Go Back  RCU Forums > RC Helicopters > Electric RC Helis > Helimax
Reload this Page >

Factory Pitch/Throttle curves Axe Cp

Notices
Helimax This is for all your Helimax questions and comments.

Factory Pitch/Throttle curves Axe Cp

Old 11-29-2009, 12:48 PM
  #1  
garyji
Member
Thread Starter
 
Join Date: Nov 2009
Location: Rutherfordton, NC
Posts: 30
Likes: 0
Received 0 Likes on 0 Posts
Default Factory Pitch/Throttle curves Axe Cp



Anyone know how to find the original pitch and throttle curves programed into the AXE cp with all original equipment??

Thanks, G.

Old 12-17-2009, 04:25 PM
  #2  
Shadow99
Senior Member
 
Join Date: Aug 2007
Location: Southwick, MA
Posts: 511
Likes: 0
Received 0 Likes on 0 Posts
Default RE: Factory Pitch/Throttle curves Axe Cp

These are the measured values I had before I changed to a DX7 TX.

Throttle curves:
Normal: 0.0%, 36.0%, 72.0%, 83.5%, 100%
Idle Up: 100.0%, 83.5%, 72.0%, 83.5%, 100%

Pitch curves:
Normal: 40.0%, 45.0%, 50.0%, 72.5%, 100.0%
Idle Up: 0.0%, 27.5%, 50.0%, 72.5%, 100.0%

However, there is no way of changing them using the old version 1 TX, on the V3 TX there was some slight adjustments you could do using the external pots on the TX.

Shadow
Old 12-17-2009, 04:47 PM
  #3  
garyji
Member
Thread Starter
 
Join Date: Nov 2009
Location: Rutherfordton, NC
Posts: 30
Likes: 0
Received 0 Likes on 0 Posts
Default RE: Factory Pitch/Throttle curves Axe Cp

Thanks so much. Shadow. I have some servo amp connectors coming from HK and am using a DX6i for the conversion. These will be the settings I plug in at first to get a start point.

Thanks,

G.
Old 12-18-2009, 08:21 AM
  #4  
Shadow99
Senior Member
 
Join Date: Aug 2007
Location: Southwick, MA
Posts: 511
Likes: 0
Received 0 Likes on 0 Posts
Default RE: Factory Pitch/Throttle curves Axe Cp

Hey Gary, Here are some more details of the programming I did using the DX7.

Model name: MX300
Model 1: Heli DSM
Swash Type: 3 servos 120'
Input Select: AUX2-INH GEAR-gear
THRO Recovery-INH
TRAINER-INH

I added the programming mix so that any cyclic/pitch change gives you 20% increase in throttle, this keeps the headspeed up and the response lag down (if you do not have Bell-Hiller Mixing an the head). With BH mixing it will respond like a hummingbird on JOLT soda!

Prog Mix 1: ELEV-THRO Rate:+20% -20% SW:ON Offset:0
Prog Mix 2: AILE-THRO Rate:+20% -20% SW:ON Offset:0
Prog Mix 3: PIT-THRO Rate:+20% 0% SW:ON Offset:0

Revo Mix: ALL ZEROS (unused)
Throttle curves:
Normal: 0.0%, 36.0%, 72.0%, 83.5%, 100%
ST1: 100.0%, 83.5%, 72.0%, 83.5%, 100%
ST2: 100.0% (across the board!)

Pitch curves:
Normal: 40.0%, 45.0%, 50.0%, 72.5%, 100.0%
ST1: 0.0%, 27.5%, 50.0%, 72.5%, 100.0%
ST2: (same as ST1)

Thro HOLD: Hold Pos 0% SW:AUX 2 (Only use after rotor has stopped, will strip main gear with BL motor in flight)

Swash Mix: 3-servos 120' EXP-INH
AILE -100%
ELEV -100%
PIT -60%

Travel Adjust: ALL 100%
Sub-Trim: Adjust as nessasary with your servos & linkages (try and keep values low or 0 on RUD if using Belt Driven Tail & servo)

Reverse Switches #4 & #6 (All others are NORMAL 1,2,3,5,7)

AUTO D/R EXP NORM-INH
ST-1 P0
ST-2 P1
HOLD INH
D/R & EXP Position 0 (RUD,ELEV,AILE) d/r 50%
Position 1 (RUD,ELEV,AILE) d/r 100%


Shadow

Old 12-18-2009, 12:38 PM
  #5  
PilotLight
Senior Member
My Feedback: (1)
 
PilotLight's Avatar
 
Join Date: Aug 2003
Location: Benton Harbor, MI
Posts: 1,027
Likes: 0
Received 0 Likes on 0 Posts
Default RE: Factory Pitch/Throttle curves Axe Cp


ORIGINAL: Shadow99


Thro HOLD: Hold Pos 0% SW:AUX 2 (Only use after rotor has stopped, will strip main gear with BL motor in flight)

Shadow, is your brake enabled on your brushless ESC?

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.