RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: cdrc1
Showing results 1 to 10 of 10
Search took 0.65 seconds.
Forum: ARF or RTF
06-02-2023, 04:48 PM
Replies: 437
Views: 156,093
Posted By cdrc1

4-stroke engine install

Is it possible to install engine at 90 degrees instead of upside down?
Forum: Futaba Radios Direct support forum
12-25-2022, 01:04 AM
Replies: 1
Views: 532
Posted By cdrc1

Converting to 2.4 system

Bought new 7006SB receiver to convert one of my old 72Mhz planes over to Futaba 2.4Ghz 14SG system and the servos are chattering but they do work. Have it programmed for Mode A and FASSTest. Has S148...
Forum: Glow Engines
06-15-2019, 12:05 AM
Replies: 54,891
Views: 5,432,145
Posted By cdrc1

Still having same issue in the plane; had to turn...

Still having same issue in the plane; had to turn in the LSN so the fuel would stop pouring out prior to start; just spinning it. That is the tank being so high. So when I adjust the LSN in the plane...
Forum: Glow Engines
05-28-2019, 12:15 AM
Replies: 54,891
Views: 5,432,145
Posted By cdrc1

Was still having issues with transition; would...

Was still having issues with transition; would stall if you went straight to full. Took it back out of the plane and put it on the stand with the pump; had to turnout the low speed needle about 1 1/2...
Forum: Glow Engines
05-12-2019, 12:09 AM
Replies: 54,891
Views: 5,432,145
Posted By cdrc1

Thanks Jim; will try it.

Thanks Jim; will try it.
Forum: Glow Engines
05-10-2019, 10:05 PM
Replies: 54,891
Views: 5,432,145
Posted By cdrc1

Answers

Use Sullivan filters on all my planes and on field box fuel bottle. Have replaced the glow plug at least once and using a 4-stroke plug as recommended by Saito. The prop is a 14x7. Perry pump is a...
Forum: Glow Engines
05-09-2019, 11:07 PM
Replies: 54,891
Views: 5,432,145
Posted By cdrc1

The tank position is why I went with a pump. It...

The tank position is why I went with a pump. It is a perry pump and is a new set-up/new plane; engine was tuned and broke in on a test stand right side up. The on-board glow shuts off around 1/4...
Forum: Glow Engines
05-08-2019, 11:35 PM
Replies: 54,891
Views: 5,432,145
Posted By cdrc1

Saito 100 problem

Having an transition problem with my Saito 100. It is mounted upside down in a TF warbird; has a OB glow driver, and a pump. When transitioning from idle, the engine is sagging around mid range and...
Forum: Seaplanes
03-02-2008, 12:11 PM
Replies: 1
Views: 664
Posted By cdrc1

GP floats

A couple of years ago I built some GP floats for my .40 GP cub. I stored them in the attic and when I brought them down one of them had a small 3 inch crack in the side. I first thought it was from a...
Forum: Golden Age, Vintage & Antique RC
11-11-2007, 05:50 PM
Replies: 9
Views: 1,803
Posted By cdrc1

1985 Trainer

Looking for the name of my first plane built in 1985. It was a trainer and think it was a top flight kit. Was bought through tower. Had a engince size .40-.61 and was a semi-sym wing, with a large...
Showing results 1 to 10 of 10


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.