RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 2
1
2
Search: Posts Made By: G.W.K.
Showing results 1 to 25 of 31
Search took 0.56 seconds.
Forum: Car Nitro & Gas Engines
07-31-2012, 10:58 AM
Replies: 3
Views: 881
Posted By G.W.K.

RE: help with hex screw on sh. 18 engine

Don´t know the size exactly, but it´s definitve metric. Maybe two mm?
Forum: Car Nitro & Gas Engines
07-30-2012, 12:32 PM
Replies: 9
Views: 9,144
Posted By G.W.K.

RE: OS 28xz or LRP zr.32

Ah, i see, ok got ya a bargain there, nice.

As you found out yourself, the OS is a racing engine. The LRP engines are bashing engines, loads of power, easy to tune, but not that economic with...
Forum: Car Nitro & Gas Engines
07-29-2012, 10:01 AM
Replies: 9
Views: 9,144
Posted By G.W.K.

RE: OS 28xz or LRP zr.32

Second that. About 200 Bucks for the LRP and 330 Bucks for the 28XZ isn´t exactly the same price range...The Picco .28 might be an alternative.
Forum: Car Nitro & Gas Engines
07-15-2012, 06:19 AM
Replies: 4
Views: 1,083
Posted By G.W.K.

RE: .28 picco 9port turbo

I think, he added one shim for the use of 30% nitro. The engine is set up for the use of 25% Nitro from factory. I would recommend 25% either.

The break-in time of those Picco engines is far...
Forum: Car Nitro & Gas Engines
07-06-2012, 11:42 AM
Replies: 1
Views: 1,773
Posted By G.W.K.

RE: Different models of Picco 26MAX JL REDDOT?

Did some research and even mailed OFNA. This is in fact the most recent version of the engine. The photo from ofnawarehouse shows actually the crank of a different engine (Picco .12 JL).

There...
Forum: Car Nitro & Gas Engines
07-03-2012, 07:24 AM
Replies: 1
Views: 1,773
Posted By G.W.K.

Different models of Picco 26MAX JL REDDOT?

Hi,

i just got my Picco .26MAX JL RED DOT from Towerhobbies and had to look inside and was a bit, umm, disappointed.

...
Forum: RC Monster Trucks
09-15-2009, 05:30 PM
Replies: 9
Views: 3,667
Posted By G.W.K.

RE: New Schumacher Manic Info

The engines aren´t fully broken-in yet...
Forum: RC Nitro Stadium Trucks
06-12-2009, 06:02 AM
Replies: 21,657
Views: 1,514,312
Posted By G.W.K.

RE: Official HPI MT2 Thread

Thanks for the replies!
I have the non-pullstart flywheel( <font size="-1">A926) </font>from HPI and it&acute;s for the engines with OS crankshafts(like the HPI 18ss engine), so doesn&acute;t fit. I...
Forum: RC Nitro Stadium Trucks
06-11-2009, 05:22 PM
Replies: 21,657
Views: 1,514,312
Posted By G.W.K.

RE: Official HPI MT2 Thread

Hi,
have a little prob with my new built 18ss+. I wanna install a OS18tz non-pullstart, but i can´t figure out yet, which parts i really need. I thought i got the right ones, but i didn´t...
Forum: RC Monster Trucks
06-11-2006, 04:24 PM
Replies: 734
Views: 53,057
Posted By G.W.K.

RE: Official Gen/Nemisis Thread

OOUUCH!![X(]
Forum: RC Monster Trucks
05-30-2006, 06:48 PM
Replies: 2,328
Views: 257,601
Posted By G.W.K.

RE: Tower Hobbies Nitro TOWER Terror MT .25 RTR

Here in Germany this thing is called "track-sau(track-pig)".
I´ve seen a vid and it is f***ing fast and a wheely-machine as it´s best.
It hasn´t much features, but where isn´t much, there...
Forum: RC Monster Trucks
02-09-2006, 06:40 PM
Replies: 32
Views: 2,434
Posted By G.W.K.

RE: What is everyone's position on the new Savage X??

