Go Back  RCU Forums > RC Airplanes > RC Warbirds and Warplanes
Reload this Page >

Ziroli 1/6 Hellcat Build

Notices
RC Warbirds and Warplanes Discuss rc warbirds and warplanes in this forum.

Ziroli 1/6 Hellcat Build

Old 03-14-2024, 09:34 AM
  #351  
shakeel khan
Junior Member
 
Join Date: Mar 2024
Posts: 1
Received 0 Likes on 0 Posts
Default

During the construction process, I utilized the magnetic building method from Airfield Models - Radio Control Flying Aircraft and Display. This method has proven to be exceptionally efficient, and I'm thoroughly impressed with its effectiveness. It's my first time utilizing this system, and I can confidently say that I won't build another plane without it.

With the assistance of the PicsArt editor, I was able to design and visualize the wing structure, ensuring that it meets my specifications and preferences. This tool has been invaluable in creating a visually appealing and structurally sound wing assembly.
Old 03-15-2024, 08:38 AM
  #352  
DaleCS
Thread Starter
 
DaleCS's Avatar
 
Join Date: Aug 2002
Location: Novi, MI
Posts: 292
Received 3 Likes on 3 Posts
Default

Originally Posted by shakeel khan
During the construction process, I utilized the magnetic building method from Airfield Models - Radio Control Flying Aircraft and Display. This method has proven to be exceptionally efficient, and I'm thoroughly impressed with its effectiveness. It's my first time utilizing this system, and I can confidently say that I won't build another plane without it.

With the assistance of the PicsArt editor, I was able to design and visualize the wing structure, ensuring that it meets my specifications and preferences. This tool has been invaluable in creating a visually appealing and structurally sound wing assembly.
Hello Shakeel,

I used the same method. Unfortunately, I didn't post any pictures of building the wing this way. I had the wing built before starting this thread. However, on the first page of this thread, there are a few pictures of the h-stab being built with these magnetic fixtures. I agree, these are very useful and I recommend them.
Old 03-27-2024, 06:25 PM
  #353  
DaleCS
Thread Starter
 
DaleCS's Avatar
 
Join Date: Aug 2002
Location: Novi, MI
Posts: 292
Received 3 Likes on 3 Posts
Default

Up to around 8,600 rivets applied, just on the wing and belly-pan. I think I could easily put another 2, 000 into the wing, but I may shoot for 600 more. IFF I can stop at 9,000, I'll have about 6500 left for the fuselage - or I'll need to order some more.

What's is a good number to stop at? When is enough good enough?

I currently have a couple ideas I'm using as guidelines:
- no large expanses without rivets (it should look like something is holding the panel in place to the underlying structure - edges and at least a couple rows down and across the panel)
- outline access panels (the panels have dummy screws or rivets - the surrounding metal should not be left flapping in the wind)
- interesting features (there's a curved line of rivets on each side of the center wing section, and some lines fanned out from where the full scale wing would break for rotating into storage position - things that make the Hellcat unique)

At one point, the wing obviously looked deficient on rivet count. Now, it's looking much better, filled in.

Any thoughts on this? If this were a museum piece, then of course, "Put them all on!"

My Byron Hellcat had zero dummy rivets, zero dummy screws, zero dummy panels, etc. and yet it all got great comments and a purchase offer. And yes, this custom build has been a riveting experience!
Old 03-30-2024, 01:49 PM
  #354  
DaleCS
Thread Starter
 
DaleCS's Avatar
 
Join Date: Aug 2002
Location: Novi, MI
Posts: 292
Received 3 Likes on 3 Posts
Default

9,000 rivets...

I think the upper wing panels are done. Will flip it, today, as I think I need a couple more lines on the underside. Then the inboard flaps. Maybe a couple short lines on each gun/ammo access cover. Have I done every line of rivets? No. But standing back, there is a fullness that wasn't there before, that feels acceptable. I feel that if I go further than I'm all in - one more line and it won't be balanced - to be balanced I'd have to add 10 lines here, 8 lines there repeat on other side... another 4,0000 on the wing? So, I may have enough, now. Stop. Move on.

