RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: ChrisCifra
Showing results 1 to 13 of 13
Search took 0.44 seconds.
Forum: The Clubhouse
12-31-2010, 02:29 PM
Replies: 2
Views: 964
Posted By ChrisCifra

Tower Super Saver Codes

I am itching to place an order with Tower Hobbies but I deleted my Super Saver email with the coupon codes. Does anyone have the current Super Saver code for $25 off $150?

Thanks
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
08-09-2010, 10:02 AM
Replies: 4
Views: 704
Posted By ChrisCifra

RE: 8FG - Sailplane mode for an Airplane?

I am currently using a PMix for this and it works pretty good. With a PMix the mix happens faster than the gear, which is very slow to move. It seems like adding a mix delay would make things much...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
08-08-2010, 10:26 PM
Replies: 4
Views: 704
Posted By ChrisCifra

8FG - Sailplane mode for an Airplane?

I just received my new 8FG and am trying to set it for my P40. I would like to setup the gear better than with my 8UAP. The gear moves backwards when it goes up, which causes the CG to change a lot...
Forum: Kit Building
05-26-2009, 02:42 PM
Replies: 4
Views: 961
Posted By ChrisCifra

RE: 1/6 Pica Waco Engine and Mounting

I do have an OS120 4 stroke sitting around, but thought that it would be way too much engine for the plane. Maybe I will give it a second look.

Chris
Forum: Kit Building
05-26-2009, 01:38 PM
Replies: 4
Views: 961
Posted By ChrisCifra

1/6 Pica Waco Engine and Mounting

Hello,
I am building a 1/6 Pica Waco Kit and even after searching the vast number of positing on the Waco I have a couple of questions about engines and mouting, .

First, does anyone have...
Forum: Golden Age, Vintage & Antique RC
01-26-2009, 09:50 PM
Replies: 19,483
Views: 2,707,498
Posted By ChrisCifra

RE: WACO YMF

I've just started building a 1/6th laser cut Pica Waco. I am building the top wing center section and am about to attach the shear webs to the front spars. But the spars are not parallel to each...
Forum: Kit Building
01-26-2009, 08:41 PM
Replies: 1
Views: 365
Posted By ChrisCifra

Pica Waco Shear Webs

I've just started building a 1/6th laser cut Pica Waco. I am building the top wing center section and am about to attach the shear webs to the front spars. But the spars are not parallel to each...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
10-21-2008, 09:13 PM
Replies: 12
Views: 1,375
Posted By ChrisCifra

RE: Glitching problems that I cannot solve

The engine is not running.
The antenna routes externally, straight up from receiver through top of plane and then to tail, but I have tried different orientations.
The batteries and switches are...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
10-21-2008, 08:18 PM
Replies: 12
Views: 1,375
Posted By ChrisCifra

Glitching problems that I cannot solve

I have a new plane (27% Midwest Cap) that is having glitching problems. I noticed several times in the air apparent glitches mostly with the plane passing directly in front of me. So I started to...
Forum: Glow Engines
07-23-2008, 11:20 PM
Replies: 4
Views: 852
Posted By ChrisCifra

OSBGX-1 Break-in Procedure?

I seem to be missing the manual for my BGX-1. Can someone tell me what the break-in procedure is? Also what is the initial needle setting? With my other OS engines I ran them at full throttle as...
Forum: Glow Engines
12-21-2007, 02:09 PM
Replies: 3
Views: 778
Posted By ChrisCifra

OS BGX-1 Backplate Mount

I am planning on using the backpate mount which comes with the OS BGX-1 engine. Should I use any type of thread locker or lock washers when attaching the mount to the engine? It comes with lock...
Forum: Batteries & Chargers
12-18-2007, 06:05 PM
Replies: 7
Views: 1,033
Posted By ChrisCifra

RE: Parallel RX Batteries

I am also going to use 2 RX Batteries and want to be able to charge them at the same time. I was going to use the Sirius Charge Limited Edition (Dual Output charger) until I learned about the issues...
Forum: Kit Building
07-24-2007, 02:30 PM
Replies: 3
Views: 1,058
Posted By ChrisCifra

Engine for Midwest Cap 232

I am building a Midwest Cap 232 with the airfoiled tail, and would like some help deciding on which engine to use. I want to use a 2 Stroke Glow Engine. 4 Strokes are too expensive and gas is now...
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.