RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Community
Search
Notices
Search: Posts Made By: vtrebel
Showing results 1 to 15 of 15
Search took 0.35 seconds.
02-09-2008, 07:57 PM
Replies: 19
Views: 1,181
Posted By vtrebel

RE: High idle with brake on throttle back

how big is your carb opening?
01-06-2008, 02:29 PM
Replies: 5
Views: 841
Posted By vtrebel

RE: How does motor attach to pull start?

i learned this one the hard way too. you would think redcat would show the bearing in the manual but they dont. Its not a cheap part either to be throwing away with the broken pull starter like i...
12-02-2007, 11:23 PM
Replies: 7
Views: 802
Posted By vtrebel

RE: Clutch Bell

it goes in the same way but i had to add 2 5x10x.5 HPI washers to the outer set because the HPI clutch wiggles a little with the stock set of bearings and washers. Hope that helps.
11-24-2007, 05:40 PM
Replies: 4
Views: 747
Posted By vtrebel

RE: volcano pull start

sounds good. i just went ahead and ordered a new pull start from clermont, hopefully that comes with the screws and i dont even have to deal with it.
11-24-2007, 04:22 PM
Replies: 4
Views: 747
Posted By vtrebel

volcano pull start

So all 4 screws in my pull start backed out on thanksgiving and i wanted to know if anyone knew what size they were. The manual doesn't give a size and i would rather go to my lhs or lowes and get...
11-15-2007, 08:58 PM
Replies: 18
Views: 1,199
Posted By vtrebel

RE: Volcano SV problem

i need the those and hex's. the hex's are torn up where the other brand axles werent holding them on tight
11-15-2007, 08:52 PM
Replies: 18
Views: 1,199
Posted By vtrebel

RE: Volcano SV problem

hey clermont.... i dont see the wheel hex's on your site. do you carry them?
11-15-2007, 08:39 PM
Replies: 18
Views: 1,199
Posted By vtrebel

RE: Volcano SV problem

all stock, only thing i did was put the front shock mounts on the lower most outer hole and the back in the upper most inner hole makes it look like a trophy truck. really it was a compression...
11-15-2007, 08:23 PM
Replies: 18
Views: 1,199
Posted By vtrebel

RE: Volcano SV problem

thanks guys, feel kinda stupid cause that was the only part i didnt check. well it was a blast for the 3 minutes my buddy was hammering on it. he got it to stand up and rode a wheelie for about 5...
11-15-2007, 08:15 PM
Replies: 18
Views: 1,199
Posted By vtrebel

RE: Volcano SV problem

so i think i know the prob. i bought some non redcat drive cups and they were round all the way instead of the flat spot on the redcat ones. so they spin freely. so i guess i need to order some new...
11-15-2007, 08:01 PM
Replies: 18
Views: 1,199
Posted By vtrebel

RE: Volcano SV problem

thanks bro, will let you guys know if i get her going
11-15-2007, 07:57 PM
Replies: 18
Views: 1,199
Posted By vtrebel

RE: Volcano SV problem

where is the slipper clutch? I'll check the grub screws too
11-15-2007, 07:47 PM
Replies: 18
Views: 1,199
Posted By vtrebel

Volcano SV problem

So i took my truck out today and after about 3 mins it just rolled to a stop even though i was on the gas. Now when i pick it up and hold it and give it gas the tires turn and everything is good....
10-01-2007, 03:43 PM
Replies: 6
Views: 596
Posted By vtrebel

RE: is the sv good

Yeah its a tough little truck. I recomend upgrading the shocks to the aluminum ones though. I bent or broke all eight in the first two weeks i had it. you can get the redcat ones or traxxas t-max...
09-17-2007, 04:22 PM
Replies: 1,708
Views: 207,944
Posted By vtrebel

RE: Redcat Racing Volcano Thread

I'm new to this sport and recently bought a Volcano SV and LOVE IT!!! After breaking in the engine and getting the concept of these powerful little trucks i decided i would see what it could do in...
Showing results 1 to 15 of 15


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.