RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 2
1
2
Search: Posts Made By: cybane
Showing results 1 to 25 of 37
Search took 0.57 seconds.
Forum: Car Nitro & Gas Engines
03-05-2008, 06:07 PM
Replies: 4
Views: 557
Posted By cybane

RE: Replace this engine or is it still good?

It is an OS MAX .12TR

When I had it together and the flow plug installed I was never able to turn it over with my finger at all no matter how much I tried. It did run well before I took it...
Forum: Car Nitro & Gas Engines
03-05-2008, 12:00 PM
Replies: 4
Views: 557
Posted By cybane

Replace this engine or is it still good?

Okay so I am still in the process of my rebuild and all of the following pictures are after I have done my best to clean the engine with denatured alcohol on the inside and simple green + denatured...
Forum: Car Nitro & Gas Engines
03-04-2008, 04:18 PM
Replies: 2
Views: 640
Posted By cybane

Engine and Carb Question .12TR

I have the OS Max .12TR and I believe the http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXKGJ9&P=V. I did not buy this myself but from the looks they are the same and without an expert looking at...
Forum: RC Giant Scale Cars
03-04-2008, 08:04 AM
Replies: 29
Views: 2,404
Posted By cybane

RE: Stainless screw/bolt kits?

Fast Eddy can you provide a link to the HexHead screws. I have been unable to find those unless you mean Hexcrews but I just wanted to check it out first.
Forum: RC Car General Discussions
03-04-2008, 12:52 AM
Replies: 4
Views: 556
Posted By cybane

RE: Truck Cleaning

Okay I think I finally found the best way for me to get everything clean and not break the bank while helping the environment.

The Reusable spray bottle...
Forum: RC Car General Discussions
03-03-2008, 11:08 PM
Replies: 4
Views: 556
Posted By cybane

RE: Truck Cleaning

How do you like the one from ebay? Also what kind of solvent do you use with yours? Would a 2-3 gal compressor be enough to run that long enough to clean a truck?

I think I might go with this...
Forum: RC Car General Discussions
03-03-2008, 05:38 PM
Replies: 4
Views: 556
Posted By cybane

Truck Cleaning

Well after doing a complete break down cleaning of the used RC10GT I bought I never want to do this again. I am looking for some kind of pressurized solution but want something small that doesn't...
Forum: RC Nitro Stadium Trucks
03-02-2008, 05:18 PM
Replies: 12
Views: 1,582
Posted By cybane

RE: RC10GT Rebuild Project

Do you have the .18 TZ(S) with the 11L carb in it? Not able to tell the exact engine from the picture.
Forum: RC Nitro Stadium Trucks
02-26-2008, 03:17 AM
Replies: 12
Views: 1,582
Posted By cybane

RE: RC10GT Rebuild Project

Here is my plan and current situation. To get my engine off the mount I had to take off the manifold and head to get at the mount screws. There was no shim between the head and sleeve so that made me...
Forum: RC Nitro Stadium Trucks
02-25-2008, 04:39 PM
Replies: 12
Views: 1,582
Posted By cybane

RE: RC10GT Rebuild Project

Well after seeing those trucks tear it up with that larger engine it really made me want to put one in. However, I use a bump start and think I will go with the .18TZ...
Forum: RC Nitro Stadium Trucks
02-25-2008, 04:14 PM
Replies: 12
Views: 1,582
Posted By cybane

RE: RC10GT Rebuild Project

Wouldn't a .18 be too much engine for my truck?
Forum: RC Nitro Stadium Trucks
02-25-2008, 02:29 PM
Replies: 12
Views: 1,582
Posted By cybane

RC10GT Rebuild Project

Okay so I am still super new to this hobby and the one thing I have not yet done is actually become familiar with either of my trucks. However, this is going to change and I plan to clean and rebuild...
Forum: RC Nitro Stadium Trucks
02-19-2008, 06:27 PM
Replies: 4
Views: 506
Posted By cybane

RE: Engine Troubles

I did just like you guys advised made sure all fuel was out and then I put in some Odonnell 20% and it started right up. Going to get a temp gun in the next few days.
Forum: RC Nitro Stadium Trucks
02-19-2008, 04:42 PM
Replies: 4
Views: 506
Posted By cybane

