RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Search
Today's Posts
Mark Forums Read
Vendor Directory
Notices
Search: Posts Made By: arjan70
Showing results 1 to 11 of 11
Search took 0.06 seconds.
Forum: Turbine Clinic
02-23-2024, 05:48 AM
Replies: 0
Views: 171
Posted By arjan70

Evojet 220B 180 Keroburner

Recently I bought an crashed Evojet 220 turbine, according to the owner the cost for repair were almost equal to a new engine.
Unfortunatly they took out some parts at the service inspection and...
Forum: RC Jets
02-23-2024, 05:44 AM
Replies: 90
Views: 24,123
Posted By arjan70

Gary, thanks alot for you help last year, I...

Gary, thanks alot for you help last year, I was able to receive the new springs for the retracts from Feiboa :)
Forum: RC Jets
02-23-2024, 05:42 AM
Replies: 90
Views: 24,123
Posted By arjan70

Thanks alot for your support last year , I have...

Thanks alot for your support last year , I have made the airbrakes with a servo now which is much better now almost 85 degrees max :)
Forum: RC Jets
02-23-2024, 05:38 AM
Replies: 3,661
Views: 624,704
Posted By arjan70

Roughly I balancing the rotor first but then...

Roughly I balancing the rotor first but then balancing the whole engine ,more accurate when bearings are seated in the shaft
Forum: RC Jets
02-23-2024, 05:32 AM
Replies: 3,661
Views: 624,704
Posted By arjan70

I have made a solid aluminium cradle, balancing...

I have made a solid aluminium cradle, balancing comes close to 2mg now.
Forum: RC Jets
04-17-2022, 12:06 PM
Replies: 2,625
Views: 735,151
Posted By arjan70

You mean full flap with 15% elevator down or 3 mm...

You mean full flap with 15% elevator down or 3 mm down elevator, sorry for asking
Forum: RC Jets
04-17-2022, 10:24 AM
Replies: 2,625
Views: 735,151
Posted By arjan70

Thanks alot Dave, and when you would fly with...

Thanks alot Dave, and when you would fly with full flaps ( crawling ) how far down for the elevator ? in my boomerang manual they advice 15% down which I don't dare
Forum: RC Jets
04-17-2022, 09:51 AM
Replies: 2,625
Views: 735,151
Posted By arjan70

Hello , i,m searching for aome answers...

Hello , i,m searching for aome answers regarding flaps : When using flaps during take off , do we need also to hve some elevator down? or just flaps 20-25mm.
What about slow flight and...
Forum: RC Jets
07-10-2020, 03:04 PM
Replies: 3,661
Views: 624,704
Posted By arjan70

Hello Dazz, Are you spinning the rotor with...

Hello Dazz,

Are you spinning the rotor with compresses air or with a motor drive and is your cradle sensitive enough to reach such low values and if re calibrate are you finding the same results?...
Forum: RC Jets
02-28-2020, 12:30 PM
Replies: 90
Views: 24,123
Posted By arjan70

Thanks alot Gary , Fantastic camerawork and...

Thanks alot Gary , Fantastic camerawork and pilot :) impressive flight
Forum: RC Jets
02-26-2020, 02:05 PM
Replies: 90
Views: 24,123
Posted By arjan70

Nose wheel L-39 FB

Hello Jet Flyers.
I,m rebuilding a L-39 Feibao in Breitling style which had only one flight and landed against the fence at PAMPA.
Try to figure out how the steering servo is connected to the nose...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.