RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: johnf-4
Showing results 1 to 14 of 14
Search took 0.58 seconds.
Forum: JetCat Turbine Direct Support
05-30-2017, 03:35 PM
Replies: 7
Views: 1,085
Posted By johnf-4

Matt, two different ECU's. One is the original...

Matt, two different ECU's. One is the original from purchase and the other was new from rebuild.
GSM, have checked to see if touching engine body and both were clear. Have since found that screws...
Forum: JetCat Turbine Direct Support
05-28-2017, 09:16 PM
Replies: 7
Views: 1,085
Posted By johnf-4

Thanks Guy's. I have two P70's both with this...

Thanks Guy's. I have two P70's both with this problem, both with only 1hr 10min run time since major rebuilds at Jetcat factory so these were both new then.They have been in storage for four years...
Forum: JetCat Turbine Direct Support
05-25-2017, 04:53 PM
Replies: 7
Views: 1,085
Posted By johnf-4

Post P-70 code.

Can someone tell me what the letter 'E' flashing alternately with the temp when I go over 100.000 rpm on my P-70. It has version 6.10C ECU which is a new ECU.
This ECU has more functions than the...
Forum: RC Jets
11-23-2013, 04:23 PM
Replies: 292
Views: 47,253
Posted By johnf-4

HI Dion, F-4 is scratch built by myself. All...

HI Dion, F-4 is scratch built by myself. All fibreglass and composite. Fuel tanks built into the wings, Matrix extending nose wheel strut, working tail hook. Aileron setup as per the real F-4 with...
Forum: RC Jets
11-22-2013, 10:25 PM
Replies: 292
Views: 47,253
Posted By johnf-4

Ready for test flight

http://www.rcuniverse.com/forum/attachment.php?attachmentid=1941359http://www.rcuniverse.com/forum/attachment.php?attachmentid=1941360
Forum: RC Jets
02-25-2011, 01:19 AM
Replies: 7
Views: 2,103
Posted By johnf-4

RE: Nose wheel steering servo size

Thanks guy's, I now know where to go with this. Very much appreciated.
Kind Regards
John
Forum: RC Jets
02-23-2011, 12:54 AM
Replies: 7
Views: 2,103
Posted By johnf-4

Nose wheel steering servo size

Can I please have your thoughts on the size of servo (torque) that should be used on a 30lb - 35lb F-4 phantom jet.
Thank you
Forum: RC Jets
08-21-2009, 04:22 PM
Replies: 30
Views: 4,049
Posted By johnf-4

RE: (URGENT) Todd & Dreamworks

Take the time you need Todd. My thoughts are with you and take care.

John.
Forum: RC Jets
07-29-2009, 11:55 PM
Replies: 18
Views: 1,880
Posted By johnf-4

RE: Dreamworks Model Products - Another Complement

Excellent service over the last few years. Always very helpful on inquiries and fast as everyone else has already said. The online ordering service is excellent and very easy to use. First choice for...
Forum: Beginners
06-03-2009, 01:46 AM
Replies: 291
Views: 23,978
Posted By johnf-4

RE: RCU Roll call time..Where are you from?

Another down under. Marlborough New Zealand.
Forum: JetCat Turbine Direct Support
09-10-2008, 12:17 AM
Replies: 18
Views: 2,245
Posted By johnf-4

RE: Fasst Aux GSU issue

Ant, tpeppas3d,
I am running Futaba 12FGA with the FASST 6014 RX in my twin turbine F-4 Phantom. Two P70 ECUs with the throttles Y leaded together and the Aux's Y leaded...
Forum: JetCat Turbine Direct Support
09-08-2008, 06:43 PM
Replies: 18
Views: 2,245
Posted By johnf-4

RE: Fasst Aux GSU issue

Hi Ant,
Check that you have assigned the aux channel to the three positional switch in you radio and that the channels travel is set to 100%. Also check that the swich is set to the...
Forum: Futaba Radios Direct support forum
04-19-2008, 04:26 PM
Replies: 4
Views: 1,219
Posted By johnf-4

RE: R6014FS and GYA 352 dual axis gyro

Purchased GYA352 gyro on RC Universe about 10 months ago. US$150 plus freight.
Good Luck in finding one.
Forum: Futaba Radios Direct support forum
04-19-2008, 03:37 AM
Replies: 4
Views: 1,219
Posted By johnf-4

R6014FS and GYA 352 dual axis gyro

I am using a 12FGA 2.4Ghz radio on the program for 2 Ail and 1 Flap. Two servo's on each of the controls through an Duralite EVO powerbox. All works fine on this setup until I introduce my GYA352...
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.