RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: alvinsmith75
Showing results 1 to 14 of 14
Search took 0.53 seconds.
Forum: Gas Engines
08-25-2014, 03:34 PM
Replies: 1,709
Views: 339,133
Posted By alvinsmith75

LOL Revolver 70 is in the back of my mind too.

LOL Revolver 70 is in the back of my mind too.
Forum: Gas Engines
08-25-2014, 03:21 PM
Replies: 1,709
Views: 339,133
Posted By alvinsmith75

Thanks! I just saw your post after I researched...

Thanks! I just saw your post after I researched and made my previous post.
Forum: Gas Engines
08-25-2014, 03:20 PM
Replies: 1,709
Views: 339,133
Posted By alvinsmith75

Thanks Steve. Decisions decisions lol. Looking...

Thanks Steve. Decisions decisions lol. Looking at Hangar 9 I'm not sure why the P47 is so much more expensive than the P51 considering the P51 comes with spinner and manual retracts and the P47...
Forum: Gas Engines
08-25-2014, 01:26 PM
Replies: 1,709
Views: 339,133
Posted By alvinsmith75

No warbird experience at all. Not scared either...

No warbird experience at all. Not scared either lol. If you look at my previous post in this thread I built a 60 sized super chipmunk with a DLE 20. The super chipmunk has similar specs as far as...
Forum: Gas Engines
08-25-2014, 12:45 PM
Replies: 1,709
Views: 339,133
Posted By alvinsmith75

Thinking about getting a warbird for my DLE 20...

Thinking about getting a warbird for my DLE 20 RA. Any suggestions? I figure any 60 sized plane will do. Just wondering what "the community" has or suggest. I don't have a preference really. If...
Forum: Gas Engines
08-02-2014, 06:59 PM
Replies: 1,709
Views: 339,133
Posted By alvinsmith75

You don't want the Phoenix plane from Tower...

You don't want the Phoenix plane from Tower Hobbies....................................................Unless you are aerobastic! LMAO

NOTES FROM OUR TECH DEPARTMENT

This is the Radio...
Forum: Gas Engines
08-01-2014, 05:35 PM
Replies: 1,709
Views: 339,133
Posted By alvinsmith75

A friend of mine has a DLE 20RA in this ...

A friend of mine has a DLE 20RA in this
http://www.horizonhobby.com/products/sbach-342-60-arf-HAN4215#t1
According to the specs it's 2 pounds lighter than the Phoenix version. This plane flies...
Forum: Gas Engines
07-24-2014, 12:59 PM
Replies: 1,709
Views: 339,133
Posted By alvinsmith75

As you can see I have done what you are asking. ...

As you can see I have done what you are asking. The difference is my plane is a kit which is usually much stronger than an ARF. In your situation I would maybe epoxy another 1/8th in thicker...
Forum: Gas Engines
01-07-2014, 09:44 AM
Replies: 1,709
Views: 339,133
Posted By alvinsmith75

I have ordered the 17x6 and will try it. I also...

I have ordered the 17x6 and will try it. I also wanted to report that I stuck a tach on my dle35 which is rated at 8500 rpm and it only turns 7000 rpm so I see the rated rpm is definitely not a...
Forum: Gas Engines
01-04-2014, 04:10 PM
Replies: 1,709
Views: 339,133
Posted By alvinsmith75

I plan on flying it tomorrow. I will check...

I plan on flying it tomorrow. I will check ground clearance then. As far as a three blade goes I think I read somewhere where a 15x7 three blade is recommended for that engine.
Forum: Gas Engines
01-04-2014, 12:32 PM
Replies: 1,709
Views: 339,133
Posted By alvinsmith75

Thanks for all of the advice guys. Not sure if I...

Thanks for all of the advice guys. Not sure if I have enough ground clearance to go to a 17" prop, but I will check. If not would the 16x6 show any noticeable difference in torque over the 16x8? I...
Forum: Gas Engines
01-03-2014, 09:19 AM
Replies: 1,709
Views: 339,133
Posted By alvinsmith75

http://www.rcuniverse.com/forum/attachment.php?att...

http://www.rcuniverse.com/forum/attachment.php?attachmentid=1953869http://www.rcuniverse.com/forum/attachment.php?attachmentid=1953870http://www.rcuniverse.com/forum/attachment.php?attachmentid=195387...
Forum: Gas Engines
10-07-2013, 04:48 AM
Replies: 1,709
Views: 339,133
Posted By alvinsmith75

Thanks for all the replies guys. After your...

Thanks for all the replies guys. After your comments and further research I believe it will work. I am also considering moving the elevator and rudder servos to the tail of the plane like they are...
Forum: Gas Engines
10-05-2013, 03:48 AM
Replies: 1,709
Views: 339,133
Posted By alvinsmith75

Haven't owned a Super Chipmunk in over 20 years...

Haven't owned a Super Chipmunk in over 20 years but it was always my favorite plane. I am about to build another one. The Carl Goldberg .60 size kit. I was originally going to install the...
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.