Your TRUGGY and your setup
04-16-2010, 01:58 PM
#51
Member
Join Date: Mar 2010
Location: Marwayne, AB, CANADA
Posts: 55
Likes: 0
Received 0 Likes
on
0 Posts
RE: Your TRUGGY and your setup
TRUGGY : Xray XT8
THR SERVO : Hitec 7966HB
STR SERVO : Hitec 7955TG
MOTOR : O.S. .21 VZ-B V-Spec Limited Edition
PIPE : O.S. T-2060WN
RADIO : Futaba 3PM-X
CLUTCH : Ofna Blue w/black springs
CB : Stock 13 (for now)
WHEELS : Panther Gator on zero-offset Losi dish
DIFFS F/C/R : 5/7/10
SHOCKS F/R : 40/40
DROOP F/R : full (+ added bit from chassis mod)
RIDE HEIGHT : arms level
CAMBER F/R : -2/-2
05-04-2010, 01:49 PM
#52
Member
Join Date: Apr 2010
Location: West Brom, UNITED KINGDOM
Posts: 61
Likes: 0
Received 0 Likes
on
0 Posts
RE: Your TRUGGY and your setup
My new truggy Kit
I use the same stuff in my buggy
TRUGGY :Hong nor X1CRT
THR SERVO :Hitec HS 5645
STR SERVO :Ace DS1015
MOTOR :RB WS7 III
PIPE : STS 0403
RADIO : DX3S
CLUTCH :Fioroni 35MM
CB :15T
WHEELS :Proline Crime fighters
DIFFS F/C/R :Standard
RIDE HEIGHT :32 47
CAMBER F/R :-1 -2
I use the same stuff in my buggy
TRUGGY :Hong nor X1CRT
THR SERVO :Hitec HS 5645
STR SERVO :Ace DS1015
MOTOR :RB WS7 III
PIPE : STS 0403
RADIO : DX3S
CLUTCH :Fioroni 35MM
CB :15T
WHEELS :Proline Crime fighters
DIFFS F/C/R :Standard
RIDE HEIGHT :32 47
CAMBER F/R :-1 -2
05-17-2010, 02:07 AM
#53
Senior Member
Join Date: Dec 2009
Location: statham, GA
Posts: 930
Likes: 0
Received 0 Likes
on
0 Posts
RE: Your TRUGGY and your setup
New Truggy:
TRUGGY : Hotbodies D8T
THR SERVO : Hitec 7955
STR SERVO : Hitec 7954
MOTOR : Alpha
PIPE : Alpha 0801
RADIO : Airtronics m11
CLUTCH : Odonnell
CB : 13 T (hotbodies)
WHEELS : AKA
DIFFS F/C/R : 7/10/3
SHOCKS F/R : 500/400
SPRINGS F/R: Blue/white
ADDED STUFF: aluminum servo horn for steering, and putting on WCE drive shafts and Kyosho front center drive shaft.
TRUGGY : Hotbodies D8T
THR SERVO : Hitec 7955
STR SERVO : Hitec 7954
MOTOR : Alpha
PIPE : Alpha 0801
RADIO : Airtronics m11
CLUTCH : Odonnell
CB : 13 T (hotbodies)
WHEELS : AKA
DIFFS F/C/R : 7/10/3
SHOCKS F/R : 500/400
SPRINGS F/R: Blue/white
ADDED STUFF: aluminum servo horn for steering, and putting on WCE drive shafts and Kyosho front center drive shaft.
07-25-2010, 01:28 PM
#55
Senior Member
My Feedback: (23)
Join Date: Jan 2008
Location: Colorado Springs,
CO
Posts: 315
Likes: 0
Received 0 Likes
on
0 Posts
RE: Your TRUGGY and your setup
My Truggy So far ( I hope to upgrade servos)
Truggy: Losi 8ight-t 1.0
Engine: O.S. .28xz
Clutch: Losi Four shoe aluminum
Clutch Bell: Losi 13T
Spur Gear: 50T
Pipe: O.S. 2060
Steering Servo: Some 244oz one
Throttle Servo: Ofna SX100
Diffs: Stock, Not sure
Shocks: Stock, Not sure
Rx pack: Losi 1100mah nimh
Reciever: Some three channel fm I got from a buddy
Tires: Pro-line Bowtie LPR
Wheels: JConcepts Rulux dyed blue
Other Goodies: King Headz Wheel extenders to accept zero offset wheels, Aluminum Chassis Braces, 2.0 radio box.
