RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Cliff_B
Showing results 1 to 17 of 17
Search took 0.42 seconds.
Forum: Electric Pattern Aircraft
04-14-2017, 08:10 AM
Replies: 5
Views: 2,764
Posted By Cliff_B

Cantilizer incendence ?

I am working to trim my first plane with a cantilizer, trying to figure out where the incendence should be for the cantilizer, should it be the same as the wing or set it to the stab or somewhere in...
Forum: Electric Pattern Aircraft
03-23-2017, 07:28 AM
Replies: 77
Views: 39,467
Posted By Cliff_B

The wing tube is 23 5/8" long, I have never seen...

The wing tube is 23 5/8" long, I have never seen nor heard of a failure with BJ's wings. I have snapped mine numerous times and while some like the 25 degree ail snap, it's to fast and difficult to...
Forum: Electric Pattern Aircraft
03-12-2017, 08:04 AM
Replies: 77
Views: 39,467
Posted By Cliff_B

I used the AJ style mount on the front by adding...

I used the AJ style mount on the front by adding 1/8 lite ply ring added on inside of nose, this works well if you use tapered type screw and counter sink a bit, use 3/16 spacers between the plywood...
Forum: Electric Pattern Aircraft
03-03-2017, 06:49 PM
Replies: 77
Views: 39,467
Posted By Cliff_B

I agree with all the suggestions, I just wanted...

I agree with all the suggestions, I just wanted everyone to know you needed to be careful and make some adjustments if you plan to stay with the BJ latch. I obviously had too much internal air...
Forum: Electric Pattern Aircraft
03-02-2017, 08:15 PM
Replies: 77
Views: 39,467
Posted By Cliff_B

Put the first flight on my Element today, light...

Put the first flight on my Element today, light cross wind so wasn't able to tell a lot, I set the CG on wing bolts and that seemed correct, I made it about 3 min before the canopy blew off, I was...
Forum: Electric Pattern Aircraft
08-22-2014, 02:49 PM
Replies: 665
Views: 172,588
Posted By Cliff_B

Finally got my Nuance repaired and back in tHe...

Finally got my Nuance repaired and back in tHe air with a new OS 1100 ESV ( thanks Dave for the help setting it up) dialed in 1/2 round positive incendence set the cg at 160 mm, and it is a...
Forum: Electric Pattern Aircraft
08-12-2014, 06:02 PM
Replies: 665
Views: 172,588
Posted By Cliff_B

Thanks for the reply Bill, I also noted a squeal...

Thanks for the reply Bill, I also noted a squeal prior to failure but failed to recognize it as a issue. With the stab at 0 deg the wing is only at .2 deg positive . But to get the stab to 0 the...
Forum: Electric Pattern Aircraft
08-12-2014, 03:21 PM
Replies: 15
Views: 2,537
Posted By Cliff_B

Those are the steps I used Hans, I just did it...

Those are the steps I used Hans, I just did it while setting every thing up, after watching the video Joe made I didn't make any mistakes, I didn't have the motor hooked up but that is not required...
Forum: Electric Pattern Aircraft
08-12-2014, 03:17 PM
Replies: 15
Views: 2,537
Posted By Cliff_B

HaHa that's just what I need, at least I would...

HaHa that's just what I need, at least I would get another shot at programming , but I don't think another is in my future.
Forum: Electric Pattern Aircraft
08-12-2014, 03:13 PM
Replies: 15
Views: 2,537
Posted By Cliff_B

Nice video Joe, I didn't see that before I sat...

Nice video Joe, I didn't see that before I sat down to program, but all the steps I followed the same with the exception of having the motor hooked to it to hear the beeping, everything else was the...
Forum: Electric Pattern Aircraft
08-12-2014, 09:13 AM
Replies: 15
Views: 2,537
Posted By Cliff_B

YGE fire / Programing

Would like to know if I made a mistake or just had a faulty ESC, YGE 90HV, Plettenberg Advance 30-10.
this is the values I used with the card to program the esc.

Timing : 24 deg
Brake : ...
Forum: Electric Pattern Aircraft
08-11-2014, 07:41 PM
Replies: 665
Views: 172,588
Posted By Cliff_B

Thanks for the encouragement, I have followed...

Thanks for the encouragement, I have followed this thread and that's why I bought one.
I do have adjusters on it, I didn't like the idea of having to add them if needed, I will do as you suggest...
Forum: Electric Pattern Aircraft
08-10-2014, 02:29 PM
Replies: 665
Views: 172,588
Posted By Cliff_B

Flew my nuance yesterday, equipment a was pletty...

Flew my nuance yesterday, equipment a was pletty advance, YGE. With JR servos, plane would go strait up but required right rudder to maintain the line. Also had pull to canopy on down lines, hook...
Forum: Electric Pattern Aircraft
03-26-2014, 05:47 PM
Replies: 520
Views: 145,790
Posted By Cliff_B

Thanks Dave, not sure which plane I'm going to...

Thanks Dave, not sure which plane I'm going to end up with, leaning towards the Nuance without the dfts wings and the mount just looks to easy to pass, could build my own but not building the plane...
Forum: Electric Pattern Aircraft
03-25-2014, 06:43 PM
Replies: 520
Views: 145,790
Posted By Cliff_B

Hey snowman, sent you a pm, interested in getting...

Hey snowman, sent you a pm, interested in getting one of these G10 mounts you had cut. Pm me please and we can set it up thanks Cliff
Forum: Electric Pattern Aircraft
09-05-2013, 01:16 PM
Replies: 1,677
Views: 405,145
Posted By Cliff_B

Finally, the Vanquish in question is mine I had...

Finally, the Vanquish in question is mine I had trouble getting in to post, elevators are at 0 deg, throw,s and tracking have been rechecked and are the same. Plane does not drop a wing while...
Forum: T-Rex heli
10-31-2006, 11:05 AM
Replies: 9
Views: 816
Posted By Cliff_B

RE: I need some Help with a T-rex 450, Everyone...

Hey Turbo, Check out heliproz, they have a good deal on the SE that includes everything but the raido transmitter and rcv'r. The SE comes with a good motor and speed controler. you will also need to...
Showing results 1 to 17 of 17


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.