Go Back  RCU Forums > RC Airplanes > Pylon Universe - RC Pylon Racing > Q-40 Racing
Reload this Page >

Build a Miss Ashley - Revisited

Notices
Q-40 Racing Discuss AMA 422 and any other variants of Quarter 40 racing

Build a Miss Ashley - Revisited

Old 01-19-2018, 05:49 PM
  #76  
sahartman21
Thread Starter
 
Join Date: Nov 2007
Location: Fritch, TX
Posts: 2,060
Likes: 0
Received 0 Likes on 0 Posts
Default Build a Miss Ashley - Revisited

I test fit the horizontal tail surface and checked the incidence.

At level (0 degree incidence) on the meter the string level should also show level.

I checked the prop clearance to the ground.

Target about 1/2" of clearance when the wing is level and the prop hangs down. I prefer short gear as this reduces the likelihood of bouncing on landing.
Attached Thumbnails Click image for larger version

Name:	IMG_9509.JPG
Views:	88
Size:	81.2 KB
ID:	2251604   Click image for larger version

Name:	IMG_9510.JPG
Views:	84
Size:	78.6 KB
ID:	2251605   Click image for larger version

Name:	IMG_9511.JPG
Views:	86
Size:	89.8 KB
ID:	2251606   Click image for larger version

Name:	IMG_9512.JPG
Views:	105
Size:	98.2 KB
ID:	2251607  

Last edited by sahartman21; 02-26-2018 at 07:15 PM.
Old 01-20-2018, 07:32 AM
  #77  
sahartman21
Thread Starter
 
Join Date: Nov 2007
Location: Fritch, TX
Posts: 2,060
Likes: 0
Received 0 Likes on 0 Posts
Default Build a Miss Ashley - Revisited

During the Ashley MM build thread the fuselage nose cone was identified as having some down thrust. This is also seen with the pictures here.

The nose cone measured about 2 to 2 1/2 degrees of down thrust compared to the wing.

I reduced the down thrust by shaping the nose cone with a Dremel tool. I marked a 1/32" cut on the top of the nose cone and used the tools to reduce the down thrust. It now has a small amount of down thrust, possibly 1 degree.

This process took about 15 minutes to accomplish and was not difficult to address.
Attached Thumbnails Click image for larger version

Name:	IMG_9513.JPG
Views:	92
Size:	79.5 KB
ID:	2251663   Click image for larger version

Name:	IMG_9514.JPG
Views:	99
Size:	77.1 KB
ID:	2251664   Click image for larger version

Name:	IMG_9515.JPG
Views:	92
Size:	76.7 KB
ID:	2251665   Click image for larger version

Name:	IMG_9516.JPG
Views:	98
Size:	80.2 KB
ID:	2251666   Click image for larger version

Name:	IMG_9518.JPG
Views:	89
Size:	87.6 KB
ID:	2251667   Click image for larger version

Name:	IMG_9519.JPG
Views:	92
Size:	82.3 KB
ID:	2251668   Click image for larger version

Name:	IMG_9520.JPG
Views:	153
Size:	83.3 KB
ID:	2251669  

Last edited by sahartman21; 01-20-2018 at 07:47 AM.
Old 01-20-2018, 10:12 AM
  #78  
sahartman21
Thread Starter
 
Join Date: Nov 2007
Location: Fritch, TX
Posts: 2,060
Likes: 0
Received 0 Likes on 0 Posts
Default Build a Miss Ashley - Revisited

The following pictures shows the initial fitting and attaching the belly pan to the wing. Shoe Goo was used to attach the belly pan as it is shock resistant. Some epoxies may also work OK in this service.

