RE: What do you think of FORMOST 150 ?
Hello Nicolas,
Do you have any photos of your complete setup? Can't wait for your flight reports Rich |
RE: What do you think of FORMOST 150 ?
1 Attachment(s)
Here are the long awaited photos of the turbine conversion.... I am VERY VERY happy with the outcome !
The fuselage is now rock solid with the new bulkheads in much better plywood and better construction, everything fits like a glove as well... The original short wing spars are replaced with a CF 16 mm OD tube (in front) and a CF 10mm OD rod (in rear) as well. Great combination. Hopefully we have good weather this weekend ! :D |
RE: What do you think of FORMOST 150 ?
1 Attachment(s)
...more...
Gas tank, electronic retract valve and nose wheel steering servo are under the removable tray. The tray is held with four M3 hex bolts. Next to the Futaba FASST receiver with short aerials is the RX battery monitor (VoltSpy MC from Graupner). Fuel tank is 2000 ml (approx 68 oz) - Digitech UAT is 125 ml (approx 4 oz) ; this should be good for about 10 minutes flights with the SimJet 1200. The main fuel tank is held in place by the neck by means of a 10mm wide velcro strap which runs through the foreseen openings in the bulkheads. Totally hassle free to take it out ! |
RE: What do you think of FORMOST 150 ?
1 Attachment(s)
...more...
Both full length wing spars clearly visible under the turbine... |
RE: What do you think of FORMOST 150 ?
1 Attachment(s)
...more...
(SimJet 1200 AES installed) |
RE: What do you think of FORMOST 150 ?
1 Attachment(s)
...more...
Perfect fit of the Jet 1A trailing link struts plus the retracts, operated with a double Digitech electronic valve. - PS : no problem in combination with my Futaba FASST receiver - You can see the main wing tube passing through the wheel bay. |
RE: What do you think of FORMOST 150 ?
1 Attachment(s)
...more...
Rudder and aileron linkage with MK accessories. On ailerons (flaperons !) + elevator : Futaba BLS451 On rudders : Futaba S3305 (only ones I had - not my choice of preference... -) |
RE: What do you think of FORMOST 150 ?
1 Attachment(s)
Graupner Voltspy.
RX battery pack is a 5 cells 1700 MAh Sanyo SCR NiCad, installed in the nose accessible through the nose hatch. The ECU battery is a 3S-2150 MAh Lipo, on top of the fuel tank with velcro straps. |
RE: What do you think of FORMOST 150 ?
Enjoy !
Tomorrow evening I will finish the canopy ther****rm mould and make some of these newly shaped canopies... Nicolas. |
RE: What do you think of FORMOST 150 ?
Sandor,
Your set of bulkheads to test is under its way ! Nicolas. |
RE: What do you think of FORMOST 150 ?
Too kewl
Any plans to market or submit a PDf version of the upgrades ? Happy flight and many more to come. Great job !! |
RE: What do you think of FORMOST 150 ?
Yes !
For all enquiries, drawings, bulkheads and/or parts, please contact Mr. Sandor Kruise at Digitech Turbines : http://www.digitech-turbines.com/ Thanks ! Nicolas. |
RE: What do you think of FORMOST 150 ?
ORIGINAL: bahamadude Too kewl Any plans to market or submit a PDf version of the upgrades ? Happy flight and many morew to come. Great job !! yes we are infact all the drawings will be in Coreldraw - Autocad - and as a PDF file thanks to Spiderjet for himn doing a lot of work all measurements are taken from our parts Airtanks - Fueltank i will try to make it today will upload them asap. so lets all make a fine turbine jet out of a 249 usd trainer. make us proud!. show us the Build and flight reports BTW: ready made turbine conversions will be also up for sale. these will include Fuel tank incl all hardware Fueltank is 2000ml / 68 ounces is made of very thick PE and will outperform any Sulivan or Kevlar tank. output will be a festo to 6mm to direct connection to a UAT all Formers CNC cut by Spiderjets and more stuff i can think of. i am looking for wingtubes BUT to ship them in 1 meter of length to the USA is a nightmare. so best is if someone would sort the tubings out maybe the chinese will pick this up and make a ready to sell Turbine trainer like Formost 190 TC ..;) |
RE: What do you think of FORMOST 150 ?
