RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: PigsOnTheWing
Showing results 1 to 13 of 13
Search took 0.60 seconds.
Forum: Brushed/Brushless motors, speed controls, gear drives
09-21-2005, 08:51 AM
Replies: 0
Views: 368
Posted By PigsOnTheWing

Recommeded brushless setup for GP Yak55?

Could somebody recommend a brushless motor/gearbox combo for a GP Yak 55? Or should I got with an outrunner? I have had a himax gearbox and an e-go? motor, never cou;ld get it set up right in my last...
Forum: Profile and Fun Flying Planes
09-21-2005, 07:30 AM
Replies: 96
Views: 9,825
Posted By PigsOnTheWing

RE: 47" OMP Edge 540 and Yak-54 ARF's

AFSalmon ; I sent you a PM back about AFP. Please LMK if that is Ok..
Thanks!!

edit-corrected spellin mistake
Forum: Profile and Fun Flying Planes
09-20-2005, 07:03 PM
Replies: 96
Views: 9,825
Posted By PigsOnTheWing

RE: 47" OMP Edge 540 and Yak-54 ARF's

Just got a chance to fly mine again. I LOVE IT !! It will fly fast and wild, but still slow down like a trainer for landing. All problems have been forgiven!! Plus, they are sending me the missing...
Forum: Profile and Fun Flying Planes
09-15-2005, 04:55 AM
Replies: 96
Views: 9,825
Posted By PigsOnTheWing

RE: 47" OMP Edge 540 and Yak-54 ARF's

That makes me feel GREAT. I sold my G2 simulator to buy this thing, I have always heard OMP was the shXt, I wish I had researched further. I guess since they didn't build it I can't completely blame...
Forum: Profile and Fun Flying Planes
09-12-2005, 08:38 PM
Replies: 96
Views: 9,825
Posted By PigsOnTheWing

RE: 47" OMP Edge 540 and Yak-54 ARF's

Thanks Mike.
Sent ya an email with the details.
I haven't flown it yet, but will VERY soon...
Forum: Profile and Fun Flying Planes
09-10-2005, 11:36 PM
Replies: 96
Views: 9,825
Posted By PigsOnTheWing

RE: 47" OMP Edge 540 and Yak-54 ARF's

I forgot to mention that the throttle servo plate was on the wrong side, and when I pushed the servo arm onto the aileron servo,the servo and mount broke loose and fell inside the wing!! I was not...
Forum: OMP - Ohio Model Products Support Forum
09-10-2005, 11:14 PM
Replies: 3
Views: 547
Posted By PigsOnTheWing

RE: 47" Yak balance question

I know this sounds dumb, but where is the main spar? Is it the main bead in the front of the wing(behind leading edge)? Thanks, I have to balance mine for in the morning.
Forum: Profile and Fun Flying Planes
09-10-2005, 11:10 PM
Replies: 96
Views: 9,825
Posted By PigsOnTheWing

RE: 47" OMP Edge 540 and Yak-54 ARF's

I built of of these over the last three nights. GREAT looking plane. Covering was flawless, no sanding on the wing opening. No control horns, clevises, or elevator joiner in my ARF kit. I used a...
Forum: HPI Monster Truck Forum
06-07-2005, 12:00 AM
Replies: 25
Views: 1,335
Posted By PigsOnTheWing

RE: Are the big rims and tires worth it?

Ntloser, I will give you another opinion. I have Big Joes on 40s on a Savage SS, and although I like them and they deifnately look cool, they are harder on the drivetrain than the stock setup. The...
Forum: Glow Engines
06-06-2005, 11:41 PM
Replies: 30
Views: 5,196
Posted By PigsOnTheWing

RE: New Saito .82 lost all compression!? Help!

Also, I have found that it helps to run the fuel out of a Saito 82 completely when quitting for the day (pull carb line) and then add after-run oil. I was having the same problems with mine, and have...
Forum: Glow Engines
06-06-2005, 09:44 AM
Replies: 3
Views: 575
Posted By PigsOnTheWing

RE: SAITO 82 repair ie pushrod part #'s?

Thanks so much, horizon's site can be irritating.

My Twist hit the ground@full throttle from 200 feet. My radio was beeping low battery, but I ignored it. Ouch!!!
Forum: Glow Engines
06-06-2005, 12:03 AM
Replies: 3
Views: 575
Posted By PigsOnTheWing

SAITO 82 repair ie pushrod part #'s?

Hi
Trying to repair a fairly new saito 82 but can't find parts on horizons(or any other) site? Was driven into the ground, I need pushrods and pushrod guides and seals. I also need an intake, but I...
Forum: OMP - Ohio Model Products Support Forum
05-22-2005, 10:47 PM
Replies: 6
Views: 917
Posted By PigsOnTheWing

RE: New OMP Website

Looks great guys!!!
A vast improvement, well done.
I look forward to owning one of your planes soon...
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.