RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: DKTimmy
Showing results 1 to 12 of 12
Search took 0.53 seconds.
Forum: RC On Road Nitro Cars
11-10-2006, 08:13 PM
Replies: 17
Views: 1,675
Posted By DKTimmy

RE: Headlights/taillights

How did you come up with the resistor values?
Forum: RC On Road Nitro Cars
10-29-2006, 07:43 PM
Replies: 17
Views: 1,675
Posted By DKTimmy

RE: Headlights/taillights

Sure, I'd like to see the placement pics. What will using different size resistors do to the light output.
Forum: RC On Road Nitro Cars
10-26-2006, 07:13 PM
Replies: 17
Views: 1,675
Posted By DKTimmy

RE: Headlights/taillights

Did you get your parts at radio shack?

If so what type of resistors did you get? They have so many that I am not sure which ones to get.

Thanks!
Forum: RC On Road Nitro Cars
10-21-2006, 06:26 PM
Replies: 5
Views: 897
Posted By DKTimmy

RE: Need a pic

it looked like there was a gap between the engine and cooling head and i can see the brass spacer or whatever it is. I just wanted to make sure that this is what it it suppose to look like. It is...
Forum: RC On Road Nitro Cars
10-19-2006, 08:10 PM
Replies: 5
Views: 897
Posted By DKTimmy

Need a pic

Could someone post a pic of their ntc3+ engine from underneath the cooling head. I took mine apart to check the internals, and want to make sure that I have gotten it put back together correctly. ...
Forum: RC Painting, Detailing & Bodies
08-08-2006, 07:42 PM
Replies: 2
Views: 535
Posted By DKTimmy

2nd Body attempt

Front Shot
Top Shot
Side Shot
Rear Shot

Might be a bit large for 56k.

Tell me what you think.
Forum: RC On Road Nitro Cars
08-06-2006, 06:48 PM
Replies: 1,165
Views: 177,698
Posted By DKTimmy

RE: Offical nitro tc3 thread

Thanks! Is there a limit on how much I can move the exhaust in? How far does it need to be away from the fuel line and the fuel tank?
Forum: RC On Road Nitro Cars
08-06-2006, 10:32 AM
Replies: 1,165
Views: 177,698
Posted By DKTimmy

RE: Offical nitro tc3 thread

Don't know if this is the right place to post this, but since it is the ntc3 forum and I have searched, I'll post away.

I went and got a BMW M3 hpi body for the ntc3 but am having an issue. ...
Forum: Batteries & Chargers
07-04-2006, 09:58 AM
Replies: 1
Views: 4,240
Posted By DKTimmy

9.6v charger for 7.2v packs

I was given a 9.6v charger for nicd and nimh batteries, and want to know if I can charge a 7.2v batt pack with it safely if I change the plug ends to match the packs. If so do I need to put a volt...
Forum: RC On Road Nitro Cars
06-09-2006, 08:14 PM
Replies: 1
Views: 260
Posted By DKTimmy

Ntc3+ and Stripping Screws

Maybe someone can help a newb out. I have a ntc3 with a little problem. I stripped the spur gears, so I started tearing the car down to replace them. As it turns out it seems as if every other...
Forum: RC On Road Nitro Cars
06-09-2005, 09:50 AM
Replies: 4
Views: 595
Posted By DKTimmy

RE: Breaking in a new Engine

Richen the high speed or the low speed needle? I haven't been able to get a temp gun yet and if i put a dab of water on the cooling head, it seldom seems to sizzle away.

Would it be wise to...
Forum: RC On Road Nitro Cars
06-08-2005, 08:22 PM
Replies: 4
Views: 595
Posted By DKTimmy

Breaking in a new Engine

Recently got a nitro tc3+ and have put around 10 - 12 tanks of 20% fuel through it yet can never get it to run right. I followed the directions with the kit, have reset all the needles and...
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.