RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: mike_r
Showing results 1 to 11 of 11
Search took 0.12 seconds.
Forum: Giant Scale Aircraft - General
03-11-2014, 05:05 PM
Replies: 4
Views: 650
Posted By mike_r

Thanks! Tried that... Servo worked... And...

Thanks!

Tried that... Servo worked... And somehow along the way everything started working?
Forum: Giant Scale Aircraft - General
03-11-2014, 03:00 PM
Replies: 4
Views: 650
Posted By mike_r

Ignition Battery Eliminator Troubleshooting

Bought a ignition battery eliminator for my Aviation Models Yak 54 30%. Receiver is a AR8000 with redundant batteries... The only open channel is the gear channel. Plugged in there but can't get...
Forum: JR Radio & Spektrum Radios
02-28-2014, 02:01 PM
Replies: 2
Views: 889
Posted By mike_r

AR8000 Issues

I bought used a Spektrum ar8000 months ago online. Finally got my Yak 54 50cc build enough to start testing the servos. After binding with my Dx7s radio, there occasionally is a red light that...
Forum: Questions and Answers
02-28-2014, 01:58 PM
Replies: 2
Views: 3,295
Posted By mike_r

Thanks for the help! I think it is a continual...

Thanks for the help! I think it is a continual flashing red light... Will stand farther away from the receiver.

Also will post in Spektrum.
Forum: Questions and Answers
02-28-2014, 01:18 PM
Replies: 2
Views: 3,295
Posted By mike_r

ar8000 Spektrum Receiver Issue

I bought used a Spektrum ar8000 months ago online. Finally got my Yak 54 50cc build enough to start testing the servos. After binding with my Dx7s radio, there occasionally is a red light that...
Forum: Questions and Answers
12-09-2013, 10:02 PM
Replies: 15
Views: 4,465
Posted By mike_r

Jester_s1--Thanks for your input! That makes a...

Jester_s1--Thanks for your input! That makes a lot of sense. Will definitely remember this experience!

Sending the engine out tomorrow. Hopefully you won't see a post about it again! =D

Thanks...
Forum: Questions and Answers
12-08-2013, 03:29 PM
Replies: 15
Views: 4,465
Posted By mike_r

Jester_s1--We physically moved the HSN from the...

Jester_s1--We physically moved the HSN from the remote location to right by the carborator. The instructor was thinking that would help. It seemed to run better, but some time later it started...
Forum: Questions and Answers
12-05-2013, 11:26 AM
Replies: 15
Views: 4,465
Posted By mike_r

I just spoke with Horizon Hobby. If it is more...

I just spoke with Horizon Hobby. If it is more that an air leak with the HSN o-ring or carb o-ring they want me to send it in--which I will do since I don't want to compromise whatever warranty comes...
Forum: Questions and Answers
12-05-2013, 08:38 AM
Replies: 15
Views: 4,465
Posted By mike_r

Thanks for the replies! Iron Bottom--that...

Thanks for the replies!

Iron Bottom--that needle has a weird setup that does not allow it to be over adjusted. I have been messing with it, so I will set it between the two points for starters....
Forum: Questions and Answers
12-05-2013, 04:10 AM
Replies: 15
Views: 4,465
Posted By mike_r

I ran one tank through it on the ground (the book...

I ran one tank through it on the ground (the book on the engine said nothing about break-in). It was at half-throttle max until the end of the tank. Then I took it to the field and an instructor had...
Forum: Questions and Answers
12-04-2013, 10:39 PM
Replies: 15
Views: 4,465
Posted By mike_r

New Nitro Engine Revving Up and Down

Hello,

I just purchased a Hangar 9 Alpha 40 with the Evo .52 engine. I've started it with brand new fuel, but when start to rev up the engine starts to rev up and down quite a bit. It will often...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.