RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: aggiegolfer
Showing results 1 to 10 of 10
Search took 0.35 seconds.
Forum: Glow Engines
03-01-2010, 10:08 AM
Replies: 1
Views: 508
Posted By aggiegolfer

OS .10 fsr muffler question

can I swap the 761 that comes with the engine with the 871? Are they compatible?


Thanks for any help
Forum: O.S. Engines Support
02-23-2010, 11:00 AM
Replies: 2
Views: 548
Posted By aggiegolfer

RE: .10 FSR Muffler Question

Thanks for the quick response. Do you happen to know if the 871 will fit the .10 FSR? If I were to tap a new hole, do I have to plug the hole that is there now? If so, any ideas on how to go...
Forum: O.S. Engines Support
02-23-2010, 05:53 AM
Replies: 2
Views: 548
Posted By aggiegolfer

.10 FSR Muffler Question

I gleaned from previous posts that the 761 muffler that comes with the .10 FSR does not contain a pressure fitting, as it is most likely unnecessary. My question:

If I do want a pressure...
Forum: Questions and Answers
02-22-2010, 07:17 PM
Replies: 6
Views: 616
Posted By aggiegolfer

RE: Issue with Fuel Tank

Thanks for all the help.
Forum: Questions and Answers
02-22-2010, 07:51 AM
Replies: 6
Views: 616
Posted By aggiegolfer

Issue with Fuel Tank

The stopper on my sullivan fuel tank won't seal properly. After I screw everything it, the stopper still won't seat. I made sure not to over-tighten the screw, and it does not appear that the tank...
Forum: Beginners
01-19-2010, 02:53 AM
Replies: 3
Views: 1,348
Posted By aggiegolfer

Fuel Tank Size ?

I'm finishing up my first scratch build, The Daydreamer, from some rcm plans. The plans call for a .09-.10 engine, and a 1oz. tank. Recommended flying weight is 32oz. I have a 2oz tank that fits...
Forum: Questions and Answers
01-18-2010, 09:37 AM
Replies: 1
Views: 438
Posted By aggiegolfer

Fuel tank size question

I'm finishing up my first scratch build, The Daydreamer, from some rcm plans. The plans call for a .09-.10 engine, and a 1oz. tank. Recommended flying weight is 32oz. I have a 2oz tank that fits...
Forum: Questions and Answers
09-28-2009, 07:25 AM
Replies: 3
Views: 526
Posted By aggiegolfer

A few questions concerning my first build

Hello all!

I have a few random questions about my first build. I decided to go scratch for my first ever build so a lot of these questions I'm sure are elementary, but here goes:

Some...
Forum: Beginners
05-06-2008, 09:39 PM
Replies: 7
Views: 1,257
Posted By aggiegolfer

RE: wing bolt block question

Thanks for the help. The blocks are going inside the wings. So should I take the balsa, drill the hole, then just saturate around the hole with thin CA?
Forum: Beginners
05-06-2008, 09:24 PM
Replies: 7
Views: 1,257
Posted By aggiegolfer

wing bolt block question

I am scratch building a little sport plane of RCM plans and I can't figure this out. The plans call for a wing bolt filler block to be positioned at the trailing edge. I understand its function. ...
Showing results 1 to 10 of 10


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.