Midwest Super Stearman Instructions
#1
Thread Starter
My Feedback: (5)
Join Date: Nov 2010
Location: Marseilles, IL
Posts: 72
Likes: 0
Received 0 Likes
on
0 Posts
Midwest Super Stearman Instructions
I am looking for a copy of the instruction book for the Midwest Super Stearman, as I can't find mine anywhere. Does anyone have a copy they can scan and send to me, possibly in pdf form?Thanks in advance...
#2
Senior Member
Join Date: Nov 2002
Location: Round Rock,
TX
Posts: 417
Likes: 0
Received 0 Likes
on
0 Posts
RE: Midwest Super Stearman Instructions
Was Midwest not helpful? Even though they don't make RC kits anymore, I would think they could help. [link=http://www.midwestproducts.com/contact.asp]Link[/link]
#4
Banned
RE: Midwest Super Stearman Instructions
ORIGINAL: DaleJEckart
Last time I asked, I think they wanted 30-40 bucks or so for the instructions.
Last time I asked, I think they wanted 30-40 bucks or so for the instructions.
It cost them money to print extra copies.
Zor
#5
Join Date: Jun 2007
Location: Grand Blanc,
MI
Posts: 536
Likes: 0
Received 0 Likes
on
0 Posts
RE: Midwest Super Stearman Instructions
I am currently building the Midwest Stearman. I can scan the book for you, but it may take me a little time. As I recall, it is about 90 pages.
#6
Thread Starter
My Feedback: (5)
Join Date: Nov 2010
Location: Marseilles, IL
Posts: 72
Likes: 0
Received 0 Likes
on
0 Posts
RE: Midwest Super Stearman Instructions
Thanks, I'd appreciate it. Take your time, I'm not starting it yet E-mail to: [email protected] Thanks Again!
#7
Join Date: Jun 2007
Location: Grand Blanc,
MI
Posts: 536
Likes: 0
Received 0 Likes
on
0 Posts
RE: Midwest Super Stearman Instructions
I just sent the manual, It was not as long as I had recalled, it's about 60 pages, but it turned out to be a rather large file. Let me know if you have any trouble receiving it or opening it. I hope you enjoy the build, if you look for the check marks in the manual, you can get an idea of where I am at with mine.
I just got a note back that the e-mail did not goes through due to the size of the attachment. I will see if I can make a more manageable version. I have a newer scanner that I haven't worked with much, so I may need to change some settings.
I just got a note back that the e-mail did not goes through due to the size of the attachment. I will see if I can make a more manageable version. I have a newer scanner that I haven't worked with much, so I may need to change some settings.
#9
Thread Starter
My Feedback: (5)
Join Date: Nov 2010
Location: Marseilles, IL
Posts: 72
Likes: 0
Received 0 Likes
on
0 Posts
RE: Midwest Super Stearman Instructions
I downloaded the first one, looks great!Will get them all when I get home to my desktop. I owe you one, bigtime! Let me know if there's anything you need. Thanks again! Dale
#11
Junior Member
My Feedback: (3)
Join Date: Mar 2004
Location: Ontario,
OR
Posts: 6
Likes: 0
Received 0 Likes
on
0 Posts
RE: Midwest Super Stearman Instructions
I believe I still have the manual. If you still need it let me know and I will send it PDF file to your email. Might take me a couple of days to find it.
#15
Banned
Hi guys,
If no specific info is posted then _ _ _
Set the CG between 25% and 30% of the chord at the wings root as measured from the leading edges line at its mid point.
Set the control surfaces rotation a max of 40 degrees of rotation and use proportional as you control.
Zor
If no specific info is posted then _ _ _
Set the CG between 25% and 30% of the chord at the wings root as measured from the leading edges line at its mid point.
Set the control surfaces rotation a max of 40 degrees of rotation and use proportional as you control.
Zor
Last edited by Zor; 11-18-2014 at 05:32 PM.
#16
Join Date: Jun 2007
Location: Grand Blanc,
MI
Posts: 536
Likes: 0
Received 0 Likes
on
0 Posts
The plans show the CG approx 4.9 inches aft of the upper wing leading edge. The recommended throws are: Ailerons 1/2" up and down on low rates and 5/8" on high rates, Elevator 3/4" up and 11/32" down for low rates and 1" up and 7/16" down for high. Rudder is recommended at 1 1/4" right and Left. If you would like the manual, PM me with your e-mail and I can send it to you.
#18
Hi my name is Alex Guzman and I just got one Midwest Super Stearman kit, the kit looks like is complete except for the instructions, I tried many sites and I can't find it, could you please tell me if you have and I can get a copy or PDF file?.
PS: I also got 3 Stearman kits if you need one, please let me know.
Thanks in advance
Alex
PS: I also got 3 Stearman kits if you need one, please let me know.
Thanks in advance
Alex