How to make flaps deploy slowly on JR 9303?
#1
Senior Member
Thread Starter
My Feedback: (2)
Join Date: Aug 2003
Location: Blythewood,
SC
Posts: 1,256
Likes: 0
Received 0 Likes
on
0 Posts
How to make flaps deploy slowly on JR 9303?
Greetings,
Can you all advise me on what settings I need to make the flaps deployed slowly? On my 9393, there are three flaps positions and what can I do to make them move smoothly? Thanks DP
Can you all advise me on what settings I need to make the flaps deployed slowly? On my 9393, there are three flaps positions and what can I do to make them move smoothly? Thanks DP
#2
My Feedback: (20)
RE: How to make flaps deploy slowly on JR 9303?
I have a JR 8103 but am not familiar with the 9303. Unless it has provisions as in some high end radios to slow the servos you can add one of these: http://www.emsjomar.com/SearchResult.aspx?CategoryID=6
I have one and it works fine.
Chuck
I have one and it works fine.
Chuck
#3
Senior Member
Join Date: Aug 2002
Location: Jonkoping, SWEDEN
Posts: 1,301
Likes: 0
Received 0 Likes
on
0 Posts
RE: How to make flaps deploy slowly on JR 9303?
IMHO the 9303 is a high end radio. It has a very nice servo speed adjust function where each servo can have a separate speed in each direction that is Flight Mode or switch selectable.
To adjust servo speed, simply highlight and select SRV. Speed in the FUNCTION List.
The servo speed can be adjusted from 0.176 seconds/60 degrees (very fast if the servo is normally this fast or faster) up to a maximum value of 15 seconds /60 degrees of travel (very slow).
To adjust servo speed, simply highlight and select SRV. Speed in the FUNCTION List.
The servo speed can be adjusted from 0.176 seconds/60 degrees (very fast if the servo is normally this fast or faster) up to a maximum value of 15 seconds /60 degrees of travel (very slow).
#4
My Feedback: (1)
RE: How to make flaps deploy slowly on JR 9303?
The 9303 has a flap delay build into the Flap System.
Go to DEVICE SELECT on the System Menu
On the bottom row, under FLAP, Press the Selector until SYS. shows.
Go to the FUNCTION MENU.
Select FLAP SYSTEM (You must have SYS selected on DEVICE SELECT under FLAP or the Flap System Menu won't show)
In the lower right corner is Delay
Scroll to it
Press the Selector
Roll Selector to any amount from INH to 2.0 seconds in 0.1 sec intervals.
Go to DEVICE SELECT on the System Menu
On the bottom row, under FLAP, Press the Selector until SYS. shows.
Go to the FUNCTION MENU.
Select FLAP SYSTEM (You must have SYS selected on DEVICE SELECT under FLAP or the Flap System Menu won't show)
In the lower right corner is Delay
Scroll to it
Press the Selector
Roll Selector to any amount from INH to 2.0 seconds in 0.1 sec intervals.
#5
Senior Member
Thread Starter
My Feedback: (2)
Join Date: Aug 2003
Location: Blythewood,
SC
Posts: 1,256
Likes: 0
Received 0 Likes
on
0 Posts
RE: How to make flaps deploy slowly on JR 9303?
Hello all
Thank you for your replies. On my Stuka what would be the appropriate speed for flap deployment? I see so many planes pitch up suddenly so slow deployment would help don't you think? DP
Thank you for your replies. On my Stuka what would be the appropriate speed for flap deployment? I see so many planes pitch up suddenly so slow deployment would help don't you think? DP
#6
Banned
Join Date: Jan 2010
Location: Lacona, NY
Posts: 1,840
Likes: 0
Received 0 Likes
on
0 Posts
RE: How to make flaps deploy slowly on JR 9303?
I have a Hobby Lobby Servo Retarder that delays one of my E-flite Electric Retract, so it looks a little more realistic. (Like a Luftwaffe Aircraft) But on my 72mhz 6 channel I don't have a speed function like some of those high end radios seem to have. I wish they had something out for he standard mechanical retract servo, that would be wild.
Pete
Pete