RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: rcsws
Showing results 1 to 18 of 18
Search took 0.29 seconds.
Forum: Glow Engines
10-10-2016, 07:26 AM
Replies: 4
Views: 1,243
Posted By rcsws

Okay, may not be normal but here is what I do to...

Okay, may not be normal but here is what I do to adjust the low end on most two cycle carbs.

1) Remove carb from engine
2) Set high end needle at factory recommended setting usually two and a...
06-15-2016, 12:45 PM
Replies: 484
Views: 52,699
Posted By rcsws

Thanks, will check it out when I get home.

Thanks, will check it out when I get home.
06-15-2016, 12:25 PM
Replies: 484
Views: 52,699
Posted By rcsws

Sorry, not at home right now so I do not know. ...

Sorry, not at home right now so I do not know. What should I look for?
06-15-2016, 11:51 AM
Replies: 484
Views: 52,699
Posted By rcsws

Quick question. Have a DX18 Gen1, less then five...

Quick question. Have a DX18 Gen1, less then five months old. First got it and ended up having to recalibrate it. Did so at the direction of your staff after going through everything else. Was...
12-15-2015, 06:34 AM
Replies: 5,280
Views: 383,407
Posted By rcsws

So congress passes legislation that prevents...

So congress passes legislation that prevents regulation and the FAA/DOT ignores it. That is the AMA's fault? The AMA should sue to have this whole thing tossed and should sue for damages as well. ...
Replies: 485
Views: 61,694
Posted By rcsws

Since there are so many disappointed Spektrum...

Since there are so many disappointed Spektrum customers out there, I would lo0ve to buy a 9 channel for the right price. Any buddy offering to sell at a real cheap price?
12-17-2013, 09:06 AM
Replies: 224
Views: 31,946
Posted By rcsws

With regards to strength, nobody has addressed...

With regards to strength, nobody has addressed what type of strength. Are we talking compression or tension? My opinion, glass coating adds a great deal of strength in tension and very little in...
04-24-2013, 07:33 AM
Replies: 1
Views: 559
Posted By rcsws

Fibreglass Atlanta Pattern Ship

I have two Atlanta Pattern ships. One with spring airs, YS 60 (spare gaskets and diaphrame), pipe etc. The other bare bones. The equiped one has maybe ten flights on it and needs minor work due to...
Replies: 44
Views: 7,456
Posted By rcsws

RE: DX7s throttle reversed, trim wont work

Something you may want to look at is a switch turned on for Throttle Cut. If the Throttle cut is set for one direction and you reverse the throw it may be going the wrong way and locking you out ...
Forum: RC Tanks
05-21-2012, 01:27 PM
Replies: 34
Views: 3,487
Posted By rcsws

RE: Pershings In The Korean War?

The end date is correct- Offical cease fire, per the written orders I have in my possesion was to start on 27 2200 Jul 53. I have the order as well as the document that was to be signed by everyone...
08-03-2010, 12:55 PM
Replies: 193
Views: 24,540
Posted By rcsws

RE: Which JR\Spectrum receiver did you crash with?

You are a little sensitive and greatly insulting. I post one question, for MY OWN INFORMATION and you chastize me for not viewing a video that you so proudly posted. You assumed, and you know what...
08-02-2010, 09:19 PM
Replies: 193
Views: 24,540
Posted By rcsws

RE: Which JR\Spectrum receiver did you crash with?

I must be stupid here- is it not possible that in some areas there is more 2.4 stray signals in the air that could cause interference? I know certain flying sites have problems on certain old freq...
Forum: Kit Building
04-27-2010, 11:34 AM
Replies: 3,197
Views: 362,011
Posted By rcsws

RE: *** Ultra Sport Brotherhood ***

I guess that makes me 31- have owned fiv e US 40's
Forum: Seaplanes
11-30-2009, 02:35 PM
Replies: 163
Views: 21,881
Posted By rcsws

RE: Please help me do the unthinkable ...

I have just read this entire saga. Most have given good advice, but nobody mentioned a not so small safety factor.

It is one that we all have forgotten from time to time and some have paid...
10-27-2009, 07:51 PM
Replies: 76
Views: 22,879
Posted By rcsws

RE: Royal P-51D build

I am in the process of building a Royal P-51 from plans. I took a set of 19 to 40 size plans and upsized them to a 58" wing span. I am looking to power it with a 70 four stroke. I know I have a VQ...
12-13-2008, 10:19 PM
Replies: 4
Views: 807
Posted By rcsws

RE: P-51 Help

I am actually looking for a little more scale than the two kits mentioned. I could always start with the Great Planes kit and bash it I guess but I really wanted to "scale it up" if you know what I...
12-12-2008, 05:24 PM
Replies: 4
Views: 807
Posted By rcsws

RE: P-51 Help

I would be interested. Do you have any details on the kit or know where I might find some?
12-12-2008, 04:26 PM
Replies: 4
Views: 807
Posted By rcsws

P-51 Help

I am looking to build a P-51 .40 size aircraft, good scale kit or scratch. Anybody have thoughts on plans or kits?
Showing results 1 to 18 of 18


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.