RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Planecub
Showing results 1 to 18 of 18
Search took 0.02 seconds.
Forum: JR Radio & Spektrum Radios
07-24-2023, 07:55 AM
Replies: 2
Views: 579
Posted By Planecub

IC3 to IC5 adapter

I have 4 cell smart batteries with an ic3 plug and a 60 amp esc with a ic5 plug. I purchased an adaptor to fit between the battery and esc and while it works, it is too long. Is there an adaptor...
Forum: RC Flight Simulator Software
07-07-2023, 03:20 PM
Replies: 0
Views: 1,087
Posted By Planecub

Flaps stay down on Timber

I have RealFlight Evolution and am flying the E-flite Timber with slats. The problem is that I cannot change the angle of the flaps. They stay in the down position. I tried moving every switch,...
Forum: JR Radio & Spektrum Radios
06-17-2023, 07:29 PM
Replies: 1
Views: 560
Posted By Planecub

Telemetry sensor to tell if there is a complete circuit

I know about most of the sensors for telemetry for the Spektrum (voltage, rpm,temperature, etc, etc). Is there a sensor to determine if there is a complete electrical circuit (ie check if a bulb is...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
06-17-2023, 07:11 PM
Replies: 2
Views: 430
Posted By Planecub

Thank you RGBurrill, I received a Futaba spring...

Thank you RGBurrill, I received a Futaba spring loaded switch in the mail, bit the bullet, and soldered it in place of one of the two position switches. It works as intended and when I boot up the...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
06-16-2023, 04:31 AM
Replies: 2
Views: 430
Posted By Planecub

Replace two switches on Turnigy TGY-i6

I have a Turnigy TGY-16 transmitter that I would like to replace Switch A with a spring loaded switch and Switch D with a push button switch.
You have to have all of the switches in the up...
Forum: Marketplace
04-07-2023, 09:40 AM
Replies: 2
Views: 303
Posted By Planecub

Evolution 10cc gas engine

I have a slightly used Evolution 10CC gas engine for sale. It has very few flights on a Kadet Senior. Include is the spark box, rpm sensor, and muffler. The engine started easy and ran good. I am...
Forum: JR Radio & Spektrum Radios
09-06-2022, 04:27 AM
Replies: 2
Views: 656
Posted By Planecub

Thank you!

Thank you!
Forum: JR Radio & Spektrum Radios
09-05-2022, 01:54 PM
Replies: 2
Views: 656
Posted By Planecub

A couple of questions regarding the Spektrum ESC setup

I purchased a NX6 transmitter and a Timber Evolution. I like the "Smart" technology, so I am changing out my regular receivers and speed controllers with Spektrum Smart electronics. I want to do...
Forum: The Clubhouse
08-14-2022, 07:37 PM
Replies: 12
Views: 893
Posted By Planecub

Help with mild hand tremors

Today, I flew for the first time in a couple of years and noticed I have a a slight hand tremor. The airplane that I was flying really bounced around the sky and worried me. I was able to land it but...
Forum: Batteries & Chargers
10-18-2021, 07:55 PM
Replies: 6
Views: 2,616
Posted By Planecub

Thank you!

Thank you!
Forum: Batteries & Chargers
10-18-2021, 07:55 PM
Replies: 6
Views: 2,616
Posted By Planecub

Thanks

Thanks
Forum: Batteries & Chargers
10-18-2021, 05:32 AM
Replies: 6
Views: 2,616
Posted By Planecub

Thank you Andy. I was wondering if I got the...

Thank you Andy. I was wondering if I got the connectors too cheap. Funny you mention ProgressiveRC. I was looking about the internet and found a tool that they have to punch the connectors into...
Forum: Batteries & Chargers
10-17-2021, 08:09 PM
Replies: 6
Views: 2,616
Posted By Planecub

Another ec3 soldering question

I have searched the internet and youtube on how to solder wires to ec3 connectors and have a minor issue and a bigger issue. Btw, I am using 12 gauge silicone wire. One problem I have is that the ec3...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
05-05-2021, 12:55 PM
Replies: 0
Views: 382
Posted By Planecub

What sensors do companies use for rc engine tachometers

I would like to make my own tachometer using an Arduino and an optical senesor. I have looked at many examples of Arduino tachs, but either they use IR which you need a reflector on the propeller or...
Forum: JR Radio & Spektrum Radios
07-13-2020, 04:06 PM
Replies: 5
Views: 1,483
Posted By Planecub

Thank you Andy. So what is the size of the JST...

Thank you Andy. So what is the size of the JST connector (sh or zh) and and from what I assume, the plug that fits in the recepticle is the female plug.
Forum: JR Radio & Spektrum Radios
07-12-2020, 06:46 PM
Replies: 5
Views: 1,483
Posted By Planecub

Male or female connector to plug into the TM1000 or AR8010T question.

I'm pretty sure the connectors for the telemetry on the TM1000 and AR8019T are JST-ZH. I get confused by this, but what is the connector that plugs into the connector on the receiver. I am guessing...
Forum: JR Radio & Spektrum Radios
07-12-2020, 06:38 PM
Replies: 2
Views: 1,103
Posted By Planecub

Thank you!

Thank you!
Forum: Beginners
02-15-2020, 06:15 AM
Replies: 1
Views: 504
Posted By Planecub

Throttle stick question for ZLRC (The Beast)

I suppose this question really belongs in the quadcopter forum, but there is nobody there at the moment. I purchased a Syma X5c quadcopter at auction and flew it on Wednesday, It is a cheap quad...
Showing results 1 to 18 of 18


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.