Meet the 2MPH race team
#1
Thread Starter
My Feedback: (4)
Join Date: Sep 2003
Location: Temecula, CA
Posts: 5,692
Likes: 0
Received 0 Likes
on
0 Posts
Meet the 2MPH race team
Here is my crawling team all ready for some upcoming competitions. The Losi MRC and AX-10. Here is the pair of them:
The AX-10 has:
Losi crawler body and tires, 1/8 Giga Crusher shocks w/Maxx springs, high clearance end links, 2/3A saddle pack, Hitec MG-645 servo, Hot Racing dig w/Futaba servo, 14t pinion, Integy crawler motor, Novak Rooster Crawler, weighted wheels (6oz front/4 oz back) and quite a few more goodies.
The Losi MRC has:
Custom chassis, ESC on back plate, Futaba MG up front, aluminum crawler shocks, 2/3 pack mounted on front axle/upper plate, weighted wheels, true beadlock losi wheels w/2" PVC and Losi tires, 13T pinion. It needs high clearance links, I really need to order those.
The AX-10 has:
Losi crawler body and tires, 1/8 Giga Crusher shocks w/Maxx springs, high clearance end links, 2/3A saddle pack, Hitec MG-645 servo, Hot Racing dig w/Futaba servo, 14t pinion, Integy crawler motor, Novak Rooster Crawler, weighted wheels (6oz front/4 oz back) and quite a few more goodies.
The Losi MRC has:
Custom chassis, ESC on back plate, Futaba MG up front, aluminum crawler shocks, 2/3 pack mounted on front axle/upper plate, weighted wheels, true beadlock losi wheels w/2" PVC and Losi tires, 13T pinion. It needs high clearance links, I really need to order those.
#5
Thread Starter
My Feedback: (4)
Join Date: Sep 2003
Location: Temecula, CA
Posts: 5,692
Likes: 0
Received 0 Likes
on
0 Posts
RE: Meet the 2MPH race team
Oh, sure. I pulled the upper radio plate, cut the shock upper mount sections off and bolted them to HPI Savage cross members. This allowed me to move the receiver down and get the ESC down on the back axle. As an added bonus, I can adjust the truck's height by rotating the crossmembers.
#10
Senior Member
Join Date: Feb 2008
Location: Charlottesville, VA
Posts: 1,996
Likes: 0
Received 0 Likes
on
0 Posts
RE: Meet the 2MPH race team
Awe nice touch with the batteries on the axles. I think I'll do that with mine. I just don't see a good way to mount a battery on the lower chassis plate without it being in the way. Gonna mean running a few extra wires but the lower CoG will be worth it.
Nice lookin rigs.
Nice lookin rigs.
#12
Senior Member
Join Date: Nov 2006
Location: Buford,
GA
Posts: 339
Likes: 0
Received 0 Likes
on
0 Posts
RE: Meet the 2MPH race team
Are the 2/3 A cells giving good run time?
I was planning on Seven sub-C cells for my Killer Krawler, maybe I should plan on 2/3A's instead ???
I am planning because I have ordered a crawler, but haven't recieved all needed parts quite yet....
Harry
I was planning on Seven sub-C cells for my Killer Krawler, maybe I should plan on 2/3A's instead ???
I am planning because I have ordered a crawler, but haven't recieved all needed parts quite yet....
Harry
#13
Thread Starter
My Feedback: (4)
Join Date: Sep 2003
Location: Temecula, CA
Posts: 5,692
Likes: 0
Received 0 Likes
on
0 Posts
RE: Meet the 2MPH race team
The 2/3A cells give me a good 15-20 minutes of crawl time with the Axial and 30 minutes with the Losi MRC. Those high turn motors last quite a while. The cells get warm to the touch with the Axial after a full run. When I run one pack through the Axial, and then run one pack through the MRC, plus setup times it takes me one to one and a half hours which is right for a crawling session for me.
#14
Senior Member
Join Date: Nov 2006
Location: Buford,
GA
Posts: 339
Likes: 0
Received 0 Likes
on
0 Posts
RE: Meet the 2MPH race team
Integy crawler motor with 13T pinion, but what wind motor?
maybe this one?
http://www3.towerhobbies.com/cgi-bin...?&I=LXTRC4&P=7
are you at 6 cells, because did you know you can go 7 cells with that ESC?
Harry
maybe this one?
http://www3.towerhobbies.com/cgi-bin...?&I=LXTRC4&P=7
are you at 6 cells, because did you know you can go 7 cells with that ESC?
Harry
#15
Thread Starter
My Feedback: (4)
Join Date: Sep 2003
Location: Temecula, CA
Posts: 5,692
Likes: 0
Received 0 Likes
on
0 Posts
RE: Meet the 2MPH race team
I have only run 55T motors- the integy 55T and the Novak Fifty-Five. Honestly, 6 cells gets the Axial competitive. I am competitive with all of the other machines I run with and I can even do some things others can't. If I felt that I needed 8.4V, I would definitely do it, I just don't feel like I do.
Integy 55T-
[link]http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXKUG5&P=7[/link]
Novak Fifty Five
[link=http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXTJD7&P=7]http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXTJD7&P=7[/link]
Integy 55T-
[link]http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXKUG5&P=7[/link]
Novak Fifty Five
[link=http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXTJD7&P=7]http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXTJD7&P=7[/link]