Notices
RC Radios, Transmitters, Receivers, Servos, gyros Discussion all about rc radios, transmitters, receivers, servos, etc.

Help with futuba t9chp radio w dft module

Old 03-14-2021, 08:01 AM
  #1  
BRETTMAN
Thread Starter
My Feedback: (11)
 
Join Date: Feb 2002
Location: S. DAYTONA FL. NJ
Posts: 71
Likes: 0
Received 0 Likes on 0 Posts
Default Help with futuba t9chp radio w dft module

Hi everyone,i have a futuba t9chp same almost to 9c radio..recvr. Is pluged in alirons and pitch for left and right turns,both on 140 percent butturns left twice as far as right..is there a fix for this??? Thanx brett
Old 03-14-2021, 09:04 AM
  #2  
BarracudaHockey
My Feedback: (11)
 
BarracudaHockey's Avatar
 
Join Date: Jul 2003
Location: Jacksonville, FL
Posts: 24,741
Received 95 Likes on 80 Posts
Default

Been a while, but i think you have to move the stick each way to set the travel direction
Old 03-14-2021, 08:27 PM
  #3  
BRETTMAN
Thread Starter
My Feedback: (11)
 
Join Date: Feb 2002
Location: S. DAYTONA FL. NJ
Posts: 71
Likes: 0
Received 0 Likes on 0 Posts
Default

BARRACUDA JOCKY that sounds more like gyro install,thanx anyway BRETT
Old 03-15-2021, 08:48 AM
  #4  
daveopam
My Feedback: (9)
 
daveopam's Avatar
 
Join Date: Oct 2002
Location: ELK CITY, OK
Posts: 7,693
Received 21 Likes on 20 Posts
Default

I'm sorry but I'm not sure I understand your question. I use a 10C now but used a 9C for many years. Can you clarify any?

David
Old 03-18-2021, 07:52 PM
  #5  
BRETTMAN
Thread Starter
My Feedback: (11)
 
Join Date: Feb 2002
Location: S. DAYTONA FL. NJ
Posts: 71
Likes: 0
Received 0 Likes on 0 Posts
Default

your right barracuda,I did move stick both ways,just the one plugged in ail. to 140 percent than i went to pitch which is other side of ail. put that also to 140 percent..But still turns more left than right..So question is can i do anything to turn equally????
Old 03-19-2021, 12:36 AM
  #6  
DGrant
My Feedback: (4)
 
DGrant's Avatar
 
Join Date: Dec 2001
Location: Clovis, CA
Posts: 2,172
Received 27 Likes on 26 Posts
Default

It sounds like you've got a mix activated. Do you have any other models in the radio to compare too, or even an open memory slot that's still set to factory default you could plug things into for testing? Just to compare at this point is all. If your functions are equal when set to default, and you go to your model slot and they're off, then again it would likely be a mix that's activated. Just a few thoughts there.

I'm a long time 9C user myself, although it's been quite a while since I've fiddled with mixes, I do remember a few things.. haha... and I still use my 9C a few times a year as well. They're great radios and mine's worked flawlessly for many years. I hope you get yours worked out.
Old 03-19-2021, 05:37 AM
  #7  
BRETTMAN
Thread Starter
My Feedback: (11)
 
Join Date: Feb 2002
Location: S. DAYTONA FL. NJ
Posts: 71
Likes: 0
Received 0 Likes on 0 Posts
Default

Thanks d-grant,i'll check mixes thanks brett
Old 03-19-2021, 09:33 AM
  #8  
BRETTMAN
Thread Starter
My Feedback: (11)
 
Join Date: Feb 2002
Location: S. DAYTONA FL. NJ
Posts: 71
Likes: 0
Received 0 Likes on 0 Posts
Default

Hi,i checked all mixes all inh...still more left than right ail i checked servo in basic menu,and it shows left is twiice as far in left than right,i'm baffled,,.i'm gonna try putting y-harness on pitch to ail. See what happen's any other idea's will be appreciated thanx brett
Old 03-23-2021, 10:41 AM
  #9  
daveopam
My Feedback: (9)
 
daveopam's Avatar
 
Join Date: Oct 2002
Location: ELK CITY, OK
Posts: 7,693
Received 21 Likes on 20 Posts
Default

Did you zero out the sub trim?

David
Old 03-23-2021, 11:00 AM
  #10  
BRETTMAN
Thread Starter
My Feedback: (11)
 
Join Date: Feb 2002
Location: S. DAYTONA FL. NJ
Posts: 71
Likes: 0
Received 0 Likes on 0 Posts
Default

HI,Yes all trims,sub trims are on zero,I Even e-mailed futuba-usa,no answer yet,, thanks BRETT

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.