This method produces a permanently installed belly pan that does not use race tape.
Attached Thumbnails Click image for larger version

Name:	IMG_9521.JPG
Views:	94
Size:	85.4 KB
ID:	2251678   Click image for larger version

Name:	IMG_9522.JPG
Views:	88
Size:	78.1 KB
ID:	2251679   Click image for larger version

Name:	IMG_9523.JPG
Views:	82
Size:	84.7 KB
ID:	2251680   Click image for larger version

Name:	IMG_9524.JPG
Views:	85
Size:	86.6 KB
ID:	2251681   Click image for larger version

Name:	IMG_9527.JPG
Views:	78
Size:	101.6 KB
ID:	2251682   Click image for larger version

Name:	IMG_9528.JPG
Views:	84
Size:	84.0 KB
ID:	2251683   Click image for larger version

Name:	IMG_9529.JPG
Views:	76
Size:	75.1 KB
ID:	2251684  

Last edited by sahartman21; 04-02-2018 at 05:54 PM.
Old 01-20-2018, 10:16 AM
  #79  
sahartman21
Thread Starter
 
Join Date: Nov 2007
Location: Fritch, TX
Posts: 2,060
Likes: 0
Received 0 Likes on 0 Posts
Default Build a Miss Ashley - Revisited

Some body filler is used to flare the fuselage into the wing.

A razor saw is used to cut the wing away from the fuselage.
Attached Thumbnails Click image for larger version

Name:	IMG_9530.JPG
Views:	74
Size:	82.5 KB
ID:	2251687   Click image for larger version

Name:	IMG_9531.JPG
Views:	83
Size:	95.3 KB
ID:	2251688   Click image for larger version

Name:	IMG_9532.JPG
Views:	79
Size:	105.1 KB
ID:	2251689   Click image for larger version

Name:	IMG_9533.JPG
Views:	75
Size:	87.5 KB
ID:	2251690   Click image for larger version

Name:	IMG_9535.JPG
Views:	72
Size:	99.6 KB
ID:	2251691   Click image for larger version

Name:	IMG_9536.JPG
Views:	71
Size:	69.3 KB
ID:	2251692   Click image for larger version

Name:	IMG_9538.JPG
Views:	67
Size:	86.5 KB
ID:	2251693   Click image for larger version

Name:	IMG_9539.JPG
Views:	78
Size:	77.6 KB
ID:	2251694  

Old 01-20-2018, 10:22 AM
  #80  
sahartman21
Thread Starter
 
Join Date: Nov 2007
Location: Fritch, TX
Posts: 2,060
Likes: 0
Received 0 Likes on 0 Posts
Default Build a Miss Ashley - Revisited

Waxed paper was taped on the fuselage to keep the parts from sticking together.

A piece of balsa was fitted and was glued to the back of the belly pan.

This assembly was taped in place to insure that parts fit later.
Attached Thumbnails Click image for larger version

Name:	IMG_9540.JPG
Views:	79
Size:	77.9 KB
ID:	2251697   Click image for larger version

Name:	IMG_9541.JPG
Views:	72
Size:	75.4 KB
ID:	2251698   Click image for larger version

Name:	IMG_9542.JPG
Views:	73
Size:	81.6 KB
ID:	2251699   Click image for larger version

Name:	IMG_9543.JPG
Views:	71
Size:	76.6 KB
ID:	2251700   Click image for larger version

Name:	IMG_9544.JPG
Views:	71
Size:	71.1 KB
ID:	2251701   Click image for larger version

Name:	IMG_9545.JPG
Views:	69
Size:	80.6 KB
ID:	2251702   Click image for larger version

Name:	IMG_9546.JPG
Views:	90
Size:	79.0 KB
ID:	2251703  

Last edited by sahartman21; 01-20-2018 at 10:26 AM.
Old 01-20-2018, 04:59 PM
  #81  
sahartman21
Thread Starter
 
Join Date: Nov 2007
Location: Fritch, TX
Posts: 2,060
Likes: 0
Received 0 Likes on 0 Posts
Default Build a Miss Ashley - Revisited

Slots were cut for the installation of the elevator horn.

This installation uses a 1 1/4" long horn to lower the throw to about 1/8" each way.