Like I said I hope to upgrade my throttle servo and get a good radio. So far so Fun!!!!!
Truggy: Losi 8ight-t 1.0
Engine: O.S. .28xz
Clutch: Losi Four shoe aluminum
Clutch Bell: Losi 13T
Spur Gear: 50T
Pipe: O.S. 2060
Steering Servo: Some 244oz one
Throttle Servo: Ofna SX100
Diffs: Stock, Not sure
Shocks: Stock, Not sure
Rx pack: Losi 1100mah nimh
Reciever: Some three channel fm I got from a buddy
Tires: Pro-line Bowtie LPR
Wheels: JConcepts Rulux dyed blue
Other Goodies: King Headz Wheel extenders to accept zero offset wheels, Aluminum Chassis Braces, 2.0 radio box.
Like I said I hope to upgrade my throttle servo and get a good radio. So far so Fun!!!!!
07-27-2010, 04:37 PM
#56
Senior Member
Join Date: Oct 2006
Location: Sonoma,
CA
Posts: 1,289
Likes: 0
Received 0 Likes
on
0 Posts
RE: Your TRUGGY and your setup
ORIGINAL: ProRCRacer88
all around use for now
TRUGGY : Kyosho ST-RR
THR SERVO : JR DZ8550 ( 188 oz torque )
STR SERVO : JR 9100S
MOTOR : RB 928 TM
PIPE : RB 2045
RADIO : Nomadio Sensor
CLUTCH :Werks4 shoe(Stock ofna clutch temporary)
CB : 14T vented
WHEELS : Proline LPRs and LPR bowtiesand crimefighters
DIFFS F/C/R : 7,000 15,000 2,000
SHOCKS F/R :kyosho 600wt front / kyosho 700wt rear
DROOP F/R : n/a
RIDE HEIGHT : n/a
CAMBER F/R : n/a
all around use for now
TRUGGY : Kyosho ST-RR
THR SERVO : JR DZ8550 ( 188 oz torque )
STR SERVO : JR 9100S
MOTOR : RB 928 TM
PIPE : RB 2045
RADIO : Nomadio Sensor
CLUTCH :Werks4 shoe(Stock ofna clutch temporary)
CB : 14T vented
WHEELS : Proline LPRs and LPR bowtiesand crimefighters
DIFFS F/C/R : 7,000 15,000 2,000
SHOCKS F/R :kyosho 600wt front / kyosho 700wt rear
DROOP F/R : n/a
RIDE HEIGHT : n/a
CAMBER F/R : n/a
Torque: 150 oz/in @ 4.8V, 180 oz/in @ 6V
You need a jr9100T
07-28-2010, 09:36 AM
#57
Senior Member
Join Date: Nov 2006
Location: Lafayette,
LA
Posts: 417
Likes: 0
Received 0 Likes
on
0 Posts
RE: Your TRUGGY and your setup
TRUGGY : Losi 8T 2.0
RADIO :Spektrum DXR
STR SERVO :HiTech 7955
THR SERVO :HiTech 7985
MOTOR : OS Pro Mod
PIPE: OS 2050 or OS 2060
CB : 13/50 All lightened drive train
Clutch : Al w/gold springs
WHEELS/TIRES : Anything Soft City Block, Calibers
DIFFS F/C/R :7/10/2
SHOCKS F/R :35/32.5
DROOP F/R : 107/130
RIDE HEIGHT F/R : 29/42
CAMBER F/R : -2.0/-2.0
Here are a few pics form my last race.
Hard landing I must say.
This is an oooooo moment.
New wheelie king?
RADIO :Spektrum DXR
STR SERVO :HiTech 7955
THR SERVO :HiTech 7985
MOTOR : OS Pro Mod
PIPE: OS 2050 or OS 2060
CB : 13/50 All lightened drive train
Clutch : Al w/gold springs
WHEELS/TIRES : Anything Soft City Block, Calibers
DIFFS F/C/R :7/10/2
SHOCKS F/R :35/32.5
DROOP F/R : 107/130
RIDE HEIGHT F/R : 29/42
CAMBER F/R : -2.0/-2.0
Here are a few pics form my last race.
