RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 3
1
2
3
Search: Posts Made By: Aussie Maddog
Showing results 1 to 25 of 54
Search took 0.60 seconds.
Forum: Marketplace
04-14-2019, 02:29 AM
Replies: 0
Views: 469
Posted By Aussie Maddog

Super Tigre G2300 Engine NIB (Includes shipping to USA)

New Super Tigre G2300. Never run. 2 engines available, 2 sold. (Price is per engine)
Head has been drilled and tapped for a 10mm sparkplug as I was going to run electronic ignition.
An adapter has...
Forum: SuperTigre Engines Support
04-05-2019, 10:50 PM
Replies: 0
Views: 694
Posted By Aussie Maddog

New G2300 in "Marketplace"

I've listed 3 new G2300 in the rcu marketplace if anyone is interested. (Had 4, one sold)
I've tapped the head for a 10mm sparkplug and installed a magnet as I was going to fit ignition.
I've...
Forum: Marketplace
03-30-2019, 02:29 PM
Replies: 0
Views: 1,272
Posted By Aussie Maddog

Super Tigre G2300 NEW but modified

New Super Tigre G2300. Never run. 3 engines available. (Price is per engine)
Head has been drilled and tapped for a 10mm sparkplug as I was going to run electronic ignition.
An adapter has been...
Forum: Engine Conversions
04-25-2013, 11:40 PM
Replies: 7
Views: 1,240
Posted By Aussie Maddog

RE: prop hub for cy engine

Checkout the hub from the SPE 26 engine. From memory it has a tapered shaft. Not sure if it will fit though.
Forum: Gas Engines
02-26-2013, 10:20 AM
Replies: 18
Views: 1,321
Posted By Aussie Maddog

RE: Gas Conversion Magnet

I use a 4mm (Dia) X 5mm Rare Earth Magnet.
I drill a pilot hole through the hub then a 5/32 hole to correct depth.
Coat hole and magnet with CA glue and press into place. Between the jaws of a...
Forum: Engine Conversions
02-18-2013, 08:51 AM
Replies: 3
Views: 924
Posted By Aussie Maddog

RE: Different fuel pumps available

Interesting....Thankyou very much.
Forum: Glow Engines
01-30-2013, 02:04 AM
Replies: 24
Views: 6,155
Posted By Aussie Maddog

RE: Adding electronic ignition to a Saito 450R glow engine

Hello, Following this thread with interest.
Could I ask if you don't mind, did you check the firing of each individual sensor in relation to it's respective cylinder or just one cylinder then left...
Forum: Gas Engines
01-18-2013, 06:03 AM
Replies: 169
Views: 37,069
Posted By Aussie Maddog

RE: New Saito 4 Cycle Gas Engine, 3 Cyl FG-84

Please correct me if I'm wrong, but don't radial engines have non-symetrical spark firing?
Meaning a 3 cylinder engine does not fire every 120 degrees.
I believe it is to do with how the master...
Forum: Gas Engines
11-26-2011, 04:29 AM
Replies: 14
Views: 1,617
Posted By Aussie Maddog

RE: C S ignitions

Possibly this one? http://www.cncengines.com/
Forum: Gas Engines
11-11-2010, 10:19 AM
Replies: 11
Views: 1,220
Posted By Aussie Maddog

RE: recently bought a used spe 26

An extra 500 RPM can be had from a larger 11mm carb over the stock 9.5. Mine had a bad case casting that needed replacing.
Original ignitions were "melody" I believe. BCMA sold them with the RCEXL.
Forum: Gas Engines
07-19-2010, 02:45 AM
Replies: 109
Views: 13,397
Posted By Aussie Maddog

RE: RC Exl Ignition Users

I always machine my magnet hub 1 mm (40 thou) bigger in diameter than the Sensor securing hub and this gives me a nice close fit.