Will I need to order more rivets for the fuse, h/v stab? We shall see as I have about 6,000 left. It may be close.

Old 03-31-2024, 08:40 AM
  #355  
DaleCS
Thread Starter
 
DaleCS's Avatar
 
Join Date: Aug 2002
Location: Novi, MI
Posts: 292
Received 3 Likes on 3 Posts
Default

Left wing, inboard flap - rivets completed. One line on the right outboard wing bottom and the right inboard flap to complete and the entire wing will then be done (other than 4 bay covers I need to fabricate and completion of the gear covers).

Yes, I could do more rivets on the wing, but time to move on. I think it's looking good.

Any thoughts?

I'll need to start looking for paint, going back through my bookmarks. I used an air spray gun (not an air brush) and latex paint last time. I have a single stage air brush and have been thinking about an upgrade to a dual stage.

!

Old 04-10-2024, 05:17 PM
  #356  
DaleCS
Thread Starter
 
DaleCS's Avatar
 
Join Date: Aug 2002
Location: Novi, MI
Posts: 292
Received 3 Likes on 3 Posts
Default

Fuselage progress: Butt panel joints at front of fuse are complete, along with two sets each on the vertical and horizontal stabs. Also, three overlapping panel joints completed at the cockpit area of the fuse.

I tried using electrical tape for the overlapping panel joints, as it is the same thickness (7 mils) as the ChartPak tap used for the butt joints. However, I found the adhesive too aggressive and that the solvent in the paint would slowly curl the tape. Not good. I had decided against using "painter tape" as it was half the thickness of the ChartPak tape - I didn't think I'd get enough paint build-up to make a clearly defined line.

So, time for an idea: Layer two pieces of painter tape and cut it down the middle to get a clean, straight edge. This worked extremely well.

Weather is warming up, so hopefully I can get at least 3 of these lines done per day, as long as it doesn't rain. The overlapping joints take time as I haven't figured out how to paint more than one tape area at a time - finish one area, remove the tap and where the tape is removed, it get's blended into the next area. I might be able to tape the whole thing at once, spray and then remove one tape, spray, and keep repeating until all the tape is removed. But, I might not finish in one day and I don't want to leave the tape on too long - even though the painter tape's adhesion is much less than the electrical tape, it isn't zero and does pull a pit of the primer with it. I prefer to put the tape on, spray, let it set for an hour max, and then remove it.

Better ideas welcomed.



Old 04-11-2024, 08:14 AM
  #357  
G.F. Reid
My Feedback: (1)
 
G.F. Reid's Avatar
 
Join Date: Dec 2001
Location: Palmetto, GA
Posts: 865
Received 0 Likes on 0 Posts
Default

One way I've seen it done is with masking tape and spackle. Place the tape where you want it, apply the spackle against the edge, sand and remove the tape. Sand the edges from front to back and top to bottom. Took it from an an old copy of "Scale R\C Modeler" years ago.
Great job on one of my all time favorite planes by the way!
Old 04-15-2024, 09:42 AM
  #358  
DaleCS
Thread Starter
 
DaleCS's Avatar
 
Join Date: Aug 2002
Location: Novi, MI
Posts: 292
Received 3 Likes on 3 Posts
Default

Originally Posted by G.F. Reid
One way I've seen it done is with masking tape and spackle. Place the tape where you want it, apply the spackle against the edge, sand and remove the tape. Sand the edges from front to back and top to bottom. Took it from an an old copy of "Scale R\C Modeler" years ago.
Great job on one of my all time favorite planes by the way!
That sounds like a good way to ensure consistent edge heights. I also like the idea for using something other than paint, something that may be low or zero VOC. Perhaps for the next build? Will see. Must get this one finished!
Old 04-15-2024, 10:23 AM
  #359  
Chad Veich
My Feedback: (60)
 
Join Date: Dec 2001
Location: Litchfield Park, AZ
Posts: 7,677
Likes: 0
Received 25 Likes on 23 Posts
Default