Make sure there is room for the horn and pushrod before gluing parts in place.
Attached Thumbnails Click image for larger version

Name:	IMG_9547.JPG
Views:	88
Size:	83.6 KB
ID:	2251740   Click image for larger version

Name:	IMG_9549.JPG
Views:	94
Size:	84.1 KB
ID:	2251741   Click image for larger version

Name:	IMG_9551.JPG
Views:	91
Size:	69.2 KB
ID:	2251742   Click image for larger version

Name:	IMG_9553.JPG
Views:	83
Size:	70.6 KB
ID:	2251743   Click image for larger version

Name:	IMG_9554.JPG
Views:	84
Size:	82.9 KB
ID:	2251744   Click image for larger version

Name:	IMG_9555.JPG
Views:	86
Size:	79.9 KB
ID:	2251745   Click image for larger version

Name:	IMG_9556.JPG
Views:	95
Size:	73.9 KB
ID:	2251746   Elevator Horn.pdf  


Last edited by sahartman21; 03-01-2018 at 08:13 AM. Reason: Added template for Elevator Horn and Tail Skid
Old 01-20-2018, 05:03 PM
  #82  
sahartman21
Thread Starter
 
Join Date: Nov 2007
Location: Fritch, TX
Posts: 2,060
Likes: 0
Received 0 Likes on 0 Posts
Default Build a Miss Ashley - Revisited

A stick of balsa was glued in place at the hinge line.

This should be wide enough for the installation of numerous hinges. I try to install 5 hinges in the rudder service.
Attached Thumbnails Click image for larger version

Name:	IMG_9557.JPG
Views:	93
Size:	82.3 KB
ID:	2251747  
Old 01-20-2018, 05:06 PM
  #83  
sahartman21
Thread Starter
 
Join Date: Nov 2007
Location: Fritch, TX
Posts: 2,060
Likes: 0
Received 0 Likes on 0 Posts
Default Build a Miss Ashley - Revisited

Here are a few pictures showing the belly pan and wing fillet.

The Miss Ashley will make another nice looking model.
Attached Thumbnails Click image for larger version

Name:	IMG_9558.JPG
Views:	100
Size:	85.7 KB
ID:	2251748   Click image for larger version

Name:	IMG_9559.JPG
Views:	103
Size:	83.5 KB
ID:	2251749   Click image for larger version

Name:	IMG_9560.JPG
Views:	96
Size:	88.9 KB
ID:	2251750  
Old 01-26-2018, 06:52 PM
  #84  
sahartman21
Thread Starter
 
Join Date: Nov 2007
Location: Fritch, TX
Posts: 2,060
Likes: 0
Received 0 Likes on 0 Posts
Default Build a Miss Ashley - Revisited

The alignment was verified with an incidence meter and a string level.

I followed by tacking the tail in place with some medium CA.

A mix of finishing epoxy, cabosel, and cotton flocks was made to make the final joint with the fuselage.

My finger was used to smooth out the mix and make a small fillet.

I then set the model out of the way to dry.
Attached Thumbnails Click image for larger version

Name:	IMG_9566.JPG
Views:	82
Size:	87.0 KB
ID:	2252333   Click image for larger version

Name:	IMG_9567.JPG
Views:	79
Size:	71.6 KB
ID:	2252334   Click image for larger version

Name:	IMG_9568.JPG
Views:	80
Size:	79.8 KB
ID:	2252335   Click image for larger version

Name:	IMG_9569.JPG
Views:	79
Size:	80.2 KB
ID:	2252336   Click image for larger version

Name:	IMG_9578.JPG
Views:	75
Size:	112.0 KB
ID:	2252337   Click image for larger version

Name:	IMG_9572.JPG
Views:	76
Size:	84.0 KB
ID:	2252338   Click image for larger version

Name:	IMG_9573.JPG
Views:	68
Size:	73.7 KB
ID:	2252339   Click image for larger version

Name:	IMG_9574.JPG
Views:	69
Size:	84.9 KB
ID:	2252340  

Click image for larger version

Name:	IMG_9575.JPG
Views:	82
Size:	71.6 KB
ID:	2252341   Click image for larger version

Name:	IMG_9577.JPG
Views:	84
Size:	100.9 KB
ID:	2252342  

Last edited by sahartman21; 01-27-2018 at 05:18 AM.
Old 01-27-2018, 06:24 PM
  #85  
sahartman21
Thread Starter
 
Join Date: Nov 2007
Location: Fritch, TX
Posts: 2,060
Likes: 0
Received 0 Likes on 0 Posts
Default Build a Miss Ashley - Revisited

Pieces of balsa were inserted in the grove to keep the mix out of the gap while gluing.