The ST G2300 below has the securing ring 1 mm under the standard...
Forum: Gas Engines
06-27-2010, 08:05 PM
Replies: 608
Views: 198,159
Posted By Aussie Maddog

RE: 15cc Gas RCGF engine information thread

I have adapted a "nitro" muffler to this engine. Not run it yet. Has a much bigger "chamber" but much smaller outlet. I may make up a dual pipe outlet like the one in the pic (made for a G2300).
Forum: Glow Engines
06-17-2010, 02:14 AM
Replies: 3
Views: 868
Posted By Aussie Maddog

RE: G90 exhaust mounting hole distance

47mm spacing.3mm bolts. Port width = 25mm X 8mm height.
Forum: Engine Conversions
06-16-2010, 02:55 PM
Replies: 60
Views: 12,366
Posted By Aussie Maddog

RE: ASP 52FS From Glow to Gas with RCExcel Ignition

This is a sensor mount I did for a Super Tigre 2300. It is secured by two M3 grub screws and can be rotated to set your timing.
If you have a 4mm diameter magnet, a 5/32 drill bit makes for a nice...
Forum: Gas Engines
04-28-2010, 04:22 AM
Replies: 21
Views: 2,681
Posted By Aussie Maddog

RE: MLD 28 won't keep running

Remove :Carb needles (high and low), Pump cover and membranes, Diaphragm cover and metering needle.
Blow out passages with carb cleaner and look down the carb throat to see the spray coming through...
Forum: Glow Engines
04-19-2010, 04:40 AM
Replies: 11
Views: 2,900
Posted By Aussie Maddog

RE: making my own glow engine,what materials for liner/piston

What about buying the piston/ring and making the sleeve. Pistons are relatively inexpensive and come with the piston pin and retainers ready for your rod.
For a novice, this maybe the way to go and...
Forum: Engine Conversions
03-25-2010, 10:38 PM
Replies: 8
Views: 1,390
Posted By Aussie Maddog

RE: Spark advance question

correct. Generally full advance is at around 4000 RPM.
Forum: Engine Conversions
03-25-2010, 10:31 PM
Replies: 8
Views: 1,390
Posted By Aussie Maddog

RE: Spark advance question

Yes 30 BTDC is the most. Start at 6-8 BTDC.
Forum: Engine Conversions
03-25-2010, 06:56 PM
Replies: 5
Views: 1,064
Posted By Aussie Maddog

RE: Gas to glow conversions

Walbro carb WT-499 is made for alcohol fuels. This may be your best option.
Forum: Giant Scale Aircraft - General
02-22-2010, 10:17 AM
Replies: 2
Views: 637
Posted By Aussie Maddog

RE: Where to get 9

Not exactly 9 inches but a reasonable price I thought .......
http://www.amr-rc.com/index.php?path=content&SUBSC=parts_wheels&SC=parts_wheels&page=parts_wheels
Forum: Gas Engines
02-03-2010, 07:11 AM
Replies: 12
Views: 2,278
Posted By Aussie Maddog

RE: hall sensor and magnet gap on SPE 40cc

The wrong side of the magnet could be facing the hall sensor. Hold the sensor upside-down and flick the magnet past it to see if you can get a spark.
Forum: Gas Engines
12-23-2009, 11:47 PM
Replies: 7
Views: 2,707
Posted By Aussie Maddog

RE: Walbro 694 vs 255C

The 12.7 is probably too big for a 26 (You may find transition issues) if not on a highly tuned engine like a Zenoah or other high end type.
And the 9.5 too small. Restricting RPM by 500 to 1000.
...
Forum: Gas Engines
11-30-2009, 04:42 AM
Replies: 6
Views: 2,296
Posted By Aussie Maddog

RE: SPE 26cc ignition timing 42 degrees?

A walbro with a 11mm venturi will help if you have the stock 9.5mm carb. I was getting 8300 on a SPC 16X8. It's chinese, the quality varies.
Forum: Gas Engines
06-16-2009, 11:34 PM
Replies: 42
Views: 4,289
Posted By Aussie Maddog

RE: What caused this?

Hello, This is exactly the spot where my SPE 26 crank broke. 
If I remember correctly, BCMA stated in their instructions that this could happen if an engine was mounted too solidly and my engine...
Forum: Engine Conversions
05-01-2009, 02:28 AM
Replies: 13
Views: 1,992
Posted By Aussie Maddog

RE: hobby city EI unit

The Rcexl is also available at hobbycity(Sensor sold separately), but I don't know which plug it's for. Hi-model sell a Rcexl unit (with sensor) as a spare part for the DL-50, CM-6 plug.
CH...
Showing results 1 to 25 of 54
 
Page 1 of 3
1
2
3


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.