RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: danemotty
Showing results 1 to 14 of 14
Search took 0.50 seconds.
Forum: 3D Flying!
05-04-2009, 06:43 AM
Replies: 13
Views: 2,081
Posted By danemotty

RE: MOJO 60 Saito 100 vibration

Could you please send me a pic of this installation thanks dane
Forum: 3D Flying!
05-02-2009, 02:22 PM
Replies: 13
Views: 2,081
Posted By danemotty

RE: MOJO 60 Saito 100 vibration

could you please post the link to the Pro Bros forum i tried to locate and could not thanks for your help
Forum: 3D Flying!
05-02-2009, 12:49 PM
Replies: 13
Views: 2,081
Posted By danemotty

RE: MOJO 60 Saito 100 vibration

what do you think about the apc 16x4w or 15x4w props ?
Forum: 3D Flying!
05-02-2009, 11:44 AM
Replies: 13
Views: 2,081
Posted By danemotty

RE: MOJO 60 Saito 100 vibration

For more information also: Once motor was mounted and run the muffler came loose only after about 5 minutes of running that gives you an idea of how much vibration i am having...the muffler was...
Forum: 3D Flying!
05-02-2009, 11:40 AM
Replies: 13
Views: 2,081
Posted By danemotty

RE: MOJO 60 Saito 100 vibration

also i tried flying it to see the difference off of the ground and it vibrated so much it would almost make the wings flutter at 80-100 power....mainly the left wing and the motor is mounted on the...
Forum: 3D Flying!
05-02-2009, 11:37 AM
Replies: 13
Views: 2,081
Posted By danemotty

RE: MOJO 60 Saito 100 vibration

Yes the prop was balanced and had flown it with the SK 70. also the engine that i purchased had at least a few gallons of fuel through it... Has anyone seen major vibration with this setup? and it...
Forum: 3D Flying!
05-02-2009, 08:05 AM
Replies: 13
Views: 2,081
Posted By danemotty

MOJO 60 Saito 100 vibration

Need some suggestions: I bought a used MOJO 60 in excellent shape with SK 70 installed. Pulled the SK off and installed a Saito 100 for the power with a 14x4W propeller. The 100 installed in the same...
Forum: RC Helicopter Beginners Forum
02-25-2008, 12:11 PM
Replies: 9
Views: 3,085
Posted By danemotty

RE: TREX 450 main blade tracking

Correction from my last couple of post my blades are fiberglass originals. Thanks for the help so far i appreciate it very much
Forum: RC Helicopter Beginners Forum
02-24-2008, 06:26 PM
Replies: 9
Views: 3,085
Posted By danemotty

RE: TREX 450 main blade tracking

wood original blades, no difference when i adjust the grips several turns even
Forum: RC Helicopter Beginners Forum
02-24-2008, 04:09 PM
Replies: 9
Views: 3,085
Posted By danemotty

RE: TREX 450 main blade tracking

yes i replaced the main shaft (assembly)
Forum: RC Helicopter Beginners Forum
02-24-2008, 07:42 AM
Replies: 9
Views: 3,085
Posted By danemotty

TREX 450 main blade tracking

I have a TREX 450 XL, last time i flew had a small crash, decided to replace the main rotor assembly and feathering spindle everything else looked ok but i cannot get the blades to track, tried...
Forum: RC 1/8th Scale Buggies
01-21-2007, 10:25 PM
Replies: 85
Views: 7,514
Posted By danemotty

RE: OPS MOTORS!

Could anyone help me out with a rough tuning procedure for a ops .45??

I have one in a boat, it idles ok but the high end does not reach top rpm and i dont have a lot of smoke coming out so it...
Forum: Speed - RC Nitro Boats
01-16-2007, 04:03 PM
Replies: 16
Views: 1,201
Posted By danemotty

RE: STARTER DIFFICULTIES!!

what do you do with the belt after startup, does it just stay around the output shaft????
Forum: Speed - RC Nitro Boats
01-14-2007, 06:55 PM
Replies: 16
Views: 1,201
Posted By danemotty

RE: STARTER DIFFICULTIES!!

I also have a new boat that is used and was wondering how to use the belt to start the engine any help, compression seems very strong, how do you get the belt or where do you put the belt to try to...
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.