I used a mix of finishing epoxy and micro balloons to fill the area.

The model was set out of the way to dry overnight.
Attached Thumbnails Click image for larger version

Name:	IMG_9595.JPG
Views:	79
Size:	64.8 KB
ID:	2252408   Click image for larger version

Name:	IMG_9596.JPG
Views:	69
Size:	113.7 KB
ID:	2252409   Click image for larger version

Name:	IMG_9597.JPG
Views:	65
Size:	91.5 KB
ID:	2252410   Click image for larger version

Name:	IMG_9598.JPG
Views:	68
Size:	85.9 KB
ID:	2252411  
Old 01-28-2018, 06:05 PM
  #86  
sahartman21
Thread Starter
 
Join Date: Nov 2007
Location: Fritch, TX
Posts: 2,060
Likes: 0
Received 0 Likes on 0 Posts
Default Build a Miss Ashley - Revisited

A scrapper blade was used to scrape the surface flat.
Attached Thumbnails Click image for larger version

Name:	IMG_9599.JPG
Views:	66
Size:	63.3 KB
ID:	2252592   Click image for larger version

Name:	IMG_9600.JPG
Views:	77
Size:	80.8 KB
ID:	2252593   Click image for larger version

Name:	IMG_9601.JPG
Views:	75
Size:	68.4 KB
ID:	2252594  
Old 01-28-2018, 06:08 PM
  #87  
sahartman21
Thread Starter
 
Join Date: Nov 2007
Location: Fritch, TX
Posts: 2,060
Likes: 0
Received 0 Likes on 0 Posts
Default Build a Miss Ashley - Revisited

I copied an earlier model to approximate the hole for the engine.

The firewall is located about 3 3/4" back from the spinner cone.
Attached Thumbnails Click image for larger version

Name:	IMG_9579.JPG
Views:	78
Size:	120.3 KB
ID:	2252595   Click image for larger version

Name:	IMG_9580.JPG
Views:	76
Size:	107.4 KB
ID:	2252596   Click image for larger version

Name:	IMG_9582.JPG
Views:	71
Size:	99.2 KB
ID:	2252597   Click image for larger version

Name:	IMG_9584.JPG
Views:	74
Size:	98.2 KB
ID:	2252598  
Old 01-28-2018, 06:12 PM
  #88  
sahartman21
Thread Starter
 
Join Date: Nov 2007
Location: Fritch, TX
Posts: 2,060
Likes: 0
Received 0 Likes on 0 Posts
Default Build a Miss Ashley - Revisited

The firewall was cut out of 3/8" thick aircraft plywood.

Below is the template that I used.
Attached Thumbnails Ashley Firewalls.pdf   Click image for larger version

Name:	IMG_9585.JPG
Views:	63
Size:	54.8 KB
ID:	2252608   Click image for larger version

Name:	IMG_9587.JPG
Views:	66
Size:	76.0 KB
ID:	2252609   Click image for larger version

Name:	IMG_9589.JPG
Views:	66
Size:	93.6 KB
ID:	2252610  
Old 01-28-2018, 06:16 PM
  #89  
sahartman21
Thread Starter
 
Join Date: Nov 2007
Location: Fritch, TX
Posts: 2,060
Likes: 0
Received 0 Likes on 0 Posts
Default Build a Miss Ashley - Revisited

Below are some pictures showing the installation of the engine and mount:
Attached Thumbnails Click image for larger version

Name:	IMG_9602.JPG
Views:	81
Size:	91.8 KB
ID:	2252615   Click image for larger version

Name:	IMG_9603.JPG
Views:	73
Size:	87.8 KB
ID:	2252616   Click image for larger version

Name:	IMG_9604.JPG
Views:	77
Size:	87.9 KB
ID:	2252617   Click image for larger version

Name:	IMG_9605.JPG
Views:	72
Size:	87.3 KB
ID:	2252618   Click image for larger version

