Optima RX and HV servos
#1
Thread Starter
My Feedback: (125)
Optima RX and HV servos
I'm going to venture into the HV realm on my next plane and will start off using the 5495BH servos, 2S Lipo and an Optima series receiver, either a 6 or 7.
What is the best way to wire this for a glow powered plane?
A) 7.4V directly to the BAT/servo port
B) 7.4V -> regulator to X voltage - > BAT port
C) Pull SPC jumper and go 7.4V ->Y -> SPC & BAT
D)or?
Thanks in advance!
What is the best way to wire this for a glow powered plane?
A) 7.4V directly to the BAT/servo port
B) 7.4V -> regulator to X voltage - > BAT port
C) Pull SPC jumper and go 7.4V ->Y -> SPC & BAT
D)or?
Thanks in advance!
#2
Senior Member
RE: Optima RX and HV servos
[quote ]ORIGINAL: Hemikiller I'm going to venture into the HV realm on my next plane and will start off using the 5495BH servos, 2S Lipo and an Optima series receiver, either a 6 or 7.
What is the best way to wire this for a glow powered plane?
A) 7.4V directly to the BAT/servo port
B) 7.4V -> regulator to X voltage - > BAT port
C) Pull SPC jumper and go 7.4V ->Y -> SPC & BAT
D)or? Thanks in advance! [/quote]
answered:
Optima Transceiver (RX) - Battery set up for Nitro/Gas models
following may also assist:
Optima Transceiver (RX) - Battery set up for Nitro/Gas models - caution re NiMH & Alert re LiFE.
Optima Transceiver (RX) - Dual or Multiple Batteries may be installed - Avoid Brownout & Add Redundancy, even one for each servo.
Alan T.
What is the best way to wire this for a glow powered plane?
A) 7.4V directly to the BAT/servo port
B) 7.4V -> regulator to X voltage - > BAT port
C) Pull SPC jumper and go 7.4V ->Y -> SPC & BAT
D)or? Thanks in advance! [/quote]
answered:
Optima Transceiver (RX) - Battery set up for Nitro/Gas models
following may also assist:
Optima Transceiver (RX) - Battery set up for Nitro/Gas models - caution re NiMH & Alert re LiFE.
Optima Transceiver (RX) - Dual or Multiple Batteries may be installed - Avoid Brownout & Add Redundancy, even one for each servo.
Alan T.
#3
Member
Join Date: Mar 2011
Location: Brooklyn Park,
MN
Posts: 77
Likes: 0
Received 0 Likes
on
0 Posts
RE: Optima RX and HV servos
ORIGINAL: Hemikiller
I'm going to venture into the HV realm on my next plane and will start off using the 5495BH servos, 2S Lipo and an Optima series receiver, either a 6 or 7.
What is the best way to wire this for a glow powered plane?
A) 7.4V directly to the BAT/servo port
B) 7.4V -> regulator to X voltage - > BAT port
C) Pull SPC jumper and go 7.4V ->Y -> SPC & BAT
D)or?
Thanks in advance!
I'm going to venture into the HV realm on my next plane and will start off using the 5495BH servos, 2S Lipo and an Optima series receiver, either a 6 or 7.
What is the best way to wire this for a glow powered plane?
A) 7.4V directly to the BAT/servo port
B) 7.4V -> regulator to X voltage - > BAT port
C) Pull SPC jumper and go 7.4V ->Y -> SPC & BAT
D)or?
Thanks in advance!