RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Community
Search
Notices
Search: Posts Made By: techpro
Showing results 1 to 14 of 14
Search took 0.30 seconds.
03-14-2010, 05:42 PM
Replies: 646
Views: 82,533
Posted By techpro

RE: Nomadio React 2.4GHz Radio

Thanks i'll try and find a 5 volt regulator.
03-14-2010, 05:13 PM
Replies: 0
Views: 1,008
Posted By techpro

NOMADIO REACT 7.4 VOLT LIPO QUESTION

Can anyone tell me what the highest voltage i can run through my nomadio react is. i just bought a 2 cell 7.4 volt lipo,is 6 volts too much,can i use a team associated 6 volt regulator,or does it...
03-14-2010, 05:06 PM
Replies: 646
Views: 82,533
Posted By techpro

RE: Nomadio React 2.4GHz Radio

can anyone tell me the most voltage i can run through my nomadio react.i just bought a 7.4 volt 2 cell lipo,can i use a 6 volt regulator like the red team associated one or does it have to be a 5...
12-31-2008, 06:53 PM
Replies: 2
Views: 1,043
Posted By techpro

RE: rc18/ hitec 65 mg servo

thank you gex 61,you were a great deal of help,hardware store here i come.
12-31-2008, 05:07 PM
Replies: 2
Views: 1,043
Posted By techpro

rc18/ hitec 65 mg servo

i have a hitec hs 65 mg to install in my rc18b the screw to hold the sevo saver/horn in front is way too short,does anyone know the exact size so i can get a longer one.
12-25-2008, 10:43 AM
Replies: 2
Views: 467
Posted By techpro

RE: rc 18 hitec servo

Thanks for your help Mr Mugen that looks like the one in the FT kit i got.happy holidays.
12-25-2008, 09:38 AM
Replies: 2
Views: 467
Posted By techpro

rc 18 hitec servo

can anyone tell me if the hs 85 mg hitec servo will work on my rc 18 b with the servo saver's that come in the fact team kit,thanks.
12-07-2008, 02:29 PM
Replies: 3
Views: 1,409
Posted By techpro

nomadio react lipo

I have a nomadio react want to use a lipo batt. amainhobbies has one to fit my radio. The charger i have is an MRC 989 super brain,it is suppose to charge lipo's it is'nt a balance charger i dont...
10-10-2008, 06:52 PM
Replies: 9
Views: 984
Posted By techpro

RE: Vspec VZB Dyno

I WAS LOOKING AT THE NEEDLE SETTINGS ON THE LSN 1 3/4 TURN OUT HOW MUCH DIFFERENCE IS THAT FROM FACTORY BEING FLUSH.THANKS.
Replies: 3
Views: 398
Posted By techpro

NIMH TO LIPO T4

I WAS THINKING ABOUT SWITCHING TO A LIPO PACK ON MY T4 I KNOW THERE'S A WEIGHT DIFFERENCE FROM NIMH TO LIPO, I HEARD ABOUT A LEAD PLATE OF SOME SORT,DOES ANY ONE KNOW ABOUT THIS AND WHERE I COULD GET...
09-28-2008, 06:10 AM
Replies: 12
Views: 850
Posted By techpro

RE: Which Brushless System

the mamba max system by castle creations is a great setup for the money 5700,6900 ,77000.e-bay 180.00
09-27-2008, 08:32 PM
Replies: 11
Views: 1,076
Posted By techpro

RE: v-spec issues

hey bill,just broke in a new eb modded v-spec with 30% should i make sure it has the second 0.1 shim between the head and is the
p3 plug ok to use,thanks
09-21-2008, 11:15 AM
Replies: 11
Views: 1,076
Posted By techpro

RE: v-spec issues

my front bearing does leak/or seep fuel ,the crank pin has slop too even after replacing the con rod,the motor may be too expensive to fix compared to buying a new one,just thought i'd get some more...
09-21-2008, 09:29 AM
Replies: 11
Views: 1,076
Posted By techpro

v-spec issues

hi bill,i have a v-spec with almost six gallons on it had sleeve pinched replace con rod, motor stil has a low end bog,the motor might be too far gone,any insight would help.
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.