Name:	IMG_9608.JPG
Views:	75
Size:	118.9 KB
ID:	2252619   Click image for larger version

Name:	IMG_9609.JPG
Views:	85
Size:	141.7 KB
ID:	2252620   Click image for larger version

Name:	IMG_9610.JPG
Views:	86
Size:	84.3 KB
ID:	2252621  
Old 01-28-2018, 06:23 PM
  #90  
sahartman21
Thread Starter
 
Join Date: Nov 2007
Location: Fritch, TX
Posts: 2,060
Likes: 0
Received 0 Likes on 0 Posts
Default Build a Miss Ashley - Revisited

The firewall and motor mount were tacked in place with a couple drops of CA.

A long 1/8" diameter bit was used to drill the holes for the motor mount screws.

I make my engine kill from a piece of 9/32" diameter tubing. A hole was drilled for the installation of the tubing. I ended up moving the engine kill to the left hand side (instead of right as shown) of the needle valve.
Attached Thumbnails Click image for larger version

Name:	IMG_9612.JPG
Views:	86
Size:	111.9 KB
ID:	2252633   Click image for larger version

Name:	IMG_9613.JPG
Views:	70
Size:	108.0 KB
ID:	2252634   Click image for larger version

Name:	IMG_9614.JPG
Views:	76
Size:	89.0 KB
ID:	2252635   Click image for larger version

Name:	IMG_9615.JPG
Views:	80
Size:	96.9 KB
ID:	2252636   Click image for larger version

Name:	IMG_9616.JPG
Views:	74
Size:	69.8 KB
ID:	2252637   Click image for larger version

Name:	IMG_9617.JPG
Views:	74
Size:	72.2 KB
ID:	2252638   Click image for larger version

Name:	IMG_9618.JPG
Views:	78
Size:	87.6 KB
ID:	2252639   Click image for larger version

Name:	IMG_9619.JPG
Views:	73
Size:	88.0 KB
ID:	2252640  


Last edited by sahartman21; 03-13-2018 at 03:06 PM.
Old 01-28-2018, 06:34 PM
  #91  
sahartman21
Thread Starter
 
Join Date: Nov 2007
Location: Fritch, TX
Posts: 2,060
Likes: 0
Received 0 Likes on 0 Posts
Default Build a Miss Ashley - Revisited

Holes for the tubing were drilled at this time. The holes were located about 1 1/2" back from the engine kill and were 1/4" diameter.
Attached Thumbnails Click image for larger version

Name:	IMG_9620.JPG
Views:	72
Size:	87.4 KB
ID:	2252645   Click image for larger version

Name:	IMG_9621.JPG
Views:	71
Size:	87.3 KB
ID:	2252646  

Last edited by sahartman21; 01-28-2018 at 07:00 PM.
Old 01-28-2018, 06:39 PM
  #92  
sahartman21
Thread Starter
 
Join Date: Nov 2007
Location: Fritch, TX
Posts: 2,060
Likes: 0
Received 0 Likes on 0 Posts
Default Build a Miss Ashley - Revisited

The mount was removed and the firewall was knocked loose.

The holes were enlarged to 3/16" and the blind nuts were installed.

Medium CA was used to glue the blind nuts and kill tube in place.
Attached Thumbnails Click image for larger version

Name:	IMG_9622.JPG
Views:	71
Size:	75.0 KB
ID:	2252647   Click image for larger version

Name:	IMG_9623.JPG
Views:	76
Size:	88.6 KB
ID:	2252648   Click image for larger version

Name:	IMG_9624.JPG
Views:	76
Size:	64.3 KB
ID:	2252649   Click image for larger version

Name:	IMG_9625.JPG
Views:	68
Size:	69.6 KB
ID:	2252650   Click image for larger version

Name:	IMG_9626.JPG
Views:	66
Size:	79.3 KB
ID:	2252651   Click image for larger version

Name:	IMG_9628.JPG
Views:	73
Size:	88.6 KB
ID:	2252652   Click image for larger version

Name:	IMG_9629.JPG
Views:	65
Size:	91.4 KB
ID:	2252653   Click image for larger version