Hard landing I must say.
This is an oooooo moment.
New wheelie king?
07-31-2010, 07:01 AM
#58
Junior Member
Join Date: Jul 2010
Location: Bristol,
VA
Posts: 26
Likes: 0
Received 0 Likes
on
0 Posts
RE: Your TRUGGY and your setup
TRUGGY : Caster K8TPro Kit
THR SERVO : Hitec HS-7950TH
STR SERVO : Hitec HS-7950TH
MOTOR : Werks B5
PIPE :OS 2060
RADIO : FUTABA 3 PKs
CLUTCH : STOCK, but with Mugen 1.1 springs
CB :Yes, I have 1 in my REALtruck !LOL!!! (couldnt help it!) 13T
WHEELS :J Concepts half ups
DIFFS F/C/R : 10K/7K/1K
SHOCKS F/R :35 fr/45 Rr
DROOP F/R :I aint tellin!
RIDE HEIGHT :dont remember. HAVE to look!
CAMBER F/R :-1/-1 & -1 on toe OUT!
THR SERVO : Hitec HS-7950TH
STR SERVO : Hitec HS-7950TH
MOTOR : Werks B5
PIPE :OS 2060
RADIO : FUTABA 3 PKs
CLUTCH : STOCK, but with Mugen 1.1 springs
CB :Yes, I have 1 in my REALtruck !LOL!!! (couldnt help it!) 13T
WHEELS :J Concepts half ups
DIFFS F/C/R : 10K/7K/1K
SHOCKS F/R :35 fr/45 Rr
DROOP F/R :I aint tellin!
RIDE HEIGHT :dont remember. HAVE to look!
CAMBER F/R :-1/-1 & -1 on toe OUT!
10-08-2010, 09:55 PM
#59
Senior Member
Thread Starter
Join Date: Feb 2008
Location: Tulsa,
OK
Posts: 344
Likes: 0
Received 0 Likes
on
0 Posts
RE: Your TRUGGY and your setup
update on my truggy and setup...
TRUGGY : xt8
THR SERVO : Hitec 7945
STR SERVO : Hitec 7940
MOTOR : Werks B5
PIPE : 2013
RADIO : m11
CLUTCH : JVD
CB : 15
WHEELS : IBeams
DIFFS F/C/R : 7k/10k/2k
SHOCKS F/R : 30/35
DROOP F/R : parallel to ground
RIDE HEIGHT : 30/36
CAMBER F/R : -2/-4
TRUGGY : xt8
THR SERVO : Hitec 7945
STR SERVO : Hitec 7940
MOTOR : Werks B5
PIPE : 2013
RADIO : m11
CLUTCH : JVD
CB : 15
WHEELS : IBeams
DIFFS F/C/R : 7k/10k/2k
SHOCKS F/R : 30/35
DROOP F/R : parallel to ground
RIDE HEIGHT : 30/36
CAMBER F/R : -2/-4
10-08-2010, 10:40 PM
#60
Senior Member
Join Date: Dec 2009
Location: statham, GA
Posts: 930
Likes: 0
Received 0 Likes
on
0 Posts
RE: Your TRUGGY and your setup
New Truggy:
TRUGGY : O'donnell Z01-T
THR SERVO : Savox 1256TG
STR SERVO : Hitec 7955
MOTOR : Alpha S852 (Orange Head)
PIPE : Alpha 0801
RADIO : Airtronics m11
CLUTCH :Ascendancy Racing effortless 4-shoe system
CB : 13 T (O'donnell)
WHEELS : O'donnell
DIFFS F/C/R : 10/15/4
SHOCKS F/R : 45/45
SPRINGS F/R: Black/Silver
