RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: nsherman
Showing results 1 to 19 of 19
Search took 0.67 seconds.
Forum: Futaba Radios Direct support forum
05-28-2002, 05:06 PM
Replies: 1
Views: 735
Posted By nsherman

Futaba R122JE Rx

I have recently purchased a Futaba 2PHKA Tx and R122JE Rx. The guy at the local hobby shop told me that I needed to cut the antenna down to make it work with the 2PHKA radio. Something about...
Forum: RC Boats General Discussion
05-22-2002, 08:47 PM
Replies: 3
Views: 711
Posted By nsherman

fuel question?

I use Blue Thunder 30% fuel in my K&B 3.5 Outboard.
Forum: RC Fuels
03-21-2002, 01:44 AM
Replies: 0
Views: 982
Posted By nsherman

What fuel ???

I am new to nitro engines and could use some help. First, I have a K&B 3.5 Outboard engine on a Prather Lap Cat I. When I bought it, the previous owner said they ran 15%. My local hobby shop says...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
03-14-2002, 05:59 AM
Replies: 2
Views: 796
Posted By nsherman

Battery Voltage???

It is going to have a Magnum GPA 40 on it. About 3 1/2 feet long. The battery pack i had in mind was a 1200 mah nmdh pack.
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
03-14-2002, 05:29 AM
Replies: 2
Views: 796
Posted By nsherman

Battery Voltage???

Help... I am building an airboat and will be using 3 servos. 1 for the throttle and 2 for the steering. Will a 4.8v Rx battery be enough? Or do I need a larger battery.

:confused:

Thanks...
Forum: Glow Engines
03-11-2002, 04:27 AM
Replies: 1
Views: 699
Posted By nsherman

Magnum 40...

Sorry, it is a Magnum GPA 40
Forum: Glow Engines
03-11-2002, 04:25 AM
Replies: 1
Views: 699
Posted By nsherman

Magnum 40

Anybody have any experience with this engine? (ie: what fuel to run, prop size?) Any opinions on this engine?
Forum: Glow Engines
02-20-2002, 05:55 AM
Replies: 10
Views: 1,251
Posted By nsherman

Cleaning engines?

What do you use to lube the internal parts after a crock-pot cleaning? Any certain oil?

Thanks,
Nick
Forum: Glow Engines
02-20-2002, 05:54 AM
Replies: 2
Views: 642
Posted By nsherman

After cleaning...

What do you use to lube the internal parts after a crock-pot cleaning? Any certain oil?

Thanks,
Nick
Forum: Glow Engines
02-07-2002, 10:58 PM
Replies: 10
Views: 841
Posted By nsherman

Sleeve

Thanks for all of the replies. Ed you description is pretty much right on. Thanks for being so detailed.

You guys have been a great help.

Nick
Forum: Glow Engines
02-07-2002, 06:06 PM
Replies: 10
Views: 841
Posted By nsherman

Sleeve

When I got the engine it was in peices. I had to get gaskets and screws for it and am putting it back together. I have another one here but didn't want to take it apart to compare.
Forum: Glow Engines
02-07-2002, 03:10 PM
Replies: 10
Views: 841
Posted By nsherman

Piston Sleeve

There are no marks on the cylinder or head to match it to. There are 5 holes in the sleeve tough. If I knew which one is the exhaust, I could line that up?

Nick
Forum: Glow Engines
02-07-2002, 02:05 AM
Replies: 10
Views: 841
Posted By nsherman

Piston Sleave

Can anyone tell me the direction the piston sleave goes into the cylender? This is my first nitro engine, I had the head off and the sleave out and want to get it back in correctly. There is a...
Forum: Glow Engines
01-22-2002, 07:55 PM
Replies: 0
Views: 644
Posted By nsherman

K&B 3.5 Outboard Drive Cable

Can someone tell me how to lube the drive cable on a K&B 3.5 outboard? Can it be done externally, or does the motor have to be taken apart?

I have looked at the K&B website but it does not give...
Forum: Batteries & Chargers
01-11-2002, 03:11 PM
Replies: 9
Views: 1,549
Posted By nsherman

Voltage

Ok, I pulled a battery out and and ran a short across the empty slot and it worked. The response time on the servos doesn't seem to be any slower than before. Looks like the 4.8V will be fine.
...
Forum: Batteries & Chargers
01-11-2002, 06:54 AM
Replies: 9
Views: 1,549
Posted By nsherman

Voltage

Just tried it and when I take 1 battery out nothing works. But that could be because there is nothing closing the circuit. Not sure.

Nick
Forum: Batteries & Chargers
01-11-2002, 06:32 AM
Replies: 9
Views: 1,549
Posted By nsherman

Voltage

It is a 4 AA (dry) cell pack. Each AA (currently Energizer) battery is 1.5V for a total of 6V. The pack I was looking to buy is a NiMH 4.8V and I thought I better find out if it work before I buy...
Forum: Batteries & Chargers
01-11-2002, 05:18 AM
Replies: 9
Views: 1,549
Posted By nsherman

Another battery question...

Thanks for the information. I do have one more question on the topic. The current dry cell setup says 6V on it. Does the NiMH also have to be 6V also or can it be 4.8V?

Thanks again for your...
Forum: Batteries & Chargers
01-10-2002, 05:23 AM
Replies: 9
Views: 1,549
Posted By nsherman

Newbie Battery Question

I am a new RC'er and have a battery question. My current Rec. battery pack is 4 AA dry cell setup (yuk). I am looking at a NiMH 4.8 (Hobbico HydriMax 4.8V 1200mAh Square). What does the 1200mAh...
Showing results 1 to 19 of 19


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.