Name:	IMG_9630.JPG
Views:	75
Size:	78.5 KB
ID:	2252654  

Old 01-28-2018, 06:43 PM
  #93  
sahartman21
Thread Starter
 
Join Date: Nov 2007
Location: Fritch, TX
Posts: 2,060
Likes: 0
Received 0 Likes on 0 Posts
Default Build a Miss Ashley - Revisited

This engine kill tube was filled and the motor mount was covered with petroleum jelly to reduce the possibility of being stuck with glue.
Attached Thumbnails Click image for larger version

Name:	IMG_9631.JPG
Views:	68
Size:	76.9 KB
ID:	2252655   Click image for larger version

Name:	IMG_9632.JPG
Views:	78
Size:	95.2 KB
ID:	2252656  

Last edited by sahartman21; 03-21-2018 at 04:48 PM.
Old 01-28-2018, 06:48 PM
  #94  
sahartman21
Thread Starter
 
Join Date: Nov 2007
Location: Fritch, TX
Posts: 2,060
Likes: 0
Received 0 Likes on 0 Posts
Default Build a Miss Ashley - Revisited

Some finishing epoxy was mixed and was applied to the surface of the firewall.

Cotton flock was added to the remaining epoxy. It was spread around the outside of the firewall to hold it in place.

The tuned muffler is located on the centerline of the model. It makes a clean installation.
Attached Thumbnails Click image for larger version

Name:	IMG_9634.JPG
Views:	64
Size:	109.5 KB
ID:	2252657   Click image for larger version

Name:	IMG_9635.JPG
Views:	64
Size:	93.8 KB
ID:	2252658   Click image for larger version

Name:	IMG_9636.JPG
Views:	70
Size:	99.2 KB
ID:	2252659   Click image for larger version

Name:	IMG_9637.JPG
Views:	71
Size:	85.8 KB
ID:	2252660   Click image for larger version

Name:	IMG_9638.JPG
Views:	71
Size:	129.3 KB
ID:	2252661   Click image for larger version

Name:	IMG_9639.JPG
Views:	73
Size:	78.6 KB
ID:	2252662   Click image for larger version

Name:	IMG_9640.JPG
Views:	74
Size:	75.7 KB
ID:	2252663   Click image for larger version

Name:	IMG_9641.JPG
Views:	74
Size:	82.5 KB
ID:	2252664  

Old 01-31-2018, 09:24 AM
  #95  
sahartman21
Thread Starter
 
Join Date: Nov 2007
Location: Fritch, TX
Posts: 2,060
Likes: 0
Received 0 Likes on 0 Posts
Default Build a Miss Ashley - Revisited

A cutout template is now available as a PDF document.

To use it:
  1. Print it out full size.
  2. Cut the template flush on the seam line.
  3. Wrap the template around the nose area and tape the template seam onto the bottom fuselage seam.
  4. Initially cut the hole for the engine a little small and enlarge the hole as needed.
Attached Thumbnails Click image for larger version

Name:	IMG_9643.JPG
Views:	61
Size:	98.9 KB
ID:	2252917   2018-01-31 Engine Cutout.pdf  

Last edited by sahartman21; 01-31-2018 at 09:30 AM.
Old 01-31-2018, 03:10 PM
  #96  
sahartman21
Thread Starter
 
Join Date: Nov 2007
Location: Fritch, TX
Posts: 2,060
Likes: 0
Received 0 Likes on 0 Posts
Default Build a Miss Ashley - Revisited

The ailerons are made from a cut into the foam core wing. This exposes the foam core to any future paint that is applied to the wing.

Some finishing epoxy was mixed and applied to the foam surfaces. The excess epoxy was wiped off and the wing was set out of the way to dry.
Attached Thumbnails Click image for larger version

Name:	IMG_9644.JPG
Views:	70
Size:	89.9 KB
ID:	2252976   Click image for larger version

Name:	IMG_9645.JPG
Views:	64
Size:	98.8 KB
ID:	2252977   Click image for larger version

Name:	IMG_9646.JPG
Views:	63
Size:	87.4 KB
ID:	2252978  
Old 01-31-2018, 03:15 PM
  #97  
sahartman21
Thread Starter
 
Join Date: Nov 2007
Location: Fritch, TX
Posts: 2,060
Likes: 0
Received 0 Likes on 0 Posts
Default Build a Miss Ashley - Revisited

The front of the engine mount should be mounted down to reduce the possibility of vibration.

