RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: samp
Showing results 1 to 15 of 15
Search took 0.51 seconds.
Forum: JR Radio & Spektrum Radios
10-23-2017, 03:59 AM
Replies: 2
Views: 1,921
Posted By samp

DX9/AR9020 system issue?

After several years of trouble free flying with my DX9 I had a problem with the DX9/AR9020 installation in an EDF airplane this past Friday. The airplane had 3 previous flights and extensive bench...
Forum: AMA Discussions
06-11-2011, 03:32 AM
Replies: 178
Views: 19,229
Posted By samp

RE: Lawsuit filed against AMA

I find this whole scenario disgusting. People have lost touch with common sense. I hope, if this goes to trial, that enough modelers and spectators are called by the AMA to bury the attorney who...
Forum: O.S. Engines Support
03-16-2010, 12:10 PM
Replies: 1
Views: 482
Posted By samp

Surpass parts interchangeability

Bax,

This is a follow-up to my question about availability of a replacement cylinder head for a pre-2000 FS-91 Surpass. It appears the 91 Surpass II head is similar, with the obvious external...
Forum: O.S. Engines Support
03-15-2010, 12:19 PM
Replies: 2
Views: 1,818
Posted By samp

RE: FS-91 Surpass Cylinder Head

Thank you for the reply Bill. A "Wanted" ad is posted here on RCU.
Forum: RC Warbirds and Warplanes
03-13-2010, 08:30 PM
Replies: 1,430
Views: 345,138
Posted By samp

RE: ESM T-28

Keep it going Ty. What will you use for power?
Forum: O.S. Engines Support
03-13-2010, 03:04 PM
Replies: 2
Views: 1,818
Posted By samp

FS-91 Surpass Cylinder Head

Anybody aware of a source for a cylinder head for an FS-91 Surpass Engine? The part numbers were OSMG5134/45904100 for the head and OSMG5230/4590400 for the head with valve assembly. OS says the...
Forum: RC Warbirds and Warplanes
09-14-2009, 04:53 PM
Replies: 10
Views: 938
Posted By samp

RE: Warbirds over Easley SC

Hello Kevin,
The Meister 109 in winter white is powered by a ZDZ Super 80. The builder/flyer is Forest Morris.
The Firetower club is a really great group of people.
Enjoyed meeting you-will...
Forum: Gas Engines
07-11-2009, 05:28 PM
Replies: 23
Views: 1,902
Posted By samp

RE: Evolution 26 getting Hot

I agree with Pe. A damaged front bearing would certainly cause the overheating symptoms you describe. A technique I recently learned for removing sleeves is to carefully heat the cylinder ( from...
Forum: MVVS Support
12-22-2007, 04:23 PM
Replies: 2
Views: 1,201
Posted By samp

RE: 35CC How much shaft runout is normal?

Thank you Dar,

Exactly the information I was looking for. Excellent engine.

Sam
Forum: MVVS Support
12-22-2007, 03:14 PM
Replies: 2
Views: 1,201
Posted By samp

35CC How much shaft runout is normal?

My very good running 35CC recently had prop/spinner contact with terra firma. The dial indicator shows some runout at the end of the prop shaft. Can anyone tell me how much is normal?

Thank...
Forum: MVVS Support
11-02-2006, 09:04 AM
Replies: 2
Views: 847
Posted By samp

RE: 35cc loose carb

Pe,

Thank you for the reply. Yes, the carb installation is like the large OS, ST, and MOKI. The engine is smooth and powerful and appears to be very well made.

Sam
Forum: Gas Engines
11-02-2006, 08:56 AM
Replies: 6
Views: 1,563
Posted By samp

RE: Evolution 35 GT

Pat,

That sounds like a good and permanent solution. What prop did you end up running on your 35?

Sam
Forum: Gas Engines
11-01-2006, 12:11 PM
Replies: 6
Views: 1,563
Posted By samp

RE: Evolution 35 GT

Pat,

Just found your post today after posting a similar message on the MVVS site yesterday. My 35cc/2.15 CI has the same problem. Prop is balanced to a gnat's whisker as is the spinner. ...
Forum: MVVS Support
10-31-2006, 07:27 PM
Replies: 2
Views: 847
Posted By samp

35cc loose carb

The Walbro carb gets loose on my 35cc gas engine after several flights. Each time I clean the set screws and apply thread locker and allow time for it to set overnight before flying again. ...
Forum: RC Scale Aircraft
08-22-2006, 03:07 PM
Replies: 429
Views: 128,537
Posted By samp

RE: T-28 True 1/5 Scale

Johnny,

My first encounter with full scale heavy metal was in a T-28 "A" model over 40 years ago. I would certainly be interested in plans, cowl, canopy, and either templates or laser cut ribs...
Showing results 1 to 15 of 15


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.