RE: Peak Model 50 CC Edge 540 T build
Yes T3, Thanx.
I was traveling and so could not reply. |
RE: Peak Model 50 CC Edge 540 T build
ORIGINAL: Eganwp Haha at our field we have 8 of 8 DLE 55's that have deadsticked, I kid you not. I've flown at a couple other fields and same story. People here hate them... lol. To really hit it home, I watched a 35% bird go in and was a total write-off Wed. night from a low end deadstick 111, and my good buddy totalled off his 30% Pilot Yak on a 55 deadstick in a 20ft hover thursday night at our field this week... I've also never talked to DLE 111 owner who hasn't had a deadstick either. . Good times! On that note, after changing the metering height of my carb main jet arm, it made no difference. That was the last resort as I've exhausted over 20+ things/setups/etc and had WAY too many gas guys and engine guru's try and fix the engine. Enough was enough, so I threw on a brand new carb and new ignition on thursday after the 5th deadstick. Whalla! I haven't had a single deadstick or engine skip at all with the new gear! :D I'll be flying in my first IMAC competition tomorrow with this bird! Wish me luck! :) Egan |
RE: Peak Model 50 CC Edge 540 T build
Nah, every DLE owner at our clubs in Calgary run CM-6 plugs that I've talked to. 2 of the guys have gone through 2+ ignitions I also discovered the other day. All are running on Stihl, Opti2, Redline or BelRay H1R synthetic and all have tuned their carbs from day 1. Oh well, don't matter. So I got fed up after the last DS, and tossed on a brand new carb and ignition. This carb runs MUCH better. Both needles tune where they should (IE low speed 1 1/4 out rather than less than 3/4 out on the old one fully tuned). Engine ran perfectly and didn't skip a beat in all 16 sequences. Was glad to hear that for once!
So I actually did really well in my first IMAC competition this weekend. Ended up winning 1st place in Basic!! :) Was soooo much fun, so glad we went. Won a new 40 sized Extra 300s, a trophy and a bunch of other little things. Had a blast. Can't wait for the next competition though I'm afraid I may have to move up to Sportsman as the judges told me I need to move up, so we'll see. Scored 1,000 on every sequence after normalization, but I still need to work on a few little things like better cross-wind correction. The funniest thing happened in round 5. It was 35+ km/h wind and I went for the final manouver, 1 1/2 stall spin. The plane slowed down all the way with full elevator deflection but wouldn't stall because of the straight leading edge like most of the rounds. The plane ended up flying backwards until I forced the stall and the judges were all laughing! Was a sight to see! hahaha. Anyone on the edge thinking about going into IMAC definately should try it out. The people are awesome, you'll get a lot of experience, your flying will improve immensely and you'll have a blast! |
RE: Peak Model 50 CC Edge 540 T build
Great Job Eganwp! Having fun is what its about. Sorry guys no vid yet of my edge. Work, weather,and flying sites are all out to keep this bird grounded for now.
Hey johns3d, I just ordered the peak sbach300. What was your all up weight? Going to use a Turnigy HP26S ( this motor is actually 32cc and has been uppgraded to reed valves). |
RE: Peak Model 50 CC Edge 540 T build
Hey 49 even I have a 30cc DLE waiting for sbach300 from cyclone. It will be nice if you post your build.
Cheers.. Sandy jain |
RE: Peak Model 50 CC Edge 540 T build
Will do sandy. johns3d has a build thread started on the peak model sbach 300 and i will post it there when it arrives.http://www.rcuniverse.com/forum/js/f...wink_smile.gif
|
RE: Peak Model 50 CC Edge 540 T build
Sweet guys! Keep us posted on the 30cc. My next build is going to be a 30cc MX2 I think! :D Now, if only I could find a CF gear version....
|
RE: Peak Model 50 CC Edge 540 T build
ORIGINAL: Eganwp Sweet guys! Keep us posted on the 30cc. My next build is going to be a 30cc MX2 I think! :D Now, if only I could find a CF gear version.... |
RE: Peak Model 50 CC Edge 540 T build
1 Attachment(s)
ORIGINAL: Eganwp Landing gear redesign pics!!! So much stronger, and easily accessible than the stupid stock setup. CF gear is from GraphTech (QQ Yak 88" gear w/ forward rake) Enjoy. :D Egan See ya in September! |
RE: Peak Model 50 CC Edge 540 T build
ORIGINAL: Eganwp Sweet guys! Keep us posted on the 30cc. My next build is going to be a 30cc MX2 I think! :D Now, if only I could find a CF gear version.... Also cyclonetoy.com has some versions with CF upgrades. Specially the Sbachs. Cheers.. Sandy |
RE: Peak Model 50 CC Edge 540 T build
Finally got some videohttp://www.youtube.com/watch?v=sjOl2zKPosQ. You guys still flying yours?
|
RE: Peak Model 50 CC Edge 540 T build
Windy day! How do you like it?
|
RE: Peak Model 50 CC Edge 540 T build
Have Stabs/elevators,1 wing,rudder,tubes,landing gear for this plane if any interested,looks good Dimes!
|
RE: Peak Model 50 CC Edge 540 T build
Flies like a foamy! The wind rocked it like a foamy as well. I ambegining to wonder if we are ever going to get a calm day. @%$#&*&% wind been blowin all year long in the 15 to 30 range. If I can get a decent day I will get some vid and grass stains on the rudder.
ORIGINAL: T3beatz Windy day! How do you like it? |
RE: Peak Model 50 CC Edge 540 T build
Got some pics of the left overs?
ORIGINAL: skip1320 Have Stabs/elevators,1 wing,rudder,tubes,landing gear for this plane if any interested,looks good Dimes! |
RE: Peak Model 50 CC Edge 540 T build
Yep, still flyin mine!
|
RE: Peak Model 50 CC Edge 540 T build
Great egan! I am really likin this bird. The only negative I have found is the short wing tube and wing flex. I did a high-G figure eight and almost popped some ribs. It looked as if it had a huge amount of dihedral with moderate g force applied. Will have to keep this airframe slowed down. Here is some more vid. Also Merry Christmas to all and hope your R/C dreams come true. http://www.youtube.com/watch?v=UJphPkzgMZA<u><font color="#810081">http://www.youtube.com/watch?v=-LjwkI8DoT8</font></u></p> |
All times are GMT -8. The time now is 07:21 PM. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.