Astula--Frank's reply is what the Sig plans call for. If you are entering in a scale contest, you will probably need to make something more scale. It's been a while, but there used to be a guy named Cubman that had a web site with lots of photos of the full scale cub. He is probably referenced and even posted on this thread. I doubt if what the Sig plans call for would be considered scale. If I am wrong, surely others will comment.
Good luck. |
1 Attachment(s)
Originally Posted by FlyingGreg
(Post 12187714)
Astula--Frank's reply is what the Sig plans call for. If you are entering in a scale contest, you will probably need to make something more scale. It's been a while, but there used to be a guy named Cubman that had a web site with lots of photos of the full scale cub. He is probably referenced and even posted on this thread. I doubt if what the Sig plans call for would be considered scale. If I am wrong, surely others will comment.
Good luck. Here a photo video of my first scale model J-3 Cub 1/4 SIG . The model is the PH-GEN Nederlands http://www.rcuniverse.com/forum/atta...mentid=2151812 https://youtu.be/36Ag65rAerk @+ Astula |
Hi, has som body a bleuprint Clipped Wing "WINGS" :confused:
@+ Astula |
Cubman's site. I purchased his L-4 plans a while back and they are really nice. Haven't built it yet but they look similar in design to the Sig with some scale mods.
http://www.thecubden.org |
2 Attachment(s)
I have been thanking of building another piper and was doing research again on the cub when I came across this forums. its been awhile sense someone had a post or build. are there anyone out there still enjoy building and flying or has Foamies, ARF, and drones taken over.
Anyway I am thanking of building another cub like the first one I had be for the crash and the salvage rebuild into a L-4 it a Sig 1/4 scale and still have it. if I can get he pic's to load the white one is the first build and the black/white is the second. http://www.rcuniverse.com/forum/atta...mentid=2207135http://www.rcuniverse.com/forum/atta...mentid=2207136 |
Originally Posted by fcf
(Post 12320283)
I have been thanking of building another piper and was doing research again on the cub when I came across this forums. its been awhile sense someone had a post or build. are there anyone out there still enjoy building and flying or has Foamies, ARF, and drones taken over.
.......... Still Building but Drones are a distraction :D I still havent flown my 1/4 Cub yet but managed to acquire a 40size fixer upper which I just completed for an every day fun flier. Good luck with your build Cubs are fun builds and have tones of scale potential. oops sorry got to go just got distracted by the lingerie Model popups on the page...doh! |
Originally Posted by WacoNut
(Post 10767584)
Eric,
You can see how I covered my Cub on page 5 of this thread. What covering material are you using? I used Sig Koerall and it works great. I started by covering the stab before attaching to the fuse. The fuse was covered with 5 pcs. I started by covering the bottom of the fuse overlapping to the side of the bottom stringer. The fuse sides were covered next. I attached the covering to the bottom stringer to the top side stringer overlapping on those as well. The top was covered with 2 pcs. You are also going to cover the fin with the top of the fuse. Cut a pice of covering large enough to cover the fin and one half of the fuse top(top center stringer to fuse side top stringer). Apply the covering to the fuse top 1st then to the fin. The filet can be tricky but is easier to do with cloth covering versus iron on plastic. As you are covering the fin keep pulling the fabric tight to remove the wrinkles as you go. Once shrunk you should have a nice smooth fillet. Hope this helps!! Anthony |
I have used latex on two 1/4 scales and sprayed both.
|
Thanks. I use an automotive touch up gun. Would that work without thinning the paint?
|
|
Thanks, this is exactly what I was looking for. I do have another question. I was looking over airplane requirements and they state servos with ratings greater than 35 in/lb (HD) should be used. I realize this manual was written some time ago and standard digital servos are rated much higher. I have a few Spektrum A6180’s (82/94 in/lb 4.8v-6.0v) and a few Hi-Tec HS-5625MG (109/130 in/lb 4.8-6.0v) all new. Are these considered powerful enough for this airplane? If not what should be the minimum spec servo? Also I noticed the aileron servos are going to require a fairly long servo extension. Should I be conserved about voltage loss out to the servo? I use a JR9303 2.4Mhz system. Thanks for answering all my questions. This is my 6th kit build and my first 1/4 scale build. 1st Cub build. Just want to get it right. I’m just going to build it to the Sig plan. Not much bashing.
|
1/4 scale intrament panel
Does anyone have a source for "drop in" scale panel for the Sig J3 besides the high dollar I-Tallies?
|
Originally Posted by cmy6
(Post 12389059)
Thanks, this is exactly what I was looking for. I do have another question. I was looking over airplane requirements and they state servos with ratings greater than 35 in/lb (HD) should be used. I realize this manual was written some time ago and standard digital servos are rated much higher. I have a few Spektrum A6180’s (82/94 in/lb 4.8v-6.0v) and a few Hi-Tec HS-5625MG (109/130 in/lb 4.8-6.0v) all new. Are these considered powerful enough for this airplane? If not what should be the minimum spec servo? Also I noticed the aileron servos are going to require a fairly long servo extension. Should I be conserved about voltage loss out to the servo? I use a JR9303 2.4Mhz system. Thanks for answering all my questions. This is my 6th kit build and my first 1/4 scale build. 1st Cub build. Just want to get it right. I’m just going to build it to the Sig plan. Not much bashing.
Gerry |
Originally Posted by d boothe
(Post 12402649)
Does anyone have a source for "drop in" scale panel for the Sig J3 besides the high dollar I-Tallies?
fit on the scroll saw and touch it up with a little paint works for me. |
Originally Posted by cubcrasher
(Post 12402870)
I use the one for the Hangar 9 cub. Trim it to
fit on the scroll saw and touch it up with a little paint works for me. Thanks D |
All times are GMT -8. The time now is 07:27 AM. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.