Originally Posted by G.F. Reid
One way I've seen it done is with masking tape and spackle. Place the tape where you want it, apply the spackle against the edge, sand and remove the tape. Sand the edges from front to back and top to bottom. Took it from an an old copy of "Scale R\C Modeler" years ago.
Great job on one of my all time favorite planes by the way!
Exactly the way I did it on my Hellcat except that I used electrical tape and spot putty. I like the electrical tape because it can be formed around compound curves and you can wet sand against it without it falling apart. The spot putty works well but next time I will probably use Evercoat body filler as it is a bit tougher. There were a few spots on the spot putty that chipped out and had to be repaired.








Old 04-15-2024, 11:05 AM
  #360  
G.F. Reid
My Feedback: (1)
 
G.F. Reid's Avatar
 
Join Date: Dec 2001
Location: Palmetto, GA
Posts: 865
Received 0 Likes on 0 Posts
Default

Hello Chad! As you can see the bug came back....lol
Old 04-15-2024, 03:39 PM
  #361  
Chad Veich
My Feedback: (60)
 
Join Date: Dec 2001
Location: Litchfield Park, AZ
Posts: 7,677
Likes: 0
Received 25 Likes on 23 Posts
Default

Originally Posted by G.F. Reid
Hello Chad! As you can see the bug came back....lol
Always good to hear from you Greg! I think I have known you for about as long as I have known anybody on these boards. If I am not mistaken we first started interacting here way back when it was RC Online and the Internet was a fairly new idea! Man, where does the time go? Are you working on anything currently or just back perusing the threads? Either way I hope all is going well for you and yours my friend.
Old 04-15-2024, 03:56 PM
  #362  
G.F. Reid
My Feedback: (1)
 
G.F. Reid's Avatar
 
Join Date: Dec 2001
Location: Palmetto, GA
Posts: 865
Received 0 Likes on 0 Posts
Default

Yes, it has been a long time since those RCO days!
Not working on anything at the time being. Unfortunately I'm battling cancer and it kind of makes you think about all the things you want to do but don't feel like doing and one of them for me was playing with an airplane. So I've got a couple of foamies, some minis and possibly plans to finish that old p-47 one of these days.
Old 04-15-2024, 04:15 PM
  #363  
DaleCS
Thread Starter
 
DaleCS's Avatar
 
Join Date: Aug 2002
Location: Novi, MI
Posts: 292
Received 3 Likes on 3 Posts
Default

Originally Posted by Chad Veich
Exactly the way I did it on my Hellcat except that I used electrical tape and spot putty. I like the electrical tape because it can be formed around compound curves and you can wet sand against it without it falling apart. The spot putty works well but next time I will probably use Evercoat body filler as it is a bit tougher. There were a few spots on the spot putty that chipped out and had to be repaired.
Beautiful work, Chad - I would not have expected less from you. Mine will just be "good enough" in comparison. At least I've learned a lot by pushing through the process.

I've noticed that you are participating more on this forum. I hope this means you are doing better.
Old 04-15-2024, 04:18 PM
  #364  
DaleCS
Thread Starter
 
DaleCS's Avatar
 
Join Date: Aug 2002
Location: Novi, MI
Posts: 292
Received 3 Likes on 3 Posts
Default

Originally Posted by G.F. Reid
Yes, it has been a long time since those RCO days!
Not working on anything at the time being. Unfortunately I'm battling cancer and it kind of makes you think about all the things you want to do but don't feel like doing and one of them for me was playing with an airplane. So I've got a couple of foamies, some minis and possibly plans to finish that old p-47 one of these days.
I hope and pray the best for you. No way forward except through.
The following users liked this post:
G.F. Reid (04-15-2024)
Old 04-15-2024, 11:13 PM
  #365  
G.F. Reid
My Feedback: (1)
 
G.F. Reid's Avatar
 
Join Date: Dec 2001
Location: Palmetto, GA
Posts: 865
Received 0 Likes on 0 Posts
Default