RE: Engine Troubles

It is a Bump Start engine and I will do that once I get my hands on a tool that I can remove the glow plug. Still trying to find the size on those darn things so I can run to the hardware store and...
Forum: RC Nitro Stadium Trucks
02-19-2008, 12:35 AM
Replies: 4
Views: 506
Posted By cybane

Engine Troubles

Well we had a swap meet at my local club (CRCRC) and I picked up a RC10GT with everything but a receiver in it. He was unable to start it due to not having any fuel with him but from the looks of...
Forum: RC Electric Off-Road Trucks, Buggies, Truggies and more
02-14-2008, 05:14 PM
Replies: 0
Views: 294
Posted By cybane

Balancer Adpaters

I plan on using an ICE Charger and plan to move onto LiPo and want to get a pass through balancer that would be usable for multiple kinds of batteries. Now there are a few brands of batteries that I...
Forum: RC Electric Off-Road Trucks, Buggies, Truggies and more
02-12-2008, 11:42 PM
Replies: 11
Views: 552
Posted By cybane

RE: novak and lrp

Currently I am trying to decide myself between getting either the Novak GTB SS 13.5 Combo or the LRP Sphere Competition TC-Spec Brushed/Brushless Speed Control a 13.5t motor for racing at my local...
Forum: RC Electric Off-Road Trucks, Buggies, Truggies and more
02-11-2008, 07:38 PM
Replies: 3
Views: 477
Posted By cybane

Need some clarification about upgrading a XXX-T

I have a first generation XXX-T that I am wanting to upgrade a few of the parts of the current XXX-T CR. The most interesting part I have found that I would want to upgrade is rear tire mounting...
Forum: RC Car General Discussions
02-09-2008, 06:15 AM
Replies: 3
Views: 514
Posted By cybane

If you could only have one toolbox?

I am trying to find a single toolbox solution for my RC needs. Now I think I have found it from Stanley called the FatMax...
Forum: RC Electric Off-Road Trucks, Buggies, Truggies and more
02-07-2008, 06:36 PM
Replies: 1
Views: 369
Posted By cybane

What tools do you use?

I am wondering about people have the XXX-T. I recently bought one used and I am trying to track down what sizes of tools I am going to need to disassemble and reassemble? I think it uses SAE Hex...
Forum: MaxAmps Support
02-07-2008, 04:27 AM
Replies: 5
Views: 799
Posted By cybane

RE: 7.4v with charger?

Get the http://www.maxamps.com/Skyway-A2078-Charger.htm and http://www.maxamps.com/Lipo-4000-74-Pack.htm but make sure you get the Align tips.
Forum: Batteries & Chargers
02-07-2008, 03:55 AM
Replies: 1
Views: 419
Posted By cybane

RE: Would this be a good lipo setup?

Anyone much about this charger? http://www.maxamps.com/Skyway-A2078-Charger.htm
Forum: Batteries & Chargers
02-07-2008, 03:39 AM
Replies: 1
Views: 419
Posted By cybane

Would this be a good lipo setup?

I am going to be changing to LiPos shortly and I am wanting to get a good charger/balancer all in one. I was thinking of going with this Charger and this LiPo. I can not decide which would be...
Forum: RC Electric Off-Road Trucks, Buggies, Truggies and more
02-06-2008, 06:07 AM
Replies: 1
Views: 268
Posted By cybane

Add a Camera to your Truck

Well I was thinking about mounting a camera on my truck if I ever get disposable cash just for fun. So far the one I like is http://www.spygearco.com/MiniWirelessSpyCamera.htm. Would be a great way...
Forum: RC Car General Discussions
02-06-2008, 01:52 AM
Replies: 16
Views: 1,359
Posted By cybane

RE: Workbench Questions

For the mat I was thinking of getting some of that rubber shelfing stuff people use to prevent slips or just making her sew me up a nice mat.
Showing results 1 to 25 of 37
 
Page 1 of 2
1
2


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.