Fleet Brotherhood
#429
Thread Starter
My Feedback: (18)
RE: Fleet Brotherhood
Pardon my ignorance Hank, but what is F/M?
If the front moves through Florida before the weekend and takes the winds with it, it looks like Saturday or Sunday for my maiden flight. I had my first crash yesterday while attempting to range check my Tx/Rx. I placed the Fleet in the driveway, retrieved my Tx from the garage and the pilot released the brakes. The Fleet went rolling down the incline, crossed the street and banged into the curb. No damage, as it hit on the wheels. As I saw it start to roll all I could envision is a car coming down the street and squashing it. I gave the pilot a verbal reprimand.
Seems RCU isn't notifying me of updates to the Brotherhood as it used to. I have to occasionally check in to see what's new.
Bob
If the front moves through Florida before the weekend and takes the winds with it, it looks like Saturday or Sunday for my maiden flight. I had my first crash yesterday while attempting to range check my Tx/Rx. I placed the Fleet in the driveway, retrieved my Tx from the garage and the pilot released the brakes. The Fleet went rolling down the incline, crossed the street and banged into the curb. No damage, as it hit on the wheels. As I saw it start to roll all I could envision is a car coming down the street and squashing it. I gave the pilot a verbal reprimand.
Seems RCU isn't notifying me of updates to the Brotherhood as it used to. I have to occasionally check in to see what's new.
Bob
#430
Join Date: Jun 2012
Location: JOSHUA,
TX
Posts: 181
Likes: 0
Received 0 Likes
on
0 Posts
RE: Fleet Brotherhood
F&M ENTERPRISES.COM. PHONE 817- 279 - 8045. GRANDBURY, TX. Look at their web site Bob. SORRY to hear about your mis hap in driveway. Yes I am having trouble with R C U . HANK # 20
#431
Join Date: Jun 2012
Location: JOSHUA,
TX
Posts: 181
Likes: 0
Received 0 Likes
on
0 Posts
RE: Fleet Brotherhood
send for the vido Bob. Ask for the sample pack. Balsa u s a sells the poly tack much cheaper. You will find this cover goes on very good and strong. Hank # 20 .
#433
RE: Fleet Brotherhood
Well Bob, looks like we won't be making the Deland Fly-in. Motor was good and strong but a case of dumb thumbs in the sun and ...
What a dust cloud it threw up. Picking up the pieces was the easy part as the landing and flying wires all held it to one heap. Sadly, the pilot was ejected from the cockpitand was hanging in his shoulder belts.
The very long walk back was made longer by having to traverse a small irrigation ditch that turneddeeper as I stood in it.
Bird is repairable but it will take some time.
I still plan to take in some grandchild time so we may drag her brothers over to the show and meet you face to face.
Ray W.
What a dust cloud it threw up. Picking up the pieces was the easy part as the landing and flying wires all held it to one heap. Sadly, the pilot was ejected from the cockpitand was hanging in his shoulder belts.
The very long walk back was made longer by having to traverse a small irrigation ditch that turneddeeper as I stood in it.
Bird is repairable but it will take some time.
I still plan to take in some grandchild time so we may drag her brothers over to the show and meet you face to face.
Ray W.
#435
Join Date: Jun 2012
Location: JOSHUA,
TX
Posts: 181
Likes: 0
Received 0 Likes
on
0 Posts
RE: Fleet Brotherhood
!! OK !! One of the fleets is strip dwn. CKed all glue joints . F/W alumminum trianglemount bolts have rusted out over the year's. Landing gear bolts threads have rusted out. Wheels need to be replaced. Aluminum tonques have to be replaced. mounting holes are strip. HANK #20.
#436
Join Date: Jun 2012
Location: JOSHUA,
TX
Posts: 181
Likes: 0
Received 0 Likes
on
0 Posts
RE: Fleet Brotherhood
# 2 Wings are in good shape. NO warpage . Stab & elev. need replacment ( warpaage ). Windshield glass & intrument panel ( replaced ). All servoes need replacement. This fleet had a S/T 3000 mounted. HANK 20
#439
RE: Fleet Brotherhood
Yup Hank, she is repairable but with lots of long term as I've some other planes to finish before hand. I can get my other larger Fleet ready for a Spring maiden so that is first. Now, seeing as I was rather rusty at the sticks, I may finish off an already framed up BUSA L-4 just waithing for covering and my new Saito 150.
I went in the trailer and sorta looked the ole bird over and see that un-cover and repair of the front ot the fuse is in order. Maybe , that will be the best time to redo the color scheme as well.
Hoping to be hearing some good news from Retransit soon.
Ray W.
I went in the trailer and sorta looked the ole bird over and see that un-cover and repair of the front ot the fuse is in order. Maybe , that will be the best time to redo the color scheme as well.
Hoping to be hearing some good news from Retransit soon.
Ray W.
#440
Thread Starter
My Feedback: (18)
RE: Fleet Brotherhood
My Fleet completed its maiden today. Weather was just about perfect with virtually no wind except for a small quartering cross. Anyway, I had a buddy of mine do the initial because I was shooting the video and I wimped out. He was good enough to do it. Excellent pilot.
