RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 10
1
2
3
Last »
Search: Posts Made By: edberg
Showing results 1 to 25 of 249
Search took 0.45 seconds.
Forum: 1/16th, 1/18th, Mini & Micro RC Cars
06-19-2010, 09:23 PM
Replies: 2
Views: 416
Posted By edberg

RE: CVD's won't reach after Vendetta PBS Conversion

That worked, I screwed in the bottom ball until it stopped. So I take it you use the upper ball to adjust camber?

Thanks!
Forum: 1/16th, 1/18th, Mini & Micro RC Cars
06-19-2010, 04:11 PM
Replies: 2
Views: 416
Posted By edberg

CVD's won't reach after Vendetta PBS Conversion

I just installed the PBS conversion on my buggy and now the CVD's don't reach, is there a way to adjust them?

http://i267.photobucket.com/albums/ii315/edberggonzalez/CIMG0098.jpg
Forum: 1/16th, 1/18th, Mini & Micro RC Cars
06-14-2010, 11:59 PM
Replies: 2
Views: 1,739
Posted By edberg

Duratrax Vendetta Buggy Tire Selection

What kind of wheels/tires are available for the Vendetta Buggy? I'm trying to put together a list of stock or near stock-sized wheels and tires that fit the buggy. I just bought a set of stock Half8...
Forum: 1/16th, 1/18th, Mini & Micro RC Cars
06-07-2010, 08:24 PM
Replies: 8
Views: 1,084
Posted By edberg

RE: Duratrax Vendetta BL install

I ended up shaving the shaft down with sandpaper, now it fits. Thanks for the help!
Forum: 1/16th, 1/18th, Mini & Micro RC Cars
06-07-2010, 02:17 AM
Replies: 8
Views: 1,084
Posted By edberg

RE: Duratrax Vendetta BL install

One last thing, after notching the chassis it fits fine but did you also notch the cover? The only way it seems that it will go on is if I drill a hole straight through, but that might let dirt in.
Forum: 1/16th, 1/18th, Mini & Micro RC Cars
06-07-2010, 01:54 AM
Replies: 8
Views: 1,084
Posted By edberg

RE: Duratrax Vendetta BL install

Did you use the 19t insert? There seems to be alot more drivetrain noise when I roll it around the floor.
Forum: 1/16th, 1/18th, Mini & Micro RC Cars
06-06-2010, 01:42 PM
Replies: 8
Views: 1,084
Posted By edberg

RE: Duratrax Vendetta BL install

I took the motor apart and noticed a shim in the back, I moved it to the front and reassembled it. I can't really tell if this helps or not since I can't get the motor on the motor mount.
Forum: 1/16th, 1/18th, Mini & Micro RC Cars
06-06-2010, 04:24 AM
Replies: 8
Views: 1,084
Posted By edberg

Duratrax Vendetta BL install

I'm having trouble installing an Ammo 28-35-3900kv motor in my vendetta buggy. Do I need a custom motor mount to fit this? The screws are too big and even if I drill out the holes the bottom one just...
Forum: RC 1/8th Scale Buggies
03-06-2009, 10:28 AM
Replies: 21
Views: 2,069
Posted By edberg

RE: Engine for an Ultra MBX Pro

How do you know when they actually go bad? Do they start to slip a bit or just not engage at all? Oh, and feel free to throw in any break-in tips out there if you have any.
Forum: RC 1/8th Scale Buggies
03-06-2009, 09:33 AM
Replies: 21
Views: 2,069
Posted By edberg

RE: Engine for an Ultra MBX Pro

Ready to go! :D

http://i267.photobucket.com/albums/ii315/edberggonzalez/e7c74bed.jpg

Just wondering, it should be ok to break the engine in on those integy clutch shoes right? Was planning...
Forum: RC 1/8th Scale Buggies
02-27-2009, 04:30 PM
Replies: 21
Views: 2,069
Posted By edberg

RE: Engine for an Ultra MBX Pro

And a 15$ mistake, integy clutch set is useless, the flywheel rubs against the engine. Found a little bit of money and I'm gonna go to the LHS to get some real gear.
Forum: RC 1/8th Scale Buggies
02-23-2009, 12:18 PM
Replies: 21
Views: 2,069
Posted By edberg

RE: Engine for an Ultra MBX Pro

Argh, the more I try to wind it the more the coil deforms. 20$ mistake [:@]
Forum: RC 1/8th Scale Buggies
02-22-2009, 09:52 PM
Replies: 21
Views: 2,069
Posted By edberg

RE: Engine for an Ultra MBX Pro

Oops.

http://i267.photobucket.com/albums/ii315/edberggonzalez/CIMG2506.jpg

Curiosity screwed me over [&:]

I'll get it back in eventually.
Forum: RC 1/8th Scale Buggies
02-21-2009, 05:38 PM
Replies: 21
Views: 2,069
Posted By edberg

RE: Engine for an Ultra MBX Pro

It's here. :D

http://i267.photobucket.com/albums/ii315/edberggonzalez/CIMG2504.jpg

I also ordered that Inegy clutch set for the flywheel and brass collet, I'll pick up some clutch...
Forum: RC 1/8th Scale Buggies
02-18-2009, 11:44 PM
Replies: 21
Views: 2,069
Posted By edberg

RE: Engine for an Ultra MBX Pro

Or better yet, will the flywheel/brass collet of that be any good? Because a flywheel/collet from ofna costs more then the entire integy set. I could always dump the clutch shoes/springs and only...
Forum: RC 1/8th Scale Buggies
02-18-2009, 08:22 PM
Replies: 21
Views: 2,069
Posted By edberg

RE: Engine for an Ultra MBX Pro

Any other cheap flywheel/clutch sets?
Forum: RC 1/8th Scale Buggies
02-18-2009, 03:43 PM
Replies: 21
Views: 2,069
Posted By edberg

RE: Engine for an Ultra MBX Pro

Well I bought the 21, hope it was the right decision. One last question, will the following flywheel/clutch set work for this engine?

...
Forum: RC 1/8th Scale Buggies
02-17-2009, 10:50 AM
Replies: 21
Views: 2,069
Posted By edberg

RE: Engine for an Ultra MBX Pro

What difference in speed should I expect? If it's something small like 5mph I'd might as well go for the extra torque.

Also some have a purple or gray head (7port?), the one I'm planning on...
Forum: RC 1/8th Scale Buggies
02-17-2009, 12:46 AM
Replies: 21
Views: 2,069
Posted By edberg

Engine for an Ultra MBX Pro

Which engine would work better in this buggy? A Force 28 or Hyper 21? The stock engine is a Force 26. I don't know if gear ratios are important, but it has a 51t Spur gear, same one used in the LX...
Forum: RC 1/8th Scale Buggies
02-16-2009, 06:01 PM
Replies: 13
Views: 1,858
Posted By edberg

RE: Newbie help, OFNA Ultra MBX Pro

Anyone? I'm afraid this deal won't be up for much longer. D:
Forum: RC 1/8th Scale Buggies
02-16-2009, 04:33 AM
Replies: 13
Views: 1,858
Posted By edberg

RE: Newbie help, OFNA Ultra MBX Pro

I've found a great deal on an Ofna force .28, I think it is the one used on the Ultra LX One. How will it do in this buggy and how does it compare to the stock force .26?
Forum: RC 1/8th Scale Buggies
02-07-2009, 05:10 PM
Replies: 13
Views: 1,858
Posted By edberg

RE: Newbie help, OFNA Ultra MBX Pro

Someone at the track is offering me a traxxas 3.3 engine from a jato, i think its a .20, how will it preform? Should i get it?

Please reply quickly, as i am at the track and posting from my...
Forum: RC 1/8th Scale Buggies
01-28-2009, 08:18 PM
Replies: 13
Views: 1,858
Posted By edberg

RE: Newbie help, OFNA Ultra MBX Pro

Just bid on the 7port, will the stock muffler work with it?
Forum: RC 1/8th Scale Buggies
01-27-2009, 01:47 PM
Replies: 13
Views: 1,858
Posted By edberg

RE: Newbie help, OFNA Ultra MBX Pro

Whats the difference between these two?

...
Forum: RC 1/8th Scale Buggies
01-27-2009, 10:38 AM
Replies: 13
Views: 1,858
Posted By edberg

RE: Newbie help, OFNA Ultra MBX Pro

Only cheap engines I could find, of the ones you listed at least.

...
Showing results 1 to 25 of 249
 
Page 1 of 10
1
2
3
Last »


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.