RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: TriadicRC
Showing results 1 to 9 of 9
Search took 0.05 seconds.
09-02-2014, 04:55 AM
Replies: 3
Views: 1,436
Posted By TriadicRC

MGT 3.0, Worth Fixing?

A few years ago i purchased a MGT 3.0 as it was fairly inexpensive and had decent reviews. Out of the box i had nothing but trouble with the engine. It would like to lean out for no real reason....
Forum: HPI Racing
09-01-2014, 04:10 PM
Replies: 8
Views: 2,131
Posted By TriadicRC

it's a T-15 engine. This is really odd because...

it's a T-15 engine. This is really odd because the cars looks dead on like an RS4 RTR 3 Evo, specifically the Dodge Viper model based on the wheels. This particular car uses B021 bearings for the...
08-26-2014, 11:39 AM
Replies: 11
Views: 934
Posted By TriadicRC

That looks like a T-Maxx to me

That looks like a T-Maxx to me
Forum: HPI Racing
08-12-2014, 06:24 AM
Replies: 8
Views: 2,131
Posted By TriadicRC

Do you have calipers or any other semi-accurate...

Do you have calipers or any other semi-accurate way to take measurements of where the bearing resides? HPI uses B021 on the clutch bells for almost every nitro car they make / have ever made. B021...
Forum: HPI Racing
08-11-2014, 02:09 PM
Replies: 1
Views: 1,203
Posted By TriadicRC

It sounds like you adjusted your idle using the...

It sounds like you adjusted your idle using the throttle trim on the remote. You should set your throttle trim to center on the remote, adjust the linkages on the car to be at idle and apply no force...
Forum: HPI Racing
08-11-2014, 01:52 PM
Replies: 4
Views: 1,132
Posted By TriadicRC

The Sprint 2 Drift has a brushed motor so your...

The Sprint 2 Drift has a brushed motor so your not going to get a whole lot more speed out of it without upgrading the ESC and motor to a brushless setup. I don't think the electronics in the...
Forum: HPI Racing
08-11-2014, 01:28 PM
Replies: 8
Views: 2,131
Posted By TriadicRC

Is the bearing too big for the clutch bell? B021...

Is the bearing too big for the clutch bell? B021 is all i can find as well for the RS4. Do you know what the exact model of RS4 this is?
Forum: RC Truggy
08-09-2014, 05:51 AM
Replies: 8
Views: 15,043
Posted By TriadicRC

The weight of the truck shifts to the rear which...

The weight of the truck shifts to the rear which raises the front end. It raises the front end enough that the front wheels have less traction than the rear wheels and all of the engine power gets...
Forum: RC Truggy
08-08-2014, 04:10 PM
Replies: 8
Views: 15,043
Posted By TriadicRC

Truggy Diff Oils

I just recently purchased a HPI Trophy 4.6 truggy and i have to say i am absolutely in love with the truck. I know it's not the best race vehicle out there, but i am slowly replacing parts to get it...
Showing results 1 to 9 of 9


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.