Thank you. Doing things like building and / or buying model planes right now is sort of a testimony the fact that I plan to be around to fly them!
Old 04-16-2024, 11:01 AM
  #366  
Chad Veich
My Feedback: (60)
 
Join Date: Dec 2001
Location: Litchfield Park, AZ
Posts: 7,677
Likes: 0
Received 25 Likes on 23 Posts
Default

Originally Posted by G.F. Reid
Yes, it has been a long time since those RCO days!
Not working on anything at the time being. Unfortunately I'm battling cancer and it kind of makes you think about all the things you want to do but don't feel like doing and one of them for me was playing with an airplane. So I've got a couple of foamies, some minis and possibly plans to finish that old p-47 one of these days.
I am really sorry Greg, I hope that your battle will result in a full and complete recovery. I've not had to face Cancer but I can surely commiserate with having the desire to do something but not the energy. This is pretty much the definition of life for somebody with my disease. Getting old sure can be a challenge! We too will keep you in our prayers Greg and wish you all the best.
Old 04-16-2024, 01:50 PM
  #367  
G.F. Reid
My Feedback: (1)
 
G.F. Reid's Avatar
 
Join Date: Dec 2001
Location: Palmetto, GA
Posts: 865
Received 0 Likes on 0 Posts
Default

Thank you Chad. Likewise to you...prayers for you and yours.
Now, back to building... What grit paper are you using against that electrical tape that won't chew it up?

Last edited by G.F. Reid; 04-16-2024 at 01:53 PM.
Old 04-27-2024, 08:25 AM
  #368  
PNW Tim
Junior Member
 
Join Date: May 2022
Posts: 7
Received 0 Likes on 0 Posts
Default

Dale - I have spent the last 3 or 4 days reading your build thread and what a journey! Through the pandemic and beyond! I too have recently retired and after a 35 year hiatus am getting back into RC and working my way through all the changes. Going to cut my teeth on a TF Corsair which I have always been enamored of and move on from there. Your build thread is awesome and your patience and skills are a testimony to what can be created with the right amount of focus and effort. Although your build is significantly more complex that what I am planning I have already learned many things from you and save several links to pages and websites I know I will be using/visiting in the future. Keep up the good work and will follow till the maiden voyage.
Old 05-08-2024, 08:08 AM
  #369  
DaleCS
Thread Starter
 
DaleCS's Avatar
 
Join Date: Aug 2002
Location: Novi, MI
Posts: 292
Received 3 Likes on 3 Posts
Default

Originally Posted by PNW Tim
Dale - I have spent the last 3 or 4 days reading your build thread and what a journey! Through the pandemic and beyond! I too have recently retired and after a 35 year hiatus am getting back into RC and working my way through all the changes. Going to cut my teeth on a TF Corsair which I have always been enamored of and move on from there. Your build thread is awesome and your patience and skills are a testimony to what can be created with the right amount of focus and effort. Although your build is significantly more complex that what I am planning I have already learned many things from you and save several links to pages and websites I know I will be using/visiting in the future. Keep up the good work and will follow till the maiden voyage.
Thank you for the kind words, Tim!

Patience, I have much of, true. Skills - I will likely never match those of ChadV, Mirce and many others that have posted here. Thankful for the time you spent reviewing my build. I'm glad you are finding useful content here, much being the summary of what I've learned from others. It has taken way too long, but I've learned much, met some good people with great input, and it has been a refuge at times. Delayed by having too many interests, besides the big life issues.

Due to weather, I'm taking a break from Spring yard work, today, and will get some panel lines done on the fuse, today. Lines for the fin, stab and cockpit forward are done. My method for completing the overlap panel joints on the fuse is slow - slow, but it works: Mask and paint one panel line, feathering into the previous line, repeat. Perhaps I could mask all the lines, paint, remove the tape and feather in with sanding? Will see. I have a process, it's working, and I have other tasks around the house to complete while paint dries! If doing overlapping panel lines on another project, I will seriously consider ChadV's method.

Again, thank you!


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Manage Preferences - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.