there are a few items uploaded to our webshop.
fuel tanks are on stock Bearers are almost made as we speak. also the drawings are ready for download 17 MB zip file it contains all DXF-DWG-PDF-CDR files also has all pictures as a sample however to download you need to be a MEMBER to download these files it is in the Formost section,look under jets. it is FORBIDDEN to link the files outside our webshop. it is also forbidden to distribute any file seperatly from these zip files. it is forbidden to sell formers without permission from the owner. if you are interested to machine and sell formers or fuel tanks for the Formost upgrade kit this is possible please email us for details.. http://shop.digitech-turbines.com |
RE: What do you think of FORMOST 150 ?
Nicolas / Sandor,
Quick Question, I have always seen CF spars run through some sort of sleeve tube. Has this been done just to provide a guide or does it add strength to the spar as it provides radial containment? Is the spar going to be removable or is it fixed? Thanks from FL Jets Rich |
RE: What do you think of FORMOST 150 ?
|
RE: What do you think of FORMOST 150 ?
ORIGINAL: RCISFUN Nicolas / Sandor, Quick Question, I have always seen CF spars run through some sort of sleeve tube. Has this been done just to provide a guide or does it add strength to the spar as it provides radial containment? Is the spar going to be removable or is it fixed? Thanks from FL Jets Rich No other real function than guiding the wing tubes (which are removable). Just jealous not to be at FL Jets with all of you.... perhaps next time !!! :D Nicolas. |
RE: What do you think of FORMOST 150 ?
Nicolas if you come I'll buy the Beer:D:D:D:D:D
|
RE: What do you think of FORMOST 150 ?
ORIGINAL: RCISFUN Nicolas if you come I'll buy the Beer:D:D:D:D:D Thanks for the offer but I must be the only Belgian who doesn't like beer at all ! [:@] Offer me some kerosene next time, 'cause that's what I can't bring along ! Nicolas. |
RE: What do you think of FORMOST 150 ?
Rich, Looks like rain, ice and snow for the next three weeks Sooooo I'll trade you some Jet-A for the beer!!!!
|
RE: What do you think of FORMOST 150 ?
Looking at the PDF file on page 2 what should it be blown up to get the actual size ?
|
RE: What do you think of FORMOST 150 ?
ORIGINAL: bahamadude Looking at the PDF file on page 2 what should it be blown up to get the actual size ? Good tip : take the wood set from Digitech. For about the price of a Sullivan tank you get the wood artwork as well (and the round tank !). The wood parts are CNC milled with a 1.2mm diameter router bit with a precision of 0.02 mm accuracy. The CAD drawings were made for those who wish to mill with a router bit up to 1.8mm. Use high quality birch plywood thickness 3.4mm and 5 mm respectively. For the price that Sandor is only asking for it it isn't worth it spending hours on trying to match it more or less by hand, plus making a donation to the Make-A-Wish Foundation... (see his website) [8D] Just my realistic 2 cents... Nicolas. |
RE: What do you think of FORMOST 150 ?
Hint
Tip;) Conversion fees will make it too high unfortunately. We dont do euro here. |
RE: What do you think of FORMOST 150 ?
Today we are at 1,52 exchange rate dollar vs euro already.... Incredible !
|
RE: What do you think of FORMOST 150 ?
I notice the wood parts and fuel tank on the Digi Tech site are for the Formost 160 and 190. What is the diference between these aircraft and will the parts fit in the 150.
Thanks |
All times are GMT -8. The time now is 07:35 AM. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.