RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Suprawill1
Showing results 1 to 10 of 10
Search took 0.09 seconds.
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
06-04-2020, 11:05 AM
Replies: 0
Views: 271
Posted By Suprawill1

9G Servo Arms

Hi All,
Does anyone know where I can get these? I don't know if all 9G servos have the same splined fitting but I have the Freewing servos.
The arms they come with are 5/8" in length. I'm looking...
Forum: Futaba Radios Direct support forum
05-29-2020, 02:01 PM
Replies: 17
Views: 7,334
Posted By Suprawill1

Yes, exactly. The T10J is a very diverse radio....

Yes, exactly.
The T10J is a very diverse radio. I learned a lot about it in the last couple days.
Forum: Futaba Radios Direct support forum
05-29-2020, 09:58 AM
Replies: 17
Views: 7,334
Posted By Suprawill1

I made most of the adjustments in the Flaperon...

I made most of the adjustments in the Flaperon menu. The only one I made in the Airbrake menu was the switch throw direction. I needed the Airbrakes on switch up and the flaps on switch down. It was...
Forum: Futaba Radios Direct support forum
05-28-2020, 10:29 PM
Replies: 17
Views: 7,334
Posted By Suprawill1

I don't know why but the airbrake mix gives me...

I don't know why but the airbrake mix gives me only 2 choices. Either INH or Off.
I did make some percentage corrections in the flaperon screen. Flap 1 was at -100% and I changed it to +100%. Flap 2...
Forum: Futaba Radios Direct support forum
05-28-2020, 09:46 PM
Replies: 17
Views: 7,334
Posted By Suprawill1

I believe I have both activated. I've got the...

I believe I have both activated. I've got the flaperons on "ACT" and the airbrakes on "INH". The only other option on the airbrakes Mix is "Off".
Forum: Futaba Radios Direct support forum
05-28-2020, 08:12 PM
Replies: 17
Views: 7,334
Posted By Suprawill1

From what I understand, the flaps are controlled...

From what I understand, the flaps are controlled by the VR rotary knob if the flaps are separate from the ailerons. In my case, I am using the ailerons also as flaps so they are electronically mixed...
Forum: Futaba Radios Direct support forum
05-28-2020, 05:37 PM
Replies: 17
Views: 7,334
Posted By Suprawill1

Thanks for the hit Bill. I wish it was that...

Thanks for the hit Bill.
I wish it was that easy. :) It's not the direction of travel that's the problem. The switching is reversed. The aileron stick is controlling the flaps instead of the...
Forum: Futaba Radios Direct support forum
05-28-2020, 11:37 AM
Replies: 17
Views: 7,334
Posted By Suprawill1

Hi All, I am trying to set up for flaperons....

Hi All,
I am trying to set up for flaperons. I have set up by plugging the left aileron into ail ch 1 and the right into aux ch 6.
I then went into the T10J and activated the flaperons and then...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
02-15-2015, 09:03 PM
Replies: 1
Views: 845
Posted By Suprawill1

Well, for those who may be searching for the same...

Well, for those who may be searching for the same answer, this radio is not equipped for variable programmable mixing using channels 5 or 6 as slaves. Both channels are affected by the on/off...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
01-26-2015, 11:58 PM
Replies: 1
Views: 845
Posted By Suprawill1

Thrust Vectoring Mixing Setup

Hello All.
Hoping this hits those that are familiar with programmable mixing. (master/slave servos)
I've got the mixing properly set up in my Futaba radio Tx but when I power up, the vectoring...
Showing results 1 to 10 of 10


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.