ADDED STUFF:Team radio tray mod, O'donnell Machined Steering Knuckles and a few other changes. (all hop ups/mods are not needed BTW)
TRUGGY : O'donnell Z01-T
THR SERVO : Savox 1256TG
STR SERVO : Hitec 7955
MOTOR : Alpha S852 (Orange Head)
PIPE : Alpha 0801
RADIO : Airtronics m11
CLUTCH :Ascendancy Racing effortless 4-shoe system
CB : 13 T (O'donnell)
WHEELS : O'donnell
DIFFS F/C/R : 10/15/4
SHOCKS F/R : 45/45
SPRINGS F/R: Black/Silver
ADDED STUFF:Team radio tray mod, O'donnell Machined Steering Knuckles and a few other changes. (all hop ups/mods are not needed BTW)
10-20-2010, 01:38 AM
#61
Senior Member
Thread Starter
Join Date: Feb 2008
Location: Tulsa,
OK
Posts: 344
Likes: 0
Received 0 Likes
on
0 Posts
RE: Your TRUGGY and your setup
ORIGINAL: jmaxey51
New Truggy:
TRUGGY : O'donnell Z01-T
THR SERVO : Savox 1256TG
STR SERVO : Hitec 7955
MOTOR : Alpha S852 (Orange Head)
PIPE : Alpha 0801
RADIO : Airtronics m11
CLUTCH : Ascendancy Racing effortless 4-shoe system
CB : 13 T (O'donnell)
WHEELS : O'donnell
DIFFS F/C/R : 10/15/4
SHOCKS F/R : 45/45
SPRINGS F/R: Black/Silver
ADDED STUFF: Team radio tray mod, O'donnell Machined Steering Knuckles and a few other changes. (all hop ups/mods are not needed BTW)
New Truggy:
TRUGGY : O'donnell Z01-T
THR SERVO : Savox 1256TG
STR SERVO : Hitec 7955
MOTOR : Alpha S852 (Orange Head)
PIPE : Alpha 0801
RADIO : Airtronics m11
CLUTCH : Ascendancy Racing effortless 4-shoe system
CB : 13 T (O'donnell)
WHEELS : O'donnell
DIFFS F/C/R : 10/15/4
SHOCKS F/R : 45/45
SPRINGS F/R: Black/Silver
ADDED STUFF: Team radio tray mod, O'donnell Machined Steering Knuckles and a few other changes. (all hop ups/mods are not needed BTW)
10-20-2010, 06:48 AM
#62
Junior Member
Join Date: Jul 2010
Location: Bristol,
VA
Posts: 26
Likes: 0
Received 0 Likes
on
0 Posts
RE: Your TRUGGY and your setup
I can say 5-6 months into my K8T Pro, it is STILL an awesome Truggy! NOTHINGBROKE! Did have a rear diff issue a while back, but that was all MYFAULT!
BUGGY wise, (Caster ZX 1.5RPro) is the best handling buggy I've driven in a while. (OF my own stuff!)
Just wished LOCAL racing was still as fired up as it was back then.
BUGGY wise, (Caster ZX 1.5RPro) is the best handling buggy I've driven in a while. (OF my own stuff!)
Just wished LOCAL racing was still as fired up as it was back then.
