RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 3
1
2
3
Search: Posts Made By: Star7
Showing results 1 to 25 of 74
Search took 0.34 seconds.
Forum: Glow Engines
06-30-2010, 08:17 PM
Replies: 6
Views: 913
Posted By Star7

RE: ***MAGNUM 46***HELP!!!!!

You might also put a short section of stiff tubing inside the tank in the clunk line. Sometimes it folds over on itsef for just a short period and kinks. A short piece of stiff tubing will let it...
Forum: Glow Engines
06-14-2010, 05:18 PM
Replies: 1,776
Views: 196,147
Posted By Star7

RE: Club MAGNUM !

Chris, how much fuel have you run through the 52? They may not like to idle until well broken in. I have found the idle mixture setting is relatively narrow so make only small adjustments at a time....
Forum: Beginners
06-14-2010, 04:26 PM
Replies: 22
Views: 2,583
Posted By Star7

RE: Escapade

I just put a bridge across the cheeks under the front of the motor. Otherwise the cheeks tend to bust right off in the first nose over.
Forum: Kit Building
06-09-2010, 02:37 PM
Replies: 44
Views: 5,999
Posted By Star7

RE: BTE Venture 60 kits shipping soon!

Thanks again for bringging the venture back. I just got my kit and is is beautiful quality.
Forum: Everything Diesel
06-07-2010, 05:27 PM
Replies: 3
Views: 1,157
Posted By Star7

RE: Saito Diesel

That's is very nice! Thanks for the video.
Forum: Kit Building
06-07-2010, 04:55 PM
Replies: 16
Views: 9,931
Posted By Star7

RE: Hobby King Covering film any good?

I felt that it required a lower iron setting than monocoat but it has been a while since I used lots of monocoat. I think it works just fine. I do not think that it is as stretchy as ultracoat. You...
Forum: RC Warbirds and Warplanes
06-03-2010, 06:37 PM
Replies: 26
Views: 5,436
Posted By Star7

RE: Best 60 size P47 Thunderbolt

cna I am very uncomfortable with those connectors. It looks like you have room for a zee or you could solder on a ball joint link or cleavis. ymmv
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
05-20-2010, 02:42 PM
Replies: 5
Views: 1,198
Posted By Star7

RE: Buddy box settings for Airtronics RDS8000

This also allows setting high rate for the instructor's box without it being available to the student. It is important that if the Instructor takes off and trims the model, he lets the student know...
Forum: Questions and Answers
05-18-2010, 06:30 PM
Replies: 15
Views: 2,383
Posted By Star7

RE: **Read Poll Question First (In First Post)** then make your selection! SILENT POLL

I assume that the film I get from Hobby King is the infamous 'chinacoat' (which works just fine) and my ultracoat has never done that, soooo......
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
05-18-2010, 04:51 PM
Replies: 885
Views: 163,191
Posted By Star7

RE: MAN reports on Airtronics SD-10G 2.4Ghz radio system

I have known people that shifted to trays with wrist rests because of arthritis or carpal tunnel surgery gone bad. It seems like not having to hold the transmitter gives them better resolution. I fly...
Forum: Beginners
05-13-2010, 03:31 PM
Replies: 14
Views: 1,466
Posted By Star7

RE: How to identify and value inherited planes?

I would recommend doing a search with AMA for local clubs and checking to see if any have a swap meet or club auction scheduled. These kind of events can help you move the planes and other hard to...
Forum: RC Fuels
05-07-2010, 04:02 PM
Replies: 9
Views: 4,647
Posted By Star7

RE: Nitro Fuel killed my grass

It seems that it only kills grass or other desired plants. The test stand at our field is knee high in weeds. figures
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
04-27-2010, 01:08 PM
Replies: 14
Views: 2,404
Posted By Star7

RE: Airtronics VG6000 help

Sorry, I have nothing better. He cannot have blown the diode because the transmitter turns on. He swapped the crystal into another transmitter and got function so I don't think the crystal is the...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
04-26-2010, 07:58 PM
Replies: 14
Views: 2,404
Posted By Star7

RE: Airtronics VG6000 help

I do not have a VG6000, is this capable of PCM? If so, is it possible that you got it turned onto pcm mode?
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
04-26-2010, 04:38 PM
Replies: 14
Views: 2,404
Posted By Star7

RE: Airtronics VG6000 help

Since the transmitter turns on, it isn't a blown diode so I have to say that something got jostled loose during the battery change. I would take a minute with the back off to just look at all...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
04-23-2010, 02:50 PM
Replies: 4
Views: 912
Posted By Star7

RE: Li Po Storage Box

I use two boxes on the theory that if I have a fire it will probably be during charging and I don't want to endanger stored packs. I use ammo cans lined with sheet rock. I have a welder but am lazy.
Forum: Questions and Answers
04-19-2010, 07:10 PM
Replies: 12
Views: 1,207
Posted By Star7

RE: Question about old engines

To amplify MinnFlyer's comment: It can be tough in some models to route the fuel line to a rear mounted needle valve....the tank/firewall can be so close that you either get a kink or need a BIG loop...
Forum: Airtronics Support Forum
03-25-2010, 06:18 PM
Replies: 2,617
Views: 363,967
Posted By Star7

RE: *Airtronics RD8000 2.4 GHz*

Andrewskj, the actual antenna is the ~1.5" smaller diameter end of each of the black leads. The rest is shielded coax. Only the very tips need to be at 90 degrees. I would try to keep those ends a...
Forum: Beginners
03-16-2010, 04:23 PM
Replies: 12
Views: 5,426
Posted By Star7

RE: I need to build a rc aircraft in one month please help

If it has to be "scratch" built and you can source materials in Sri Lanka, I recommend a foam plane with a profile fuselage. There are various plans online free. Pick one specifically designed as a...
Forum: Beginners
02-24-2010, 03:48 PM
Replies: 40
Views: 3,835
Posted By Star7

RE: How to land a trainer with a loooong glide

It sin't a beginners tactic but gentle cross control of aileron and rudder will slip you in. Be sure to practice at a goodly altitude as it is a mattter of balance! This is used in full scale planes...
Forum: Electric General Discussion
01-18-2010, 08:35 PM
Replies: 8
Views: 2,099
Posted By Star7

RE: Hawker hurricane

That is really nice, Jeff. Great photos as well.
Forum: Kit Building
01-14-2010, 06:20 PM
Replies: 28
Views: 3,512
Posted By Star7

RE: Good news from SIG

I ordered a 4* kit three weeks ago and got it about ten days ago. There was a death in their management a year or so ago that interrupted communications with the Chinese factory that produces the...
Forum: Glow Engines
01-11-2010, 06:12 PM
Replies: 5
Views: 1,595
Posted By Star7

RE: Magnum XL 91 FS Potential Problem

The carb will wobulate about the o-ring in the manifold when the carb bolts are loose. Mine seals fine. Both of my 91fs came with bent chokes. I removed both and have no air leaks so far. The motors...
Forum: Classic RC Pattern Flying
12-29-2009, 07:18 PM
Replies: 11
Views: 2,629
Posted By Star7

RE: An interesting tid bit on the Tower Kaos 40

Very Cool!, thanks for the link. The purple looks nice.
Forum: Tips & Techniques
12-15-2009, 05:44 PM
Replies: 22
Views: 2,857
Posted By Star7

RE: Covering for plans

tacx, did you have any residue left from the press and seal? My efforts left a hazy coat on everything that I had the press and seal stuck on. The residue did not wipe off with alcohol. I was afraid...
Showing results 1 to 25 of 74
 
Page 1 of 3
1
2
3


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.