RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: CPPROMAN
Showing results 1 to 14 of 14
Search took 0.40 seconds.
Forum: T-Rex heli
12-22-2006, 09:27 PM
Replies: 0
Views: 387
Posted By CPPROMAN

HeliDirect HDX 450 SE

Has anybody on this forum built the HDX 450 from HeliDirect..
I have just purchased the SE version, some thoughts on the build would be Great
Forum: E-Flite Helicopters
10-30-2006, 08:09 PM
Replies: 98
Views: 38,968
Posted By CPPROMAN

RE: Setup for Spectrum DX6 and Blade CP Pro

Make sure throttle trim is at zero.. Not Just the throttle.. Page 21 CPPro manual
[sm=punching.gif]
Forum: E-Flite Helicopters
10-27-2006, 11:39 AM
Replies: 98
Views: 38,968
Posted By CPPROMAN

RE: Setup for Spectrum DX6 and Blade CP Pro

In addition to TallPauls tell tale flashing diode story.. I found out that even a certain amount of trim (Throttle) caused the RED
Forum: E-Flite Helicopters
10-23-2006, 03:10 PM
Replies: 8
Views: 1,989
Posted By CPPROMAN

RE: Real Flight G3 and Spektrum DX6

Has anyone tried the Spektrum DX6 radio with the Realflight G3 training system as yet?
Forum: E-Flite Helicopters
10-22-2006, 06:04 PM
Replies: 0
Views: 246
Posted By CPPROMAN

Li Po Batteries

Has anyone purchased Li Po batteries from this company..
Dollar value does not seem bad [X(]


http://www.amondotech.com/index.asp?PageAction=Custom&ID=72
Forum: E-Flite Helicopters
10-22-2006, 01:37 PM
Replies: 15
Views: 1,159
Posted By CPPROMAN

RE: CP Pro - Newbie Learns Lesson (Hard Way)

I was experiencing the same.. I added a bigger piece of fuel tubing the same as Heli-Harry, I also added a piece of fuel tubing to slightly lenghten the tail stand
Forum: E-Flite Helicopters
10-20-2006, 12:37 PM
Replies: 8
Views: 1,989
Posted By CPPROMAN

Real Flight G3 and Spektrum DX6

Has anyone tried the Spektrum DX6 radio with the Realflight G3 training system as yet?[/size]
Forum: E-Flite Helicopters
10-19-2006, 07:07 PM
Replies: 98
Views: 38,968
Posted By CPPROMAN

RE: Setup for Spectrum DX6 and Blade CP Pro

I am still using the stock servos, no mechanical adjustments have been made to the heli at all.. I dont have a pitch gauge, but it looked like the OEM setup with the DX was giving me full positive...
Forum: E-Flite Helicopters
10-19-2006, 06:28 PM
Replies: 98
Views: 38,968
Posted By CPPROMAN

RE: Setup for Spectrum DX6 and Blade CP Pro

My Chopper has nver seen the repair hangar as yeT :)

I tried the setup as you posted Heli H.. but with my ship the head speed was low compared to stock transmitter therefore I felt the ship a...
Forum: E-Flite Helicopters
10-19-2006, 05:16 PM
Replies: 98
Views: 38,968
Posted By CPPROMAN

RE: Setup for Spectrum DX6 and Blade CP Pro

Spektrum DX6 CP Pro setup direct from the manufacturer

First off you need the Spektrum DX6 radio system or if you already have one for other e-helis and e-planes you need to purchase an...
Forum: E-Flite Helicopters
10-13-2006, 09:10 PM
Replies: 98
Views: 38,968
Posted By CPPROMAN

RE: Setup for Spectrum DX6 and Blade CP Pro

Take a look at the manual that came witht the Spektrum, under Heli. The servo locations are not the same as the stock reciever, you may find the you have the servos in the wrong location.. I followed...
Forum: E-Flite Helicopters
10-12-2006, 04:53 PM
Replies: 98
Views: 38,968
Posted By CPPROMAN

RE: Setup for Spectrum DX6 and Blade CP Pro

Thanks Guys.. Bought a Spektrum today, just wished it came with charged up batteries so I could fly it . I'll let you know if it works with my bird.. Also called Horizon hobbies they are also...
Forum: E-Flite Helicopters
10-12-2006, 04:50 PM
Replies: 3
Views: 517
Posted By CPPROMAN

RE: Blade CP Pro - Futaba TX6As

Thanks Guys...
Looked around a lot last night on the www for prices etc..

In the end I chose the Spektrum, I quess it is an upgrade to the CP Pro line anyways.. My thoughts were the 80...
Forum: E-Flite Helicopters
10-11-2006, 02:36 PM
Replies: 3
Views: 517
Posted By CPPROMAN

Blade CP Pro - Futaba TX6As

Help...

I would like to use my Futaba TX6As with my Blade CP Pro. Can anyone help me with the setup parameters?
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.