06-18-2011, 09:34 AM
#63
Junior Member
Join Date: Mar 2011
Location: merced,
CA
Posts: 5
Likes: 0
Received 0 Likes
on
0 Posts
RE: Your TRUGGY and your setup
TRUGGY : HYPER ST PRO
STR SERVO :FUTABAS9350
THRSERVO : Hitec 7954
MOTOR :HMMM PICCO P7-.21-OR-PICCO .28 -OR COLLARI .32 I TRADE AT RANDOM
PIPE : JP-1-2-3-4
RADIO : 4PL FUTABA
CLUTCH : WERKS 4 SHOE MED SPRINGS WOW RPM HOG
CB : 13 T (hotbodies)
WHEELS : PRO-LINE HOLESHOTS I BELIEVE -REMEMBER SUPER NEWBIE
DIFFS F/C/R : STOCK
SHOCKS F/R : STOCK
SPRINGS F/R: STOCK
ONE OF ABOUT 9 TRUGGIES BUT MY FAVORATE ONE SO FAR
[/quote]
11-11-2011, 02:48 AM
#64
Junior Member
Join Date: Nov 2011
Location: Camarillo, CA
Posts: 5
Likes: 0
Received 0 Likes
on
0 Posts
RE: Your TRUGGY and your setup
TRUGGY : Losi 8ight T 2.0
THR SERVO : Hitec HS-5625MG
STR SERVO : Hitec HS-7955TG
MOTOR : Novarossi S21P5XLT
PIPE : Novarossi EFRA 9853
RADIO : Spektrum DX-3S
CLUTCH : Werks 4 shoe adjustable
CB : 13T
WHEELS : AKA I-Beam Hard
DIFFS F/C/R : 7/10/5
SHOCKS F/R : 45/40
11-11-2011, 02:58 AM
#65
Senior Member
Join Date: Mar 2005
Location: Kingston UK, but living in Athens, GREECE
Posts: 18,082
Likes: 0
Received 3 Likes
on
3 Posts
RE: Your TRUGGY and your setup
TRUGGY : Mugen MBX5Te
Brushless Conversion kit: Tekno V3
ESC: Castle Creations Mamba Monster Max
THR SERVO : N/A - Electric brake
STR SERVO : AE DS1015
MOTOR : Castle/Neu 2200kv
PIPE : N/A
RADIO : Futaba 3pk /w Spektrum pro module
CLUTCH : None
CB : 15t
WHEELS : Jconcept
TIRES: Proline Bowtie
Body: MBX6T Jconcept Illuzion Punisher v2
DIFFS F/C/R : 10-20-5
SHOCKS F/R : 50/50
Batteries: Protek 2S 40c 5000mAh x2
Camber: 2* front, 2.5* rear
Toe F/R: +2*/-3*
Brushless Conversion kit: Tekno V3
ESC: Castle Creations Mamba Monster Max
THR SERVO : N/A - Electric brake
STR SERVO : AE DS1015
MOTOR : Castle/Neu 2200kv
PIPE : N/A
RADIO : Futaba 3pk /w Spektrum pro module
CLUTCH : None
CB : 15t
WHEELS : Jconcept
TIRES: Proline Bowtie
Body: MBX6T Jconcept Illuzion Punisher v2
DIFFS F/C/R : 10-20-5
SHOCKS F/R : 50/50
Batteries: Protek 2S 40c 5000mAh x2
Camber: 2* front, 2.5* rear
Toe F/R: +2*/-3*
05-22-2012, 05:49 PM
#68
Senior Member
Join Date: Jun 2007
Location: Plainfield,
IL
Posts: 7,163
Likes: 0
Received 0 Likes
on
0 Posts
RE: Your TRUGGY and your setup
Just in and i lucked out bigtime (finally!)
Jammin CRT X1 Pro kit
novarossi P5X buggy engine
jammin JP-3 hard-coat pipe
z-brace and aluminum chassis braces
proline crime fighter tires
hitec HS-985 coreless karbonite throttle servo
hitec HS5955TG coreless titanium steering servo
blue springs
2.5R toe
1.5F toe out
3? rear camber
1 front camber
gearing- stock
diff oil ??? very thick in center???
I will have to test and tune myself, these specs where from the previous owner.
Jammin CRT X1 Pro kit
novarossi P5X buggy engine
jammin JP-3 hard-coat pipe
z-brace and aluminum chassis braces
proline crime fighter tires
hitec HS-985 coreless karbonite throttle servo
hitec HS5955TG coreless titanium steering servo
blue springs
2.5R toe
1.5F toe out
3? rear camber
1 front camber
gearing- stock
diff oil ??? very thick in center???
I will have to test and tune myself, these specs where from the previous owner.
08-25-2012, 07:55 AM
#69
Senior Member
RE: Your TRUGGY and your setup
Well, I had been thinking about getting some cheap Ansmann, new.. But I finally found a deal on an Associated RC8T CE. Just got it today, and spent all morning swapping in ethe engine and electronics, etc.. from the RC8.2. Engines are gonna' be a modded Nosram(Picco), an Argus A52, and an RB Fire 11. Supposedly has 3.5 liters on it, and I got it for €228 shipped (new is €500), with a few spares, etc.. Looks pretty good.. Hopefully I'll be able to test it 2moro...
