RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 3
1
2
3
Search: Posts Made By: Turd
Showing results 1 to 25 of 61
Search took 0.57 seconds.
Forum: Gas Engines
05-09-2011, 09:50 PM
Replies: 17
Views: 2,143
Posted By Turd

RE: Zenoah G20 Help??

sounds like its lean,check the spark plug it should be a light very brown if its lean, open the high speed needle about an 1/8 of a turn and check the plug after a few flights it should be medium...
Forum: Gas Engines
01-29-2011, 09:49 PM
Replies: 142
Views: 27,980
Posted By Turd

RE: Dle-20 Blew up....

This engine has a static timing of around 38 degrees before top dead center, the advanced timing is way too much as well, the number escapes me now. In my world that will break a crank and tear...
Forum: Gas Engines
11-20-2010, 01:07 PM
Replies: 25
Views: 5,724
Posted By Turd

RE: DLE 20 carb questoins

sounds like a a rich low setting, turn the low needle in a little bit at a time
Forum: Aeroworks Vendor Forum
03-02-2010, 09:45 AM
Replies: 16
Views: 3,685
Posted By Turd

RE: 35 cc Extra motor?

Ok I have to ask who`s got a DL or DA 50CC or maybe even an OS GT55 in one of these, Just wondering how it flys
Forum: Gas Engines
01-23-2010, 08:18 PM
Replies: 8
Views: 943
Posted By Turd

RE: carbon

Mister Clean also works well
Forum: RC Flight Simulator Software
11-07-2009, 08:05 AM
Replies: 3
Views: 837
Posted By Turd

RE: rf 4.5 to 5.0 problems

the number in the middle of your inter link is I2 not 0ne two or twelve
Forum: ARF or RTF
07-20-2009, 05:05 PM
Replies: 4
Views: 775
Posted By Turd

RE: what good bi-plane for 3d purposes could use a 26cc????

study this I am http://tech.flygsw.org/
Forum: Gas Engines
05-07-2009, 07:52 AM
Replies: 7
Views: 982
Posted By Turd

RE: need help finding a model posted here-??

try these guys http://www.rcguys.com/
Forum: Gas Engines
08-28-2008, 11:18 AM
Replies: 6,188
Views: 760,446
Posted By Turd

RE: DL-50 engine

Xoar 23x8 prop. So I revered back to my break in prop a Xoar 22x8 Sword looks like less load which will cause rich condition and burbling, mine runs best when its slightly hard to start, re...
Forum: RC Flight Simulator Software
07-17-2008, 03:46 PM
Replies: 1
Views: 2,085
Posted By Turd

RE: Realflight G3.5 won't install in XP...

right click and run or install as administrater
Forum: Gas Engines
07-13-2008, 11:15 PM
Replies: 6,188
Views: 760,446
Posted By Turd

RE: DL-50 engine

How many hours do you guys have on the DL 50 I have one with 9.5 hours and the ring rotates about .090 .100 I think its the ring or pin-32.01 oil since new and broke on 1.0 hours on the ground ,...
Forum: ARF or RTF
04-15-2008, 09:21 PM
Replies: 5
Views: 1,458
Posted By Turd

RE: Balsa Nova Instructions!!!?

If send me your address and I will photo copy my instruction booklet, you can pm me-- I also have a PDF file as well and it is just about the same as the booklet, your call
Forum: 3D Flying!
04-04-2008, 05:21 PM
Replies: 22
Views: 4,014
Posted By Turd

RE: what is best gyro for 3d

anyone use a gyro for 3D --------------no then i would not be 3D LLB
Forum: Kit Building
01-30-2008, 10:03 PM
Replies: 71
Views: 10,886
Posted By Turd

RE: Blasa Nova 1.20 - The Next Project

I have a Zenoah G20ei in an Balsa Nova A R F and i will tell you this thing is nice. Everything they say it is and more
Forum: Batteries & Chargers
01-27-2008, 01:53 AM
Replies: 4
Views: 265
Posted By Turd

RE: beware

are you sure its not the mafia
Forum: OMP - Ohio Model Products Support Forum
01-16-2008, 05:57 PM
Replies: 247
Views: 27,816
Posted By Turd

RE: Hybrid Edge

I some times put 3 degrees of right thrust in the firewall , washers seem to put strain on the motor mount lugs on a D? 50 cc engine
Forum: OMP - Ohio Model Products Support Forum
01-16-2008, 08:50 AM
Replies: 247
Views: 27,816
Posted By Turd

RE: Hybrid Edge

what about right thrust, i am at that point in the construction
Forum: Tips & Techniques
12-28-2007, 01:39 AM
Replies: 6
Views: 1,795
Posted By Turd

RE: Prop Flying off NO MORE

Using a four stroke ?
Forum: Gas Engines
12-23-2007, 10:58 PM
Replies: 43
Views: 4,356
Posted By Turd

RE: DL50 compression/starting

Pour a half a teaspoon of mixed gas into the carburetor, it will run for sure, the diaphragm {pump} is dry
Forum: Gas Engines
11-23-2007, 03:17 PM
Replies: 12
Views: 2,255
Posted By Turd

RE: Zenoah G20EI

use a dubro steering arm third hole out from the center
Forum: Futaba Radios Direct support forum
11-03-2007, 05:58 PM
Replies: 12
Views: 1,809
Posted By Turd

RE: FUTABA 2.4 GHZ transmitter with 7 or 8 channels?

Could you explain the difference between the six channel {R606FS} and the seven channel {R607FS} receivers they both have only 6 usable connections after the battery connection is installed
Forum: Profile and Fun Flying Planes
10-13-2007, 11:12 PM
Replies: 10
Views: 1,598
Posted By Turd

RE: Wildhare Extra 300 Profile

wow good idea ------ go for it what are your thoughts so far
Forum: Gas Engines
10-11-2007, 07:49 AM
Replies: 9
Views: 1,538
Posted By Turd

RE: Pictures of DL50 Engines

Who is mister ---- ""DONG""---- leave it alone guys LLB
Forum: Gas Engines
10-08-2007, 11:20 PM
Replies: 2,945
Views: 358,282
Posted By Turd

RE: Let's try again DL-50

does anyone know what the static timing spec is in degrees before top dead center
Forum: Gas Engines
09-07-2007, 11:38 AM
Replies: 5
Views: 1,270
Posted By Turd

RE: G20 spark plug gaps.

the maual says .018---.020 its hard to find in the manual
Showing results 1 to 25 of 61
 
Page 1 of 3
1
2
3


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.