RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Search
Today's Posts
Mark Forums Read
Vendor Directory
Notices
 
Page 1 of 11
1
2
3
Last »
Search: Posts Made By: edgeguy
Showing results 1 to 25 of 256
Search took 0.88 seconds.
Forum: E-Flite Helicopters
02-10-2011, 08:22 PM
Replies: 5
Views: 721
Posted By edgeguy

RE: MSR forward flight

You are correct. When flying forward at high speeds you will need to also add a little left diagonal stick. If you want to fly backwards fast you will need to apply a little right and rear diagonal...
Forum: E-Flite Helicopters
02-10-2011, 07:36 PM
Replies: 5
Views: 721
Posted By edgeguy

RE: MSR forward flight

This is caused by lift dissymmetry. All helicopters have this. The MSR and the SR 120 suffer from this big time. You can mix this out if you have a computer transmitter if not you will have to apply...
Forum: E-Flite Helicopters
01-05-2011, 12:27 PM
Replies: 20
Views: 5,138
Posted By edgeguy

RE: Should I buy the MCX or MCX2?

You should be fine with the MSR. With it swashplate set on the short pins and the radio in trainer mode it is very docile and easy to fly. But move the smashplate to the long pins and take the TX out...
Forum: E-Flite Helicopters
01-05-2011, 10:36 AM
Replies: 20
Views: 5,138
Posted By edgeguy

RE: Should I buy the MCX or MCX2?

Get the MCX2. It has better motors and batteries plus it looks a whole lot better. It is a blast to fly. If you are real good with the Air Hog the MCX or MCX2 may be a little boring after a day or...
Forum: YS Engines Support
08-23-2009, 12:57 PM
Replies: 1
Views: 536
Posted By edgeguy

RE: Ys 110FZ Low end too rich

We need a little more info. Fuel, plug etc. Your settings are way too lean. Clean the regulator to start with.
Forum: 3D Flying!
12-31-2005, 03:48 PM
Replies: 1,869
Views: 233,655
Posted By edgeguy

RE: AeroWorks Edge 540T 46-60?

cmircman, the point I am making is Aeroworks knew about the weak fuse a year ago and did not do a thing about it until now. From what I can see the fuse on the old and new planes are the same or very...
Forum: 3D Flying!
12-29-2005, 09:50 PM
Replies: 1,869
Views: 233,655
Posted By edgeguy

RE: AeroWorks Edge 540T 46-60?

Isnt this funny!!!!!!!!!! I had the earlier version of this plane and only had 10 flight on it and the fuse broke in half while taxiing exactly where the new fuse doublers for this plane go. I was...
Forum: YS Engines Support
06-05-2005, 10:12 PM
Replies: 2
Views: 365
Posted By edgeguy

RE: mejzlik prop on 120?

Ronk1

I have aalways run Mejzlik props on my YS 120 FZ they will work and work great. 16X8 is the ticket. Enjoy! Bob
Forum: 3D Electric Flying!
04-18-2005, 10:58 AM
Replies: 10
Views: 966
Posted By edgeguy

RE: Brushless for my ultimate.

rdmonster, I have the e-flite brushless 400 4200kv on my ultimate and it fits without any trimming of the foam. It has unlimited vertical. It has soo much power that if you go full throttle on a...
Forum: Glow Engines
03-06-2005, 10:05 PM
Replies: 8
Views: 1,002
Posted By edgeguy

RE: Home brew smoke on YS .63?

Here is a plumbing schematic that I have been using for years and it works great! Just make sure to turn the smoke off as soon as the smoke oil runs out or your YS will run lean. Print the schematic...
Forum: Glow Engines
02-14-2005, 05:04 PM
Replies: 16
Views: 5,026
Posted By edgeguy

RE: Thunder Tiger Pro 36 . Any good?

Thank you all for the great replies. I am very eager to get the plane done and see what the Thunder Tiger Pro 36 will do. I have some 10X6 props and some 9X6 and 9X7 props to try. What do you all...
Forum: Glow Engines
02-13-2005, 11:15 PM
Replies: 16
Views: 5,026
Posted By edgeguy

Thunder Tiger Pro 36 . Any good?

I just purchased a Thunder Tiger Pro 36 for my new combat plane. Are Thunder Tiger engines any good? Anything special I should know about them? Anything special for break in?