Around 440$ at TH.[8D]
Forum: Traxxas Monster Truck forum
02-05-2006, 07:29 AM
Replies: 8
Views: 2,051
Posted By G.W.K.

RE: Revo Sirio .23 - what pipe to use?

If you go with the RB pipe, you ´ll need the RB-header too.
Forum: Traxxas Monster Truck forum
01-30-2006, 03:49 PM
Replies: 68
Views: 29,183
Posted By G.W.K.

RE: Ofna Picco .26 Max vs Sirio .23 (for revo)!

Maybe..., but then, you need the BB-Installation-Kit, header and a suitable pipe.
Probably a new cb and clutch too.
And then, as you see, your "price advantage" is gone.:eek:
Forum: RC Monster Trucks
01-29-2006, 08:57 AM
Replies: 6
Views: 560
Posted By G.W.K.

RE: is there RPm a- arms for savage??

Nope. [8D]
Forum: Traxxas Monster Truck forum
01-08-2006, 06:57 PM
Replies: 6
Views: 608
Posted By G.W.K.

RE: Revo Tranny Lube

I sprayed some silicon-oil in it.
Forum: Traxxas Monster Truck forum
01-08-2006, 01:48 PM
Replies: 3
Views: 527
Posted By G.W.K.

RE: removing opti drive

Get a F.O.C. and it works.
Forum: Traxxas Monster Truck forum
01-08-2006, 01:47 PM
Replies: 3
Views: 465
Posted By G.W.K.

RE: New to revo need some help.

Some alu-diff-housings aren´t bad too...
Forum: Traxxas Monster Truck forum
01-08-2006, 12:48 PM
Replies: 6
Views: 796
Posted By G.W.K.

RE: HPI .25 or Sirio Revo??

You need an EZ-Start backplate for that.
Why don´t you get a Picco 26 max, or a RB TM323? They´re much easier to install.
And you can use the EZ-Start as well.
Forum: Traxxas Monster Truck forum
01-08-2006, 10:52 AM
Replies: 6
Views: 796
Posted By G.W.K.

RE: HPI .25 or Sirio Revo??

That´s the Forward Only Conversion which eleminates the reverse gearing.
It makes the tranny more durable.
There is another prob too. Maybe the crankcase of the HPI 25 is to long and can touch...
Forum: Traxxas Monster Truck forum
01-08-2006, 09:18 AM
Replies: 6
Views: 796
Posted By G.W.K.

RE: HPI .25 or Sirio Revo??

With the BB-Kit, i think they will fit both in the Revo.
You should get Alu-Diff-Housings+ shim-kit, the FOC and a longer gear-ratio to prevent wheelies.
A prob could be to find a proper...
Forum: Traxxas Monster Truck forum
01-07-2006, 02:31 PM
Replies: 12
Views: 909
Posted By G.W.K.

RE: RB 323 PROBLEMS

Uhm, go back to stock-settings and try again.
Forum: RC Monster Trucks
01-06-2006, 07:11 PM
Replies: 90
Views: 6,045
Posted By G.W.K.

RE: REVO or LST

The only question is, do ya wanna big-size truck or a mid-size truck...:D
I think, it isn´t really fair to compare both trucks with each other. :eek:
I own a Revo myself with a Sirio.23.
Maybe...
Forum: Traxxas Monster Truck forum
01-05-2006, 04:41 PM
Replies: 68
Views: 29,183
Posted By G.W.K.

RE: Ofna Picco .26 Max vs Sirio .23 (for revo)!

Hi,
i´ve a Sirio in my Revo too.
http://i7.photobucket.com/albums/y291/tiger1e/SIMG2287.jpg
http://i7.photobucket.com/albums/y291/tiger1e/SIMG2339.jpg

IMHO, everything bigger than a .23...
Forum: Traxxas Monster Truck forum
01-01-2006, 10:02 AM
Replies: 12
Views: 909
Posted By G.W.K.

RE: RB 323 PROBLEMS

Seems like the LSN is to lean. I had the same prob this week with my Sirio.23.
Try richening up the LSN 1/4 to 1/2 of a turn(turn counterclockwise).
Showing results 1 to 25 of 31
 
Page 1 of 2
1
2


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.