Go Back  RCU Forums > RC Airplanes > Scratch Building, Aircraft Design, 3D/CAD
Reload this Page >

Looking for PDF Plans for a Swizzle Stick / Stick .40

Notices
Scratch Building, Aircraft Design, 3D/CAD If you are starting/building a project from scratch or want to discuss design, CAD or even share 3D design images this is the place. Q&A's.

Looking for PDF Plans for a Swizzle Stick / Stick .40

Old 05-19-2013, 09:39 PM
  #1  
SnApRoLl-
Senior Member
Thread Starter
 
Join Date: Apr 2002
Location: middle of nowhere, MD
Posts: 232
Likes: 0
Received 0 Likes on 0 Posts
Default Looking for PDF Plans for a Swizzle Stick / Stick .40

Hello all,
Not sure if this is the right forum or not, but does anyone have or know where I can download a free set of PDF or even .dxf or .dwg plans for the old Swizzle Stick / Stick .40? I've done quite a bit of searching but no luck.

Thanks,
Shawn
Old 05-20-2013, 07:23 AM
  #2  
FlyerInOKC
My Feedback: (6)
 
FlyerInOKC's Avatar
 
Join Date: Nov 2004
Location: Oklahoma City, OK
Posts: 10,992
Likes: 0
Received 19 Likes on 19 Posts
Default RE: Looking for PDF Plans for a Swizzle Stick / Stick .40

It has been a long time since I have seen a swizzle stik. They were a pretty basic airplanes if I remember right there were two planes with that name one was US design with a simple stick rear fuselage and a UK version similar to the Ugly Stik. I believe Ace made a simolar airplane I just can't remember the name. If you can find someone with the old Ace plans you might find something you like. It seems I inherted a set of the Ace plans but I have no idea where to find them.
Old 05-20-2013, 10:50 AM
  #3  
SnApRoLl-
Senior Member
Thread Starter
 
Join Date: Apr 2002
Location: middle of nowhere, MD
Posts: 232
Likes: 0
Received 0 Likes on 0 Posts
Default RE: Looking for PDF Plans for a Swizzle Stick / Stick .40

The plans I'm looking for are the pretty much the same as the Balsa USA Stick 40 Plus. The fuse and engine mount are made up of 2 long square pieces of hardwood with almost square flat sides for the wing saddle and the radio gear. I know it's a very simple plane to build, but I need plans so I can get the proper dimensions and wing incidence if any as well as rib templates as I am going to cut a foam core wing.

Here is a picture of one.

Thanks,
Shawn

Attached Thumbnails Click image for larger version

Name:	Hf10163.jpg
Views:	479
Size:	52.6 KB
ID:	1883690  
Old 01-09-2015, 01:41 AM
  #4  
Kwooda
Junior Member
 
Kwooda's Avatar
 
Join Date: Apr 2004
Location: Smartville, CA
Posts: 2
Likes: 0
Received 0 Likes on 0 Posts
Default

Are you still looking for plans? I don't have a PDF but could send a copy of full size plans. That's actually my photo you've got there.
Old 01-09-2015, 07:02 AM
  #5  
foodstick
 
foodstick's Avatar
 
Join Date: Mar 2005
Location: ankeny, IA
Posts: 5,557
Likes: 0
Received 0 Likes on 0 Posts
Default

look around here.. I will warn you though it si going to give you LOTS of ideas !

http://www.outerzone.co.uk/index.asp
Old 01-09-2015, 08:11 AM
  #6  
FlyerInOKC
My Feedback: (6)
 
FlyerInOKC's Avatar
 
Join Date: Nov 2004
Location: Oklahoma City, OK
Posts: 10,992
Likes: 0
Received 19 Likes on 19 Posts
Default

Originally Posted by SnApRoLl- View Post
The plans I'm looking for are the pretty much the same as the Balsa USA Stick 40 Plus. The fuse and engine mount are made up of 2 long square pieces of hardwood with almost square flat sides for the wing saddle and the radio gear. I know it's a very simple plane to build, but I need plans so I can get the proper dimensions and wing incidence if any as well as rib templates as I am going to cut a foam core wing.
Thanks,
Shawn
I had a friend, long gone, that flew a couple of these, they were a favorite of his!
Old 01-09-2015, 01:20 PM
  #7  
eromeros
Member
 
Join Date: Feb 2004
Location: monterreymonterrey, MEXICO
Posts: 65
Likes: 0
Received 0 Likes on 0 Posts
Default

Not exactly what you were looking for but pretty close.
http://www.rcgroups.com/forums/showt...233857&page=88
Old 01-10-2015, 12:58 PM
  #8  
MrMulligan
My Feedback: (314)
 
Join Date: Feb 2002
Location: Keyport, NJ
Posts: 1,099
Likes: 0
Received 0 Likes on 0 Posts
Default

The plans for this were originally published by RCM. Their plans are available but a bit of a hassle according to what I've read here. I built a .20 sized one and a BUSA Swizzle Stik, .40 size. They were a good use for a spare wing.

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.