09-29-2012, 02:25 PM
#70
Junior Member
Join Date: Jun 2012
Location: East hartford,
CT
Posts: 5
Likes: 0
Received 0 Likes
on
0 Posts
RE: Your TRUGGY and your setup
TRUGGY : Losi 8ight T 2.0 Race Roller
THR SERVO : Traxxas 2075 ( Waterproof, 133oz, .18 sec)
STR SERVO : Airtronics 94851 (Dual BB, 196oz, .19 sec)
MOTOR : SH PT28XM1-P8
THR SERVO : Traxxas 2075 ( Waterproof, 133oz, .18 sec)
STR SERVO : Airtronics 94851 (Dual BB, 196oz, .19 sec)
MOTOR : SH PT28XM1-P8
PIPE : SH SA219FS EFRA 2075
RADIO : Spektrum DX3C
CLUTCH : Werks Pro Clutch (Medium Weight 34mm Flywheel)
CB : 16t
WHEELS : ProLine VTR 4.0 Revolver M3
DIFFS F/C/R : 7/10/20
SHOCKS F/R :35/32.5
DROOP F/R :
RIDE HEIGHT : 39mm front and 42mm rear
CAMBER F/R :-1.5/-2
RADIO : Spektrum DX3C
CLUTCH : Werks Pro Clutch (Medium Weight 34mm Flywheel)
CB : 16t
WHEELS : ProLine VTR 4.0 Revolver M3
DIFFS F/C/R : 7/10/20
SHOCKS F/R :35/32.5
DROOP F/R :
RIDE HEIGHT : 39mm front and 42mm rear
CAMBER F/R :-1.5/-2
02-26-2013, 10:57 PM
#71
Senior Member
RE: Your TRUGGY and your setup
Well the above RC8T turned out to have more like 35 liters on it. I have never seen such a ragged out ebay POS... You win some and you lose some.. I definitely lost that one.. [
] Anyway, I've now completely built it up new from ebay chop shops - chassis, diffs, shocks, A-D plates, tank, etc.. Only thing held over are a few screws, the shock towers(have new ones, but was too lazy to replace..), top plate, and radio tray.. Everything else is brand new. So, here we go again...
Team Associated RC8T CE
RB Fire 11/2058, modded Nosram RS.21RR/086, Argus A52/0801, stock clutch for the moment
Hitec 5955 steering, Kopropo somethingorother on gas/brake
Jconcepts Crosshairs and AKA Ibeams
Sanwa MX-V
Have my sights on an Alpha A352 as my new engine for this year.. Got to wait on funds, the right deal, timing, etc..
] Anyway, I've now completely built it up new from ebay chop shops - chassis, diffs, shocks, A-D plates, tank, etc.. Only thing held over are a few screws, the shock towers(have new ones, but was too lazy to replace..), top plate, and radio tray.. Everything else is brand new. So, here we go again...Team Associated RC8T CE
RB Fire 11/2058, modded Nosram RS.21RR/086, Argus A52/0801, stock clutch for the moment
Hitec 5955 steering, Kopropo somethingorother on gas/brake
Jconcepts Crosshairs and AKA Ibeams
Sanwa MX-V
Have my sights on an Alpha A352 as my new engine for this year.. Got to wait on funds, the right deal, timing, etc..
03-01-2013, 07:00 AM
#72
RE: Your TRUGGY and your setup
TRUGGY : D8T
THR SERVO : Hitec 7945
STR SERVO : Hitec 7955
MOTOR : OS .25XZ
PIPE : 086
RADIO : Spectrum DX3C
CLUTCH : Stock
CB : 13t
WHEELS : JConcepts Sevens Halves-Up (soft)
DIFFS F/C/R : 7-7-5
SHOCKS F/R :40/50
DROOP F/R : About 1/2 (eyeballed). ;-)
RIDE HEIGHT : 27mm
CAMBER F/R : ~ -1
BODY/WING: ProLine Bulldog
THR SERVO : Hitec 7945
STR SERVO : Hitec 7955
MOTOR : OS .25XZ
PIPE : 086
RADIO : Spectrum DX3C
CLUTCH : Stock
CB : 13t
WHEELS : JConcepts Sevens Halves-Up (soft)
DIFFS F/C/R : 7-7-5
SHOCKS F/R :40/50
DROOP F/R : About 1/2 (eyeballed). ;-)
RIDE HEIGHT : 27mm
CAMBER F/R : ~ -1
BODY/WING: ProLine Bulldog
03-03-2013, 10:24 AM
#73
Senior Member
Join Date: Mar 2008
Location: Miami, FL
Posts: 109
Likes: 0
Received 0 Likes
on
0 Posts
RE: Your TRUGGY and your setup
TRUGGY : Mugen mbx6t E
STR SERVO : Savox 1256 tg
MOTOR : t8 1700 kv truggy motor
ESC : rx8
GEARING : 18/46
RADIO : Flysky gt2b
WHEELS : duratrax xcons
DIFFS F/C/R : 10/10/10
SHOCKS F/R : 45/40
DROOP F/R : haven't measured
CAMBER F/R : -2/-1
image by Robgdds
image by Robgdds
image by Robgdds
image by Robgdds
STR SERVO : Savox 1256 tg
MOTOR : t8 1700 kv truggy motor
ESC : rx8
GEARING : 18/46
RADIO : Flysky gt2b
WHEELS : duratrax xcons
DIFFS F/C/R : 10/10/10
SHOCKS F/R : 45/40
DROOP F/R : haven't measured
CAMBER F/R : -2/-1
image by Robgdds
image by Robgdds
image by Robgdds
image by Robgdds
05-13-2013, 08:30 PM
#74
Senior Member
My Feedback: (5)
Join Date: Jan 2005
Location: Lisbon,
CT
Posts: 129
Likes: 0
Received 0 Likes
on
0 Posts
RE: Your TRUGGY and your setup
TRUGGY : Tamiya TRF801xt with some of the performance kit parts
THR SERVO : Futaba S9351
STR SERVO :Futaba S9351
MOTOR : OS .28XZ
PIPE : O.S. T-2060SC WN
RADIO : Futaba 3PK
CLUTCH : Stock
CB : stock
WHEELS : AKA premounted micro pin
DIFFS F/C/R : 7k - 10k - 3k
SHOCKS F/R :40/50
DROOP F/R : a lot
RIDE HEIGHT : not enough haha.
CAMBER F/R : 0 / -1
BODY/WING: Stock Tamiya
THR SERVO : Futaba S9351
STR SERVO :Futaba S9351
MOTOR : OS .28XZ
PIPE : O.S. T-2060SC WN
RADIO : Futaba 3PK
CLUTCH : Stock
CB : stock
WHEELS : AKA premounted micro pin
DIFFS F/C/R : 7k - 10k - 3k
SHOCKS F/R :40/50
DROOP F/R : a lot
RIDE HEIGHT : not enough haha.
CAMBER F/R : 0 / -1
BODY/WING: Stock Tamiya
03-18-2014, 06:53 AM
#75
My Feedback: (17)
Join Date: Apr 2004
Location: Little Elm,
TX
Posts: 13
Likes: 0
Received 0 Likes
on
0 Posts
TRUGGY : Tamiya TRF801XT
THR SERVO : N/A
STR SERVO : Pro Tek 100T
MOTOR : Hobbywing 2000kv Sensored
PIPE : N/A
RADIO : Spektrum DX3c
CLUTCH : N/A
CB : 13t pinion
WHEELS : Proline VTR wheels with Proline Hole Shots
DIFFS F/C/R : 7/10/3
SHOCKS F/R : Tamiya Stock Springs, 35.7 F&R
DROOP F/R : n/a
RIDE HEIGHT : Arms Level
CAMBER F/R : -2F/-1.5R
THR SERVO : N/A
STR SERVO : Pro Tek 100T
MOTOR : Hobbywing 2000kv Sensored
PIPE : N/A
RADIO : Spektrum DX3c
CLUTCH : N/A
CB : 13t pinion
WHEELS : Proline VTR wheels with Proline Hole Shots
DIFFS F/C/R : 7/10/3
SHOCKS F/R : Tamiya Stock Springs, 35.7 F&R
DROOP F/R : n/a
RIDE HEIGHT : Arms Level
CAMBER F/R : -2F/-1.5R
Last edited by timberline97; 03-24-2014 at 11:06 AM.