Some 6-32 screws were installed and a mix of 6-minute epoxy and fiberglass cloth was applied on the screws.
Attached Thumbnails Click image for larger version

Name:	IMG_9647.JPG
Views:	76
Size:	89.7 KB
ID:	2252979   Click image for larger version

Name:	IMG_9648.JPG
Views:	68
Size:	76.6 KB
ID:	2252980   Click image for larger version

Name:	IMG_9649.JPG
Views:	60
Size:	80.6 KB
ID:	2252981   Click image for larger version

Name:	IMG_9650.JPG
Views:	64
Size:	106.3 KB
ID:	2252982   Click image for larger version

Name:	IMG_9651.JPG
Views:	60
Size:	82.2 KB
ID:	2252983   Click image for larger version

Name:	IMG_9652.JPG
Views:	80
Size:	75.1 KB
ID:	2252984  
Old 02-03-2018, 03:46 PM
  #98  
sahartman21
Thread Starter
 
Join Date: Nov 2007
Location: Fritch, TX
Posts: 2,060
Likes: 0
Received 0 Likes on 0 Posts
Default Build a Miss Ashley - Revisited

Here are a few pictures of the rudder hinge installation.

Five CA hinges were used.
Attached Thumbnails Click image for larger version

Name:	IMG_9689.JPG
Views:	66
Size:	66.8 KB
ID:	2253318   Click image for larger version

Name:	IMG_9690.JPG
Views:	69
Size:	79.7 KB
ID:	2253319   Click image for larger version

Name:	IMG_9691.JPG
Views:	68
Size:	73.4 KB
ID:	2253320   Click image for larger version

Name:	IMG_9693.JPG
Views:	71
Size:	72.9 KB
ID:	2253321  
Old 02-03-2018, 03:50 PM
  #99  
sahartman21
Thread Starter
 
Join Date: Nov 2007
Location: Fritch, TX
Posts: 2,060
Likes: 0
Received 0 Likes on 0 Posts
Default Build a Miss Ashley - Revisited

Here are some pictures showing the radio installation:
Attached Thumbnails Click image for larger version

Name:	IMG_9679.JPG
Views:	77
Size:	98.5 KB
ID:	2253322   Click image for larger version

Name:	IMG_9680.JPG
Views:	65
Size:	82.8 KB
ID:	2253323   Click image for larger version

Name:	IMG_9682.JPG
Views:	59
Size:	67.6 KB
ID:	2253324   Click image for larger version

Name:	IMG_9686.JPG
Views:	70
Size:	83.5 KB
ID:	2253325   Click image for larger version

Name:	IMG_9687.JPG
Views:	65
Size:	82.3 KB
ID:	2253326   Click image for larger version

Name:	IMG_9692.JPG
Views:	79
Size:	105.4 KB
ID:	2253327   Click image for larger version

Name:	IMG_9693.JPG
Views:	74
Size:	72.9 KB
ID:	2253328   Click image for larger version

Name:	IMG_9694.JPG
Views:	69
Size:	61.9 KB
ID:	2253329  

Click image for larger version

Name:	IMG_9695.JPG
Views:	72
Size:	86.4 KB
ID:	2253330  
Old 02-03-2018, 07:00 PM
  #100  
sahartman21
Thread Starter
 
Join Date: Nov 2007
Location: Fritch, TX
Posts: 2,060
Likes: 0
Received 0 Likes on 0 Posts
Default Build a Miss Ashley - Revisited

These pictures show the aileron servo installation.
Attached Thumbnails Click image for larger version

Name:	IMG_9696.JPG
Views:	73
Size:	89.7 KB
ID:	2253361   Click image for larger version

Name:	IMG_9697.JPG
Views:	75
Size:	85.3 KB
ID:	2253362  

Thread Tools
Search this Thread

Contact Us - Manage Preferences - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.