RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: hunnerbunner
Showing results 1 to 14 of 14
Search took 0.71 seconds.
Forum: Speed - Electric
07-21-2005, 10:50 PM
Replies: 215
Views: 69,886
Posted By hunnerbunner

RE: SHOW UR BOATS PEOPLE

That Joker is sweet! I love a boat that is a little different from the crowd. I'll bet that thing looks awesome cruising around the pond! Did you build that yourself? I really like it.
Forum: Speed - Electric
07-20-2005, 08:24 PM
Replies: 31
Views: 7,134
Posted By hunnerbunner

RE: UPGRADING NIKKO TIGER

If you are using the stock nikko pack, that might be your problem, too. Those aa batteries just can't supply the amps to run the 540 motor under load. Try using the sub c pack to see if that makes...
Forum: Speed - Electric
07-15-2005, 04:26 PM
Replies: 5
Views: 1,422
Posted By hunnerbunner

RE: CEN AquaJet

That would be the, uh, 775. It came stock in the boat. Bigger than a 550, and needs at least 10 cells to run good.
Forum: Speed - Electric
07-15-2005, 11:09 AM
Replies: 5
Views: 1,422
Posted By hunnerbunner

RE: CEN AquaJet

Just stuck it there because the motor leads were so short. Since it has it's own cooling, I didn't even consider whether the motor cooling would affect it. It never got hot anyway.
Forum: Speed - Electric
07-15-2005, 12:01 AM
Replies: 5
Views: 1,422
Posted By hunnerbunner

CEN AquaJet

Thought I'd throw up some pics of the coolest boat I own. This thing is a 775 powered on 12 cells with flex shaft, carbon prop, and lots of cooling. Max speed recorded by GPS so far is 19.8 mph. ...
Forum: Speed - Electric
06-12-2005, 01:05 AM
Replies: 12
Views: 1,840
Posted By hunnerbunner

RE: Reef Racer with Super 400 Cobalt motor

Which octura prop is that?
Forum: Speed - Electric
05-26-2005, 12:45 PM
Replies: 21
Views: 1,827
Posted By hunnerbunner

RE: Micro Boat

Not saying that brushless won't work in a boat, just not as simple as throwing any motor in there. A rigger might be more receptive to a high-kv motor than a v-hull, but 8000kv is just too much for...
Forum: Speed - Electric
05-25-2005, 04:51 PM
Replies: 21
Views: 1,827
Posted By hunnerbunner

RE: Micro Boat

I thought about the gear reduction route for my brushless. Here are my experiences: The lower priced reduction units are offset, so they don't fit (had some, tried them, they don't fit). Got a...
Forum: RC Boats General Discussion
05-24-2005, 12:32 PM
Replies: 2
Views: 523
Posted By hunnerbunner

RE: Wanting to get into micro boating

For small, fast, and roostertail, check out the Gecko from MHZ. Just about right for the mamba, though 8000kv might be a bit much for any boat. 4800kv had mine skipping across the pond.
Forum: RC Boats General Discussion
05-24-2005, 12:26 PM
Replies: 5
Views: 1,889
Posted By hunnerbunner

RE: brushless reef racer

I put a park 400 brushless in mine last summer. It was definitely overkill. The boat handled just fine, no skittishness and no flips, and it sure was quick. Problem is, that hull will only go so...
Forum: Speed - Electric
03-08-2005, 08:03 PM
Replies: 1,056
Views: 108,980
Posted By hunnerbunner

RE: Aquacraft EP Hammer Thread

We just missed each other by a day, then. Decker lake is nasty, you should try swimming in it, tastes like a dog soaked in deisel [:'(]. I've seen the new park, but I fear upsetting the fishermen...
Forum: Speed - Electric
03-08-2005, 01:35 PM
Replies: 1,056
Views: 108,980
Posted By hunnerbunner

RE: Aquacraft EP Hammer Thread

Hey Bash_N_Thrash, I live in the SL valley and just wondering where you run your boats. The only place I know of is Decker lake, and I haven't seen any hammers there, just nitros. I'd like to run...
Forum: 1/16th, 1/18th, Mini & Micro RC Cars
11-03-2004, 07:11 PM
Replies: 10
Views: 2,256
Posted By hunnerbunner

RE: Leo-X Mini Monster/Venom Mini Giant motor

I stretched the drive shafts by cutting them in half, then epoxying them into an appropriately long piece of alum. tubing sized to fit them snugly. I have had no problems with them twisting out of...
Forum: 1/16th, 1/18th, Mini & Micro RC Cars
11-02-2004, 05:55 PM
Replies: 10
Views: 2,256
Posted By hunnerbunner

RE: Leo-X Mini Monster/Venom Mini Giant motor

The stock motor is a 7.2v 280. I have tried a 6v 280, graupner 280bb, and a 6v 370 (fireball spec). My fav for crawling was the stock motor with a 9t pinion till I stretched the wheelbase, now I...
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.