Thanks for the...
Forum: Glow Engines
02-13-2005, 11:08 PM
Replies: 5
Views: 1,867
Posted By edgeguy

RE: YS 120 Muffler help

Jim, the OS muffler will not work on th YS. The threads in the head are different. Buy the muffler from Performance Specialties. It works great and looks good too. Too bad it is soo expensive! Bob
Forum: Glow Engines
02-04-2005, 05:13 PM
Replies: 2
Views: 481
Posted By edgeguy

RE: Need YS stock engine needle settings

diablokid, good starting point for all of the above YS engines is 1.5 turns out for high speed and low speed and flush with the regulator screw. Then fine tune from there. Remember the low speed is...
Forum: Glow Engines
02-03-2005, 12:03 AM
Replies: 3
Views: 2,868
Posted By edgeguy

RE: Smoke tank size & battery size for Ultimate 120?

seanychen, your right the DZ won't work with this set up. I hope they have improved the Sullivan Skywriter. A couple of friends of mine purchased these when they first came out and they leaked like...
Forum: Glow Engines
02-02-2005, 07:40 PM
Replies: 3
Views: 2,868
Posted By edgeguy

RE: Smoke tank size & battery size for Ultimate 120?

seanychen, since you have a YS you can use the YS pressure system to push the smoke oil. I have been using this set up for years and this is the best smoke system I have ever tried. This system is...
Forum: ARF or RTF
01-26-2005, 11:00 PM
Replies: 1,368
Views: 189,139
Posted By edgeguy

RE: Matt Chapman cap 580 .40 size

I got to maiden a friends 580 yesterday. It has a YS 63S with an APC 13X6 prop and 30% nitro. It is a great flying plane! The YS hauled it around with authority. The recommended low rate aileron was...
Forum: ARF or RTF
01-25-2005, 12:46 AM
Replies: 12
Views: 1,416
Posted By edgeguy

RE: smoke system in the funtanna 90

DiabloKid, here is the plumbing drawing. I purchased this kit a few years ago. It was from Carle Goldberg models. Dave Patrick is who designed the system. I don't think the kit is available anymore...
Forum: ARF or RTF
01-23-2005, 08:56 PM
Replies: 837
Views: 85,057
Posted By edgeguy

RE: New Miss America P-51... I saw one today

My previous post was wrong.

Sorry my error these were 14X7 3 blade and 14X9 3 blade. Sorry for the error. Bob
Forum: ARF or RTF
01-23-2005, 03:23 PM
Replies: 837
Views: 85,057
Posted By edgeguy

RE: New Miss America P-51... I saw one today

I had a H9 Mustang with a YS 91FZ and a MA 14X7 three blade and the 91 would turn the MA14X7 at 9400 rpm on 30%. this is at 6000 feet elevation. I would think the YS 110 FZ would need the MA 14X9 3...
Forum: ARF or RTF
01-21-2005, 12:08 PM
Replies: 65
Views: 5,336
Posted By edgeguy

RE: Let's See Those ARF'S!

Twistr, it does not have smoke but it may get smoke in the future. There is planty of room to mount a smoke system in the fuse. With a YS you can use the YS pressure system to push the smoke oil. You...
Forum: Glow Engines
01-20-2005, 10:26 PM
Replies: 61
Views: 6,756
Posted By edgeguy

RE: Saito or YS engines.

Red baron Mike, I don't think anyone was denigrating anyone else here at all. If you are refering to my comment of " In my opinion if you don't like YS you need medical treatment" did you notice the...
Forum: Glow Engines
01-20-2005, 12:13 AM
Replies: 61
Views: 6,756
Posted By edgeguy

RE: Saito or YS engines.

Between me and a good friend we have 2 YS 120FZ, 1 YS 140sport, 1 YS 140DZ, 3 YS 110, 1 YS 63FZ, 1 YS 63S and 2 YS 91FZ engines all have run flawless right out of the box. Every one of these engines...
Forum: ARF or RTF
01-19-2005, 10:17 PM
Replies: 53
Views: 6,779
Posted By edgeguy

RE: Aeroworks Edge 540 40 size fuse broke in half while taxiing!

Chris, sorry but this plane is taking a dirt nap in the local landfill.
Forum: ARF or RTF
01-19-2005, 10:14 PM
Replies: 12
Views: 1,416
Posted By edgeguy

RE: smoke system in the funtanna 90

If you are using a YS for power you can push the smoke oil with the YS engine pressure. All you need is a smoke tank, a 2 ounce pressure tank, 3 check valves some fuel line for gas and some silicon...
Showing results 1 to 25 of 256
 
Page 1 of 11
1
2
3
Last »


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.