RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: hackinboy
Showing results 1 to 21 of 21
Search took 0.41 seconds.
Forum: Engine Conversions
02-22-2012, 12:35 PM
Replies: 21
Views: 4,669
Posted By hackinboy

RE: av8tor1977

Just had the pleasure of opening a box of engines I purchased from AV8TOR. He did a pair of 44cc ECHOs for a twin project Im working on, amazing machining on the polished prop hubs and the timing...
Forum: Engine Conversions
04-01-2009, 01:20 PM
Replies: 42
Views: 5,240
Posted By hackinboy

RE: Super Tiger 3250 on gas

Mike,
You can buy a rare earth magnet at Radio Shack and they work great. Just hook up your ignition and pass the magnet under the pick-up, it will only fire with one side of the magnet. Make...
Forum: Engine Conversions
02-27-2009, 11:55 AM
Replies: 653
Views: 104,589
Posted By hackinboy

RE: another darn ryobi post (ryobi performance modification, analysis and comparison)

Combatpilot,
After changing to a larger carb in test 6 did you notice a difference in the idle? Each time I've tried to put a larger carb on a stock Ryobi my idle was terrible and the rpm needed...
Forum: Engine Conversions
01-23-2009, 03:36 PM
Replies: 11
Views: 1,592
Posted By hackinboy

RE: Weedie motor

Flathead,
I buy them from Hobbycity.com for a couple bucks each...............mark
Forum: Engine Conversions
12-17-2008, 04:09 PM
Replies: 9
Views: 1,396
Posted By hackinboy

RE: Small motorcycle minibike engines?

Flathead,
I have a Lawnboy engine too. I believe you are looking at somewhere around 140-145CCs (cant remember exactly). Ive cut one down and chopped off the shaft for the mower blade. Havent...
Forum: Engine Conversions
12-17-2008, 10:34 AM
Replies: 380
Views: 56,675
Posted By hackinboy

RE: Echo BME twin

Sent you a PM a few days ago. Does your friend still have the cases?................m
Forum: Engine Conversions
10-20-2008, 11:54 AM
Replies: 5
Views: 962
Posted By hackinboy

RE: old craftsman 2.0

Should be about 32.8 CCs
1 CI = 16.387 CCs
Forum: Gas Engines
09-12-2008, 02:23 PM
Replies: 880
Views: 122,381
Posted By hackinboy

RE: New SV Gassers

I assumed you had the super stearman and i have the PT-17. I think you are right about the altitude. I havent messed with the timing to see if i can get more but will one of these days
Forum: Gas Engines
09-12-2008, 11:44 AM
Replies: 880
Views: 122,381
Posted By hackinboy

RE: New SV Gassers

I agree with Lotech that the SV will easily fly a 10 pound plane. I have one in the Stearman PT-17 at 14.5 pounds and it flies fine. I dont get near the RPMs out of it as him though. With a 15X8...
Forum: Engine Conversions
04-16-2008, 09:00 AM
Replies: 2
Views: 954
Posted By hackinboy

RE: 28 & 31 cc Ryobi

Cutarug,
I may be wrong but im pretty sure the 28 and 31cc engines have different cooling fins at the spark plug. The 28s have either one or two cooling fins that are much smaller than the others....
Forum: Engine Conversions
04-14-2008, 03:14 PM
Replies: 76
Views: 7,667
Posted By hackinboy

RE: weedeater/chainsaw 39cc for free, where to start?

The second part is correct. Unless you are using something different, the carb you have has a fuel pump in it. I''ll need to go back through the thread and make sure you are using a normal set up...
Forum: Engine Conversions
04-14-2008, 02:32 PM
Replies: 76
Views: 7,667
Posted By hackinboy

RE: weedeater/chainsaw 39cc for free, where to start?

I''m not sure I follow what you did but, you do need to have the tank vented so that line needs to stay open. You do need to plug the hose that goes into the carb where (i assume) your primer bulb...
Forum: Engine Conversions
04-14-2008, 11:23 AM
Replies: 76
Views: 7,667
Posted By hackinboy

RE: weedeater/chainsaw 39cc for free, where to start?

Fozjared,
You can certainly run a bolt through a starter cone and chuck it up in your drill. I''ve always found that it feels a bit ackward though, its not as easy to apply straight pressure on...
Forum: Engine Conversions
04-11-2008, 01:09 PM
Replies: 76
Views: 7,667
Posted By hackinboy

RE: weedeater/chainsaw 39cc for free, where to start?

Ralph,
I think that was $2.20 a liter, about $8.35 a gallon. yikes!
Forum: Engine Conversions
04-08-2008, 12:27 PM
Replies: 64
Views: 7,203
Posted By hackinboy

RE: Elect. ignition for Poulan 25cc?

Nitro Joe
I've been running mine on 6V, the owners manual (term manual used very loosely here) states to make sure the voltage isn't below 5.5V. It doesnt state what will happen if it falls below...
Forum: Engine Conversions
04-07-2008, 01:45 PM
Replies: 64
Views: 7,203
Posted By hackinboy

RE: Elect. ignition for Poulan 25cc?

I wanted the answer to that also so I brought my timing light to the field yesterday but it got too windy so I gave up. I planned on trying the light tonight after work. Hopefully I'll be able to...
Forum: Engine Conversions
04-07-2008, 11:02 AM
Replies: 64
Views: 7,203
Posted By hackinboy

RE: Elect. ignition for Poulan 25cc?

Jim,
Im using a 5 cell 2100 mah. There are no instructions with the unit. On the actual ignition box it just says 6 volts. I know alot of the units use 4.8-6V but i didnt try a 4 cell. I'll try...
Forum: Engine Conversions
04-07-2008, 09:26 AM
Replies: 64
Views: 7,203
Posted By hackinboy

RE: Elect. ignition for Poulan 25cc?

Jim,
I have a couple of those ignitions on Ryobis, you'll be pleased. I use the 1/8th inch rare earth magnets from Radio Shack. It does matter which way the magnet is mounted. Just hook up your...
Forum: Engine Conversions
02-25-2008, 11:01 AM
Replies: 10
Views: 1,208
Posted By hackinboy

RE: Need Ryobi part....

Send me a PM with an address and i will send you one
Forum: Engine Conversions
01-18-2008, 11:56 AM
Replies: 7
Views: 2,484
Posted By hackinboy

RE: how to build a muffler

Check out this website. Ive built a few mufflers (Ryobi 31cc's) this way and they worked great.
http://www.rcfaq.com/ANSWERS/ENGINES/mufflerplans.htm
Showing results 1 to 21 of 21


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.