I finished the flight off, doing a loop and then landing about a minute later. Total airborne time was about ten minutes. I had about a third of a the 32 oz. tank left after shutdown. I have to shim the right rear cabane to get the leading edge to drop some positive incidence. It had a tendencey to roll left on takeoff. I also have to place another shim under the horizontal stab leading edge, as it wants to climb when increasing power. Everything else is OK and the engine ran beautiful. Must have been that little adjustment toward lean on the low speed needle. It had absolutely no tendency to drop a cylinder upon increasing power without the glow driver engaged. I finally did something right! it was peaked at 6150 rpm with a 20-10 Xoar prop.
Here are a few pictures taken at the field and the video.
Bob
[youtube]http://www.youtube.com/watch?v=gbZxPgdZMBU[/youtube]
I finished the flight off, doing a loop and then landing about a minute later. Total airborne time was about ten minutes. I had about a third of a the 32 oz. tank left after shutdown. I have to shim the right rear cabane to get the leading edge to drop some positive incidence. It had a tendencey to roll left on takeoff. I also have to place another shim under the horizontal stab leading edge, as it wants to climb when increasing power. Everything else is OK and the engine ran beautiful. Must have been that little adjustment toward lean on the low speed needle. It had absolutely no tendency to drop a cylinder upon increasing power without the glow driver engaged. I finally did something right! it was peaked at 6150 rpm with a 20-10 Xoar prop.
Here are a few pictures taken at the field and the video.
Bob
[youtube]http://www.youtube.com/watch?v=gbZxPgdZMBU[/youtube]
#441
Join Date: Jun 2012
Location: JOSHUA,
TX
Posts: 181
Likes: 0
Received 0 Likes
on
0 Posts
RE: Fleet Brotherhood
HO RA!!!!. MY FLEET # 7 TOOK TO THE AIR.aFTER A FEW TRM ADJUSTMENT'S. SHE FLEW BEAUTIFUL. lANDINGWAS A BIT (HAIRY ). COULDN'T GET THE IDLE DWN, TO FLAIR OUT. SO FAR 6 FLIGHTS. HAVE TO CK. SERVO LINGAGE ?. 4 OF MY FRIENDS HAD THEIR WAY WITH HER. ALL WENT WELL , EXCEPT FOR THE IDLE. NEXT TIME I WILL USE THE BALLON TIRES FOR THE GRASS. HANK # 20 .
#443
Join Date: Jun 2012
Location: JOSHUA,
TX
Posts: 181
Likes: 0
Received 0 Likes
on
0 Posts
RE: Fleet Brotherhood
THANK'S BOB. TODAY WAS A GREAT DAY. HOPE THE EASTER BUNNY BRING'S ME A NEW COMPUTOR. SO! I CAN SEND PHOTO'S . GLAD TO HEAR YOUR DAY WENT WELL. HANK # 20.
#446
Member
Join Date: Jan 2009
Location: Cocoa,
FL
Posts: 46
Likes: 0
Received 0 Likes
on
0 Posts
RE: Fleet Brotherhood
Sorry to hear Ray. Still hope you can make it down. I'm going to try to be there.
Nice to meet ya Hank.
Bob, I finally have my Fleet in my shop.
Looks to have been covered w/Solartex.
I think Im going to peel the bottoms off of each piece for inspection and gluing.
Still taking down computer animated Christmas light display first.
Will bring it to the show for static display.
Cliff
Nice to meet ya Hank.
Bob, I finally have my Fleet in my shop.
Looks to have been covered w/Solartex.
I think Im going to peel the bottoms off of each piece for inspection and gluing.
Still taking down computer animated Christmas light display first.
Will bring it to the show for static display.
Cliff
#448
RE: Fleet Brotherhood
Bob,
Got my wings covered and pinked tape done...
On the Concept Fleet thread you installed simulated screw heads on the wing/taping and I'm thinking about giving it a try. Did I recall that you used epoxy? I did some tests of Elmers wood glue, canopy glue and epoxy, and the epoxy seemed to work best. The problem seems to be to get a consistent size drop. Any hints on this?
Dave
Got my wings covered and pinked tape done...
On the Concept Fleet thread you installed simulated screw heads on the wing/taping and I'm thinking about giving it a try. Did I recall that you used epoxy? I did some tests of Elmers wood glue, canopy glue and epoxy, and the epoxy seemed to work best. The problem seems to be to get a consistent size drop. Any hints on this?
Dave
#449
Thread Starter
My Feedback: (18)
RE: Fleet Brotherhood
I used a stick of balsa with a pin inserted into it. The stick is just something to hold the pin while you dip the pin head in white glue (Elmers, Titebond, etc.) Map out your spacing with a pencil and start. Mistakes can be easily wiped off or picked off when dry.
I've used a syringe in the past, but the pin works better for me.
Check out this video I made:
http://www.youtube.com/watch?v=b1xYF...e-nzQ&index=20
Bob
I've used a syringe in the past, but the pin works better for me.
Check out this video I made:
http://www.youtube.com/watch?v=b1xYF...e-nzQ&index=20
Bob
#450
Join Date: Jun 2012
Location: JOSHUA,
TX
Posts: 181
Likes: 0
Received 0 Likes
on
0 Posts
RE: Fleet Brotherhood
If you go to your arts & craft store. go to the bead section. where they sell the glitter stuff, here you will fine automatic rivets in different sizes. I had used them on a lot of war birds. since I can't send photos on this computor. they look like this. o-o-o-o-o- . you will get about 200 on a roll. 2 rolls per pkge. about $ 1.99 . you can cut the rivets inbetween. Or keep them attached. sray your primer coat. and your paint color. never know the diference. And saves time. Company name Darice inc. www.darice.com . I hope this helps some. HANK #20