreme Flight 88" Yak - Build and Fly
 

I have a 16oz Dubro onhand, so I'll try a 20oz. But if the 20oz runtime is too long, I'll switch back to the 16oz rather than carrying around an excess amount of gas.

Also, I've experienced an appreciable increase in fuel burn when switching from an in cowl muffler to a tuned pipe setup on the same engine [sm=wink_smile.gif]

RE: Extreme Flight 88" Yak - Build and Fly
 

wow

RE: Extreme Flight 88" Yak - Build and Fly
 

Here is the gear that will be on my 88" Yak. 6.6 OZ and without a doubt the best built, most stock looking gear I have ever seen. It's even airfoiled. They ain't cheap! Mine will be painted white as I'm getting the red and white plane. I suppose you guys with the black planes would just leave it black

john

RE: Extreme Flight 88" Yak - Build and Fly
 

Whats the price of the CF gear?

RE: Extreme Flight 88" Yak - Build and Fly
 

I am pretty sure I fly 15-20 mins on a 24oz tank and usually have about 1/3 left.. but that is lots of full speed KE circles and rollers. I think you could get away with a 16oz tank.

RE: Extreme Flight 88" Yak - Build and Fly
 

And I'll do just the opposite... I'll test the 16 oz and if it's not enough, I'll step up... ;) (already have the 16 oz tank made up)

RE: Extreme Flight 88" Yak - Build and Fly
 

ALl hinged... man it takes NO time when yo don't have to try and coat the actual hingepoints... which most of it gets scraped off by the hole anyway and into the bevel/knuckle for cleanup...

Much cleaner this way and faster... lovin' it!

Now if my ailerons go flying inthe air one day.....


Seriosuly... I think the plane will have to